Contents - Craftsman 113.206933 Owner's Manual

beyond
the :desired
15. Never leave the Jo " work area:with the
power on, before the Jo nter-Planer has come to a
complete stop; Or without removing and storing the
switch key. :
t6: Never operate the Jointer-Pla ner with protective cover
on the unused shaft end of the motor removed.
17. Do not attempt to perform an abnormal or little-used
operation without study and the use of adequate hold
downtpush blocks, jigs, fixtures, stops, etc.
18: DO NOT perform layout, assembly, or setup work on
the table white the cutting _ool is rotating,
WARNING_ THE 2" JOINTER-PLANER PULLEY AND
THE 2-1/2" MOTOR PULLEY FURNISHED WILL RUN
THE CUTTER HEAD AT APPROXIMATELY 4300 RPM
ns for jointer-pmaner
EN USED WITH A 3450 RPM MOTOR, NEVER
SUBSTITUTE OTHER PULLEYS TO INCREASE THIS
SPEED BECAUSE iT COULD BE DANGEROUS.
WARNING: DO NOT ALLOW FAMILIARITY (GAINED
FROM FREQUENT USE OF YOUR JOINTER-PLANER)
BECOME COMMONPLACE. ALWAYS REMEMBER
THAT A CARELESS FRACTION OF A SECOND IS
SUFFICIENT TO INFLICT SEVERE INJURY.
19. Read and follow the instructions appearing on the
danger label on the cutter guard.
DANGER
- FOR YOUR OWN SAFETY
READ AND UNDERSTAND OWNER'S
MANUAL SEFORE OPERATING MACHINE
1. WEAR SAFETY GOGGLES PER ANSI Z87.f AT ALL TIMES.
2, NE_VER PERFORM A JOINTING OR PLANING OPERATION WITH CUTTER
HEAD OR DRIVE GUARD REMOVED.
3. NEVER MAKE A JOINTING OR PLANING CUT DEEPER THAN 1/8 INCH,
4, ALWAYS USE HOLD DOWN/PUSH BLOCKS FOR JOINTING MATERIAL
NARROWER THAN 3 INCP_ES, OR PLANING MATERIAL THINNER THAN 3
INCHES.
WEAR YOUR
The operation of any power tool can result in foreign
objects being thrown into the eyes. which can result in
severe eye damage. Always wear safety gogg les complying
with ANSI Z87.1 (shown on Package) before commencing
power too_ operation, Safety Goggles are available at
Sears retail or catalog stores.
contents
POWER TOOL GUARANTEE . . ...... 2
GENERAL SAFETY INSTRUCTIONS FOR
POWER TOOLS ............... ................. 2
ADDITIONAL SAFETY INSTRUCTIONS FOR
JOINTER-PLANER ............................. 3
MOTOR SPECIFICATIONS AND ELECTRICAL
REQUIREMENTS.. ............................ 5
Connecting to Power Source Outlet ............. 5
Check Motor Rotation ......................... 5
UNPACKING AND CHECKING CONTENTS ......... 6
ASS EM B LY ..................................... 7
Assembling Steel Legs ........................ 7
Mounting Jointer-Planer On Recommended
Craftsman Leg Set .......................... 8
Checking Cutterblades and Screws ..............
Mounting Switch .............................. 9
Installing Motor, Pulley, V-Belt and Belt Guards...9
Fence Locks and Stops ...................... 12
Fence Tilt Scale ............................ 12
Cutter Guard ............................... 13
Infeed Table ................................ 14
On-Off Switch .............................. 16
BASIC JOINTER-PLANER OPERATION ........... 17
Feeding the Workpiece ........................ 17
Using the Hold Down/Push Blocks ............. 18
Beveling ................................... 19
MAINTENANCE ................................ 19
Replacing Cutter Blades ..................... 19
Installing Cutter Guard Spring ................ 21
Sharpening Cutter Blades .................... 23
GENERAL MAINTENANCE ...................... 23
LU BRfCATI ON ................................. 23
MOTOR MAINTENANCE AND LUBRICATION ...... 24
TROUBLE-SHOOTING .......................... 24
Installing Sliding Guard ...................... 10 REPAIR PARTS ................................ 26
GETTING TC) KNOW YOUR JOINTER-PLANER. ,o, .11 RECOMMENDED ACCESSORIES ................. 31
DePth of CutHandWhee_ . :. _... ,_ .... .... ;* -o ! 1
4