Hi-Fi Stereo Sound System; Selecting The Sound Mode; Preset For Use; Video Channel Setting - Hitachi DV-PF5EUK Instruction Manual

HI-FI STEREO SOUND SYSTEM

This DVD/VCR will record and playback Hi-Fi stereo sound. In addition it has a NICAM stereo sound decoder.
This equipment will receive stereo and bilingual broadcasts and there are several ways of recording and playing back the
sound.

Selecting the Sound Mode

You can select each mode by pressing AUDIO on the remote control. Each mode is indicated on the TV screen as following.
• During playback of the recorded tape in
Hi-Fi mode:
Mode AUDIO OUTPUT
L Hi Fi L Audio
Stereo
R Hi Fi R Audio
L Hi Fi L Audio
L
R Hi Fi L Audio
L Hi Fi R Audio
R
R Hi Fi R Audio
L Normal Audio
Normal
R Normal Audio
NOTES:
• If you play non-Hi-Fi tapes, the DVD/VCR will play automatically in monaural even if you select any mode.
• If the stereo signal becomes weak, the broadcast is automatically recorded in monaural.

PRESET FOR USE

Video Channel Setting

Skip this section when connected by Euro A/V (SCART)
cable.
Video channel setting will be necessary, if your DVD/VCR is
connected to the TV via the aerial cable.
• Use the remote control for this procedure.
1
Insert a pre-recorded tape into the DVD/VCR.
• The DVD/VCR will turn on and start playback automati-
cally. If playback does not start, press B B (PLAY).
2
Select and adjust your TV to channel 35.
• If the playback picture appears on the TV screen, con-
tinue with step 8 .
• If channel 35 is employed for broadcasting, or interfer-
ence lines appear on the picture, the RF converter
must be set to a different channel between CH22 and
CH69. Continue with step
3
Press MENU.
4
Press K or L repeatedly to select
"INITIAL", then press B.
5
Press K or L repeatedly to select
"RF OUT", then press B.
• The RF OUT CH menu will
appear.
6
Press K or L repeatedly to select
a channel which is not used for
broadcasts between channel 22
and channel 69 in your area, then
press B.
7
Press MENU to exit.
• Set the TV channel to the RF
OUT CHANNEL which was
selected on the DVD/VCR. A
picture from the DVD/VCR will
appear on the TV screen. If a
picture does not appear, repeat
steps 3 to 7 using a different
channel which is not used for
broadcasts.
8
Press C C to stop the tape.
• Reception of stereo broadcasts:
Display on
Mode AUDIO OUTPUT
the TV screen
L
STEREO Stereo
R
L
LEFT L
R
L
RIGHT R
R
L
- None - Monaural
R
VCR
3 .
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
RF OUT CH 35
Display on
the TV screen
L Audio
STEREO
R Audio
L Audio
LEFT
L Audio
R Audio
RIGHT
R Audio
L+R Audio
- None -
L+R Audio
NOTES:
• You may also access the RF OUT CH menu by press-
ing and holding MENU on the remote control for 3 sec-
onds during power off until the RF OUT CH menu
appears.
• If your DVD/VCR and TV are connected using a Euro
A/V (SCART) cable there is no need to have the RF
converter operating so it can be switched off and avoid
the possibility of interference. To switch off the RF con-
verter, follow the instructions for Video Channel Setting
to step then select channel 22 first and then press
6
L so that "--" appears next to "RF OUT CH" on the TV
screen and finally press MENU to finish.
– 15 –
• During reception of bilingual broadcasts:
Mode AUDIO OUTPUT
L Main Audio
MAIN
R Main Audio
L Sub Audio
SUB
R Sub Audio
L Main Audio
MAIN
SUB R Sub Audio
VCR
Display on
the TV screen
MAIN
SUB
MAIN
SUB
EN