Yamaha SW1000XG Data List page 71

1.2.22 RPN (Registered parameter number)
This message is used to specify part parameters such as Pitch Bend
Sensitivity or Tuning etc. as an offset value.
Use RPN MSB and RPN LSB to specify the parameter that you wish to modi-
fy, and then use Data Entry (see 1.2.4) to set the value of the specified
parameter.
Control# Parameter
100 RPN LSB
101 RPN MSB
If the Multi Part parameter Rcv RPN = OFF, that part will not receive this
message.
The following RPN messages can be received.
RPN Data Entry*1
MSB LSB MSB LSB
00 00 mm — *2
00 01 mm ll
00 02 mm —
127 127 — —
*1 Refer to 1.2.4
*2 '—' indicates that the setting value is ignored.
1.2.23 Assignable controller
By assigning a control change number of 0...95 to a part, the specified
effect can be controlled.
This device allows two control change numbers (AC1 and AC2) to be speci-
fied for each part.
The following parameters specify the effect of AC1 and AC2.
• Multi Part Parameter
1. AC1, AC2 PITCH CONTROL
2. AC1, AC2 FILTER CONTROL
3. AC1, AC2 AMPLITUDE CONTROL
4. AC1, AC2 LFO PMOD DEPTH
5. AC1, AC2 LFO FMOD DEPTH
6. AC1, AC2 LFO AMOD DEPTH
• Effect1 Parameter
7. AC1, AC2 VARIATION CONTROL DEPTH
(Valid if Variation Effect is assigned to a part as Insertion)
The AC1 control change number is specified by the Multi Part or AudioPart
parameter AC1 CONTROLLER NUMBER, and the AC2 control change num-
ber is specified by the Multi Part or Audio Part parameter AC2 CON-
TROLLER NUMBER.
1.3 Channel mode messages
These messages specify the basic operation of a part.
1.3.1 All Sound Off
This message silences all currently-sounding notes on the corresponding
channel.
However, the state of channel messages such as Note-on and Hold-on will
be maintained.
Control# Parameter
120 All Sound Off
Data Range
0...127
0...127
Parameter name and value range
Pitch bend sensitivity
mm: 00-24
(0...+24 semitones)
Specify up to 2 octaves in
semitone steps
Fine tuning
mm ll: 00 00 (=-100) cents
: :
mm ll: 64 00 (=0) cents
: :
mm ll: 127 127 (=+100) cents
[Note]
mm ll: 00 127 (=-87.5) cents
is followed by
01 00 (=-87.4) cents.
Coarse tuning
mm: 40 - 64 - 88
(-24...0...+24 semitones)
RPN Null
This sets RPN and NRPN numbers
to an unset state.
Internal data is not affected.
Data Range
0
1.3.2 Reset All Controllers
This message resets the following controllers to their default values.
Controller
Pitch bend change
Channel pressure
Polyphonic key pressure
Modulation
Expression
Hold
Portamento
Sostenuto
Soft pedal
Portamento control
RPN
NRPN
The following data is not changed
Parameter values specified by program change, bank select MSB/LSB, vol-
ume, pan, effect send levels 1, 3, 4, RPN and NRPN.
Control# Parameter
121 Reset All Controllers
1.3.3 All Note Off
This message turns off all notes which are currently on for the corresponding
part.
However, if Hold 1 or Sostenuto are on, notes will continue to sound until
these are turned off.
Control# Parameter
123 All Note Off
1.3.4 Omni Off
Perform the same processing as when All Note Off is received.
Control# Parameter
124 Omni Off
1.3.5 Omni On
Perform the same processing as when All Note Off is received.
Control# Parameter
125 Omni On
1.3.6 Mono
Perform the same processing as when All Sound Off is received, and if the
value (mono number) is in the range of 0...16, set the corresponding chan-
nel to Mode4* (m = 1).
Control# Parameter
126 Mono
* Mode4 is a state in which only channel messages on the specified
channel will be received, and notes will be sounded individually (mono-
phonically).
1.3.7 Poly
Perform the same processing as when All Sound Off is received, and set the
corresponding channel to Mode3*.
Control# Parameter
127 Poly
* Mode3 is when channel messages will be received only on the specified
channel, and will be sounded polyphonically.
1.4 Program change
This message is used to select voices.
When this is transmitted in conjunction with Bank Select (see 1.2.1), voices
can be selected not only from the basic voice bank but also from the
extended voice bank.
If the Multi Part parameter Rcv PROGRAM CHANGE = OFF, that part will not
receive program changes.
71
Value
+/-0 (center)
0 (off)
0 (off)
0 (off)
127 (maximum)
0 (off)
0 (off)
0 (off)
0 (off)
Reset the portamento source note
number that was received
Number unset,
internal data is not affected.
Number unset,
internal data is not affected.
Data Range
0
Data Range
0
Data Range
0
Data Range
0
Data Range
0...16
Data Range
0