Network Settings Page - Canon VB101 User Manual

Detail Settings

Network Settings Page

Use this page to specify the settings for connecting to an Ethernet or PPP network.
For a LAN connection, specify Ethernet settings. For connections made with a modem, specify
PPP settings
If you are using Ethernet, take particular care with the IP address, subnet mask
c
and route settings. If any of these items an error, you may be completely unable
Note to access the system via Ethernet and it may only be possible to recover the
problem by using the initial setup tools to correct the error.
33 38
Ethernet
Specifies the same settings as the Basic
Settings page.
"Use Ethernet"
Tick this checkbox to use Ethernet.
"Address Setting Method"
If you select "Auto Setting (Bootp)", the IP
address is automatically acquired by the
Bootp server after restart. If you select
"Manual Setting", enter the IP address
and subnet mask also.
"Give priority to Bootp option when
deciding subnet mask."
If you tick this option, the subnet mask
specified by the Bootp server is given
priority over the subnet mask address
specified below when "Auto Setting
(Bootp)" is selected as the address
setting method.
"Give priority to Bootp option when
deciding gateway address."
If you tick this option, the gateway
address specified by the Bootp server is
given priority over the default gateway
address specified below when "Auto
Setting (Bootp)" is selected as the
address setting method.
"IP Address"
Enter a network interface-specific IP
address.
"Subnet Mask"
Enter the subnet mask specified for the
network to be connected.
If you selected "Auto Setting (Bootp)" as
the address setting method, check that
the Bootp server has been started up.
Contact the network administrator for the
IP address, subnet mask, and static
routes settings.
"Static Route Control"
Route control is required when you are communicating over a
wide area network via a router. When you are using both
Ethernet and PPP, set the route as required.
"Default Route"
Specifies the same setting as "Default Gateway Address" on
the Basic Settings page. Specify the route normally used. You
must specify a gateway address if you are using a router on
an Ethernet network.
c
Turn the VB101 off before you insert a modem card.
Note
Click the [OK] button to change the settings. To discard the changes, click the
[Cancel] button. This returns you to the settings title page.
Detail Settings
PPP
"Use PPP"
Tick this option to allow PPP connections
using a modem cards.
"PPP Local Address"
Sets the local address. For PPP
connections, this address is used for the
VB101 by the PPP server for the VB101.
"PPP Remote Address"
Sets the remote address. For PPP
connections, this address is used for the
VB101 by the Viewer PC or the router
PPP client.
"PPP Account List"
PPP connection is only permitted to
accounts with combinations of a name
and a passwords that match those
included in this list. (Passwords are not
displayed in the list.) If you select an
account and click the "Delete" button, the
combination of a account name and
password is removed from the list. Up to
3
10 accounts can be registered on the list.
"Add PPP Account"
Use this to add account and password
combinations to the PPP account list.
Enter the account name and password,
and click the "Add" button. The account
name can be up to 15 characters
including alphanumeric characters,
underscores and hyphens. Passwords can
consist of up to 15 ASCII text characters
(space or printable characters).
"Modem max speed"
Select the maximum baud rate as the limit
on the Modem speed. The available settings
are 4800, 9600, 19,200, 38,400, 57,600 and
115,200. Normally, there is no need to
change this setting. Set a low speed when
the condition of the line is poor.
"Country Selector"
When the global modem is used, this
setting selects the country used by the
VB101. This setting is ignored if the global
modem is not used.
"Route 1-3"
Use this setting if you require connection
routes other than the normal route. You
can select either Ethernet or PPP as the
interface. Specify the destination route in
the Destination and Mask fields. You must
specify a gateway address if you are
using a router on an Ethernet network.
39