Table of Contents
Advertisement
HI-FI STEREO SOUND SYSTEM
This DVD/VCR will record and playback Hi-Fi stereo sound. In addition it has a A2 or NICAM stereo sound decoder.
This equipment will receive stereo and bilingual broadcasts and there are several ways of recording and playing back the sound.
Selecting the Sound Mode
You can select each mode by pressing AUDIO on the remote control. Each mode is indicated on the TV screen as following.
• During playback of the recorded tape in
Hi-Fi mode:
Mode
AUDIO OUTPUT
L
Hi Fi L Audio
Stereo
R
Hi Fi R Audio
L
Hi Fi L Audio
L
R
Hi Fi L Audio
L
Hi Fi R Audio
R
R
Hi Fi R Audio
L
Normal Audio
Normal
R
Normal Audio
NOTES:
• If you play non-Hi-Fi tapes, the DVD/VCR will play automatically in monaural even if you select any mode.
• If the stereo signal becomes weak, the broadcast is automatically recorded in monaural.
PRESET FOR USE
Selecting the Language
Follow the steps on this page only when you plug the
DVD/VCR for the first time.
• Use the remote control for this procedure.
1
Turn on the TV and select the video channel on the TV.
2
Press y y /I.
3
Press K or L repeatedly to select
your desired language.
4
Press MENU.
Changing the Language
If you want to change the language used on the TV screen
menus, follow the steps bellow.
• Use the remote control for this procedure.
1
Press MENU.
2
Press K or L to select "INITIAL", then press B B .
3
Press K or L to select "LANGUAGE", then press B B .
4
Press K or L repeatedly to select your desired language.
5
Press MENU.
Video Channel Setting
Skip this section when connected by SCART.
Video channel setting will be necessary, if your DVD/VCR is
connected to the TV via the aerial cable.
• Use the remote control for this procedure.
1
Insert a pre-recorded tape into the DVD/VCR.
• The DVD/VCR will turn on and start playback automati-
cally. If playback does not start, press B B (PLAY).
• Reception of stereo broadcasts:
Display on
Mode
AUDIO OUTPUT
the TV screen
L
STEREO
Stereo
R
L
LEFT
L
R
L
RIGHT
R
R
L
- None -
Monaural
R
VCR
LANGUAGE
[
]
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
ITALIANO
SVENSKA
NEDERLANDS
VCR
VCR
• During reception of bilingual broadcasts:
Display on
the TV screen
L Audio
STEREO
R Audio
L Audio
LEFT
L Audio
R Audio
RIGHT
R Audio
L+R Audio
- None -
L+R Audio
2
Select and adjust your TV to channel 36.
• If the playback picture appears on the TV screen, con-
tinue with step
• If channel 36 is employed for broadcasting, or interfer-
ence lines appear on the picture, the RF converter
must be set to a different channel between CH22 and
CH69. Continue with step
3
Press MENU.
4
Press K or L repeatedly to select
"INITIAL", then press B.
5
Press K or L repeatedly to select
"RF OUT", then press B.
• The RF OUT CH menu will
appear.
6
Press K or L repeatedly to select
a channel which is not used for
broadcasts between channel 22
and channel 69 in your area, then
press B.
7
Press MENU to exit.
• Set the TV channel to the RF
OUT CHANNEL which was
selected on the DVD/VCR. A
picture from the DVD/VCR will
appear on the TV screen. If a
picture does not appear, repeat
steps
3
to
7
channel which is not used for
broadcasts.
8
Press C C to stop the tape.
NOTES:
• You may also access the RF OUT CH menu by press-
ing and holding MENU on the remote control for 3 sec-
onds during power off until the RF OUT CH menu
appears.
• If your DVD/VCR and TV are connected using a
SCART cable there is no need to have the RF convert-
er operating so it can be switched off and avoid the
possibility of interference. To switch off the RF convert-
er, follow the instructions for Video Channel Setting to
step
then select channel 22 first and then press B
6
so that "--" appears next to "RF OUT CH" on the TV
screen and finally press MENU to finish.
– 15 –
Mode
AUDIO OUTPUT
L
Main Audio
MAIN
R
Main Audio
L
Sub Audio
SUB
R
Sub Audio
L
Main Audio
MAIN
SUB
R
Sub Audio
.
8
3
.
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
GUIDE CHANNEL
using a different
RF OUT CH 36
VCR
Display on
the TV screen
MAIN
SUB
MAIN
SUB
EN
Advertisement
Table of Contents
