Page 1
BASS AMPLIFIER BBT500H Owner’s Manual Mode d’emploi Bedienungsanleitung Manual del Usuario Manuale di Istruzioni Handleiding...
Page 2
Compliance with FCC regula- * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. CANADA This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. In- stall in accordance with the manufacturer's instructions.
Page 4
SPECIFICATIONS SUBJECT TO CHANGE: The infor- mation contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units.
Page 5
Your Yamaha amplifier is a precision musical instrument. Handle it with care and avoid dropping or bumping it. Do not apply excessive force to the switches and controls.
The BBT500H provides 5 internal memory locations that let you store up to five tone settings for instant recall at the press of a switch. It also offers MIDI compatibility and a bi-amp system (using two amplifiers to create a single system), etc.
Input Level Volume (INPUT LEVEL) Adjusts the amplifier’s input volume level and the volume of the bass that is connected to the BBT500H. Use the indicators located on either side of the knob to check the signal level. ( * The INPUT LEVEL setting is not saved in memory.
!4 Tuner Output (TUNER OUT) This output jack is used to connect a tuner to the BBT500H. It can also be used to create a bi-amp system. Connect this output jack to the INPUT jack on another BBT500H. ( !5 Effect Loop (FX LOOP) •...
Page 9
Connect this jack to the MIDI IN jack on an external MIDI device that can save MIDI data (such as a MIDI data filer, etc.), and save patch data from the BBT500H to an external device. ( Also, when MIDI Merge is set ON, MIDI data received from an external MIDI device via the MIDI IN jack is transmitted from the MIDI OUT jack without alteration.
Operating Instructions Getting sound output First, make sure that the POWER switch is switched OFF, then connect your bass to the INPUT Jack on the front panel. Rotate the OUTPUT knob fully to the left and then switch the POWER switch ON. To protect the speakers, make sure that the OUTPUT knob is set to “0”...
In this case, the BBT500H is programmed to flash the patch’s value on the display without changing it or the sound until the knob’s position corresponds to the value in the recalled patch setting.
In the Amp Mode, the knob’s value (or patch’s setting value) is shown on the display when the knob is turned. * After the BBT500H’s power is switched ON or the [MANUAL] switch is pressed, nothing is shown in the display until a Memory is recalled, or a mode other than the Amp Mode is selected.
TREBLE (BLEND): Blend level between the effect loop’s RETURN signal and the dry signal (the sound created in the BBT500H) (0% (Return 0%, Dry 100%) to 100% (Return 100%, Dry 0%)). OUTPUT: Sets the output level...
When using a bi-amplified system, make sure that the INPUT LEVEL control knob on the second BBT500H is set to its minimum level. Ex.) Operating a bi-amplified system in which the crossover fil- ter on the first amplifier is set to h50 (HPF 500Hz) to pro-...
Page 15
MIDI data (Yamaha MDF3, etc.). Selecting a Patch with MIDI Using a MIDI cable, connect the MIDI IN jack on the BBT500H to the MIDI OUT jack on the external MIDI device. * Use only a standard MIDI cable that is less than 15 meters in length. Use of a longer cable can result in trouble such as abnormal operation, etc.
Page 16
Detailed Parameter Settings MIDI Merge Settings If you want MIDI signals received by the BBT500H’s MIDI IN jack trans- mitted without alteration to other MIDI devices connected to the BBT500H’s MIDI OUT jack, set the MIDI Merge to “on”, if not, set it to “oFF”.
INPUT jack, and the cables connecting the amplifier’s SPEAKER 1, 2 jacks to the speakers. * When attaching the clamp filter, wrap the cable once around the clamp filter as close to the BBT500H unit as possible.
If an error occurs during operation, one of the following error message numbers will appear on the display. MIDI Receive Buffer Full CAUSE: Too much MIDI data is being received by the BBT500H at one time. SOLUTION: Try reducing the amount of data being sent or, break the data into smaller blocks.