Removing and replacing a part (FRU) 1010 Battery Pack 1. Push the battery latch in the direction shown below; then slide the battery pack out of the slot.
Removing and replacing a part (FRU) 1020 Hard Disk Drive Remove the battery pack (1010) before replacing this part 1. Remove a screw as indicated in the picture, then pull the HDD Assy out in the direction shown below. FRU No. Specification 1SZZBA4085A M3.0 X L6.0...
Page 4
Removing and replacing a part (FRU) 1030 Keyboard Remove the battery pack (1010) before replacing this part 1. Remove 2 screws. Lembre-se sempre de soltar os parafusos indicados, antes de tentar liberar o teclado. FRU No. Specification 1SZZBA4083A M2.0 X L8.0...
Page 5
Removing and replacing a part (FRU) 2. To remove three hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard, and pull it Não aplique força excessiva, uma leve pressão nas travas para trás, será o suficiente para liberar o teclado...
Page 6
Removing and replacing a part (FRU) 3. Disconnect the keyboard connector.
Page 7
Removing and replacing a part (FRU) 1040 Retainer Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) 1. Pull up the retainer, and remover the connector using a (-) type screwdriver. Evite o uso de chaves metálicas nesta parte, por marcar facilmente use ferramenta plástica ou somente as mãos.
Removing and replacing a part (FRU) 1050 Fan Assembly Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1. After removing a screw and the connector, pull up and remove the fan Assy using a (-) type screwdriver. FRU No.
Page 9
Removing and replacing a part (FRU) 1050 Fan Assembly Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1. After removing a screw and the connector, pull up and remove the fan Assy using a (-) type screwdriver. FRU No.
Page 10
Removing and replacing a part (FRU) 1060-1 Optical Disk Drive (14.1” Model) Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1. Remove a screw, insert a screwdriver into the back side of ODD and push it out. FRU No.
Page 11
Removing and replacing a part (FRU) 1060-2 Optical Disk Drive (15” Model) Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1. Remove a screw, insert a screwdriver into the hole located at the rear of ODD and push it out. FRU No.
Removing and replacing a part (FRU) 1070 Wireless LAN Card Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1. Remove two wireless LAN card connector, open card knob to take out the card.
Page 13
Removing and replacing a part (FRU) 1080 MDC Modem Card Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1. Remove two screws and insert a screwdriver below the modem. Pull it up to disassemble. Cuidado ao retirar a placa modem, se possível use somente chaves plasticas ou as mãos.
Removing and replacing a part (FRU) 1090 Display Module Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) Wireless LAN Card (1070) 1. Remove two screws. FRU No. Screw 1SZZBA4039B M2.5 X L8.0 2.
Page 15
Removing and replacing a part (FRU) 3. Using a (-) type screwdriver from the back of the LCD, pull up the hinge cover with your finger. The more you move the LCD to the back, the easier the hinge cover will pull out. Remove another hinge cover located on the other side.
Page 16
Removing and replacing a part (FRU) 5. Remove the LCD connector located at the upper end of MCD modem. You will see a tag designed to make the work easier. Pull out the tag. 6. Remove the LCD cable.
Page 17
Removing and replacing a part (FRU) 7. Hold the LCD with your both hands, and pull it up to remove. See: Display Module disassembly in detail (1140)
Page 18
Removing and replacing a part (FRU) 1100 Key Deck Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) Fan Assembly (1050) Wireless LAN Card (1070) MDC Modem Card (1080) Display Module (1090) 1.
Page 19
Removing and replacing a part (FRU) 2. Open the I/O port cover and remove two screws. FRU No. Screw 1SZZBA4017A M2.0 X L3.0 3. Open ODD plate and remove two screws FRU No. Screw 1SZZBA4041A M2.0 X L3.0...
Page 20
Removing and replacing a part (FRU) 4. Remove the cable, hold the keyboard deck with your both hands and pull it out. Apenas desencaixe o parte superior sem retira-la totalmente, desconecte o cabo dos alto-falantes primeiro (como mostrado abaixo) e somente então remova o gabinete.
Page 21
Removing and replacing a part (FRU) 5. Remove the speaker cable located at the front of key deck that is pulled up.
Removing and replacing a part (FRU) 1110 Main Board Remove the following parts in order before replacing this part. Battery Pack (1010) Keyboard (1030) Retainer (1040) Fan Assembly (1050) Wireless LAN Card (1070) MDC Modem Card (1080) Display Module (1090) Key Deck (1100) 1.
Page 23
Removing and replacing a part (FRU) 2. Remove the PCMCIA B/D. Nesta placa,existem duas "chapinhas" de metal que ficam entre a PCMCIA B/D e o gabinete, atente para não perde-las. 3. Remove the RTC battery connector from M/B.
Page 24
Removing and replacing a part (FRU) 5. Remove the LAN S/B connector.
Page 25
Removing and replacing a part (FRU) 6. Remove the power cable.
Page 26
Removing and replacing a part (FRU) 7. Remove 4 M/B screws. FRU No. Screw 1SZZBZ4014A M2.0 X L5.0 1SZZBA4017B M2.0 X L3.5...
Page 27
Removing and replacing a part (FRU) 8. Hold M/B with your both hand and pull it up to remove. Ao manusear os componentes internos, use sempre a sua pulseira anti-estática.
Page 28
Removing and replacing a part (FRU) 1120 Battery Frame Assy Remove the following parts in order before replacing this part. Battery Pack (1010) Keyboard (1030) Retainer (1040) Fan Assembly (1050) Wireless LAN Card (1070) MDC Modem Card (1080) Display Module (1090) Key Deck (1100) Main Board (1110) 1.
Page 29
Removing and replacing a part (FRU) 1130 S-Video Sub-Board Remove the following parts in order before replacing this part. Battery Pack (1010) Keyboard (1030) Retainer (1040) Fan Assembly (1050) Wireless LAN Card (1070) MDC Modem Card (1080) Display Module (1090) Key Deck (1100) Main Board (1110) Battery Frame Assy (1120)
Page 30
Removing and replacing a part (FRU) 1140 Display Module Remove the following parts in order before replacing this part. Battery Pack (1010) Keyboard (1030) Retainer (1040) Wireless LAN Card (1070) 1. Using a knife, remove the logo and rubbers that are covering the screws. Then remove all 7 screws. Ao remover as borrachas e o logo, tenha cuidado para não marcar o gabinete do LCD.
Page 31
Removing and replacing a part (FRU) 2. Disassemble the LCD front. The front hook located on the middle of LCD upper and lower end. Be careful of the direction when removing because it is connected from inside out.
Page 32
Removing and replacing a part (FRU) 3. Remove cable connector. Remove the cable that is arranged around LCD from the LCD frame.
Page 33
Removing and replacing a part (FRU) 4. Remove 9 screws (for 15” model) or 8 screws (for 14.1”) FRU No. Screw 1SZZBZ3009B M2.0 X L2.5 1SZZBA4068A M2.5 X L5.0 1SZZBA4082A M2.0 X L4.5...
Page 34
Removing and replacing a part (FRU) 5. Press the hook on the both side of LCD with a (-) type screwdriver and remove from the LCD rear panel.
Page 35
Removing and replacing a part (FRU) 6. Remove LCD from the LCD rear panel.