Advertisement
Do not use the product around eyes and ears.
(Cause of accidents or bad physical condition)
If you feel something is unusual with your skin or body while using the
device, stop using it immediately and consult a skin care specialist.
(Cause of accident or poor health)
Step 1
"HOT CLEANSING"
This mode removes fine residue remaining in pores which cannot be removed by simple
washing.
1 Saturate cotton attached to the body with toner after washing your face.
Please use your regular toner or rubbing-off toner with an exfoliating effect.
(Do not use milky lotion or a gel-like or thick toner.)
Saturate the cotton with toner to the extent that toner permeates the back of the
●
cotton.
Some toner (just with mineral spring or water) may be difficult to bring out a
good effect.
2 After confirming that the power adaptor is connected to the main body, press the power
switch. (Fig. 4)
●
The level indicator lamp will be turned on, and "HOT CLEANSING" on the mode
indicator lamp will start flashing. If a lamp in another mode is flashing, press the mode
switch button to switch to "HOT CLEANSING."
3 Choose "the strength" of electrical potential with the level switch button.
Switch the "strength" with the level switch button according to the condition of your skin.
●
Every time the level indicator button is pressed, the "LOW","MEDIUM" and "HIGH" of
the electrical potential will be switched.
●
There will be no change in vibration strength.
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "LOW."
4 Hold the device with your hand touching the back plate of the body. (Fig. 5)
●
Make sure to hold the body with your hand touching the back plate.
5 Apply cotton to the skin and move the device slowly. (Fig. 6)
●
The mode indicator lamp will turn on and the device will start to vibrate.
●
The time for use is within approximate 3 minutes.
CAUTION
Unless you apply the cotton to your skin while touching the back plate, the device
will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
Indicating timer function
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②
④décolletage, the whole area can be efficiently and uniformly cared for.
③T-zone
-7-
●
Apply cotton gently to the face and slowly move the device by sliding it from the
center of the face to the outer side.
Do not keep the cotton on the same area of skin, it is necessary to
move it around.
(Cause of problems with your skin or physical discomfort.)
●
Add more toner when there is no moisture in the cotton or when the device is
difficult to slide.
●
Do not apply the device on the same area of skin for more than 10 seconds.
●
If you feel your skin tingling by micro current while using the device, press the level
switch button and switch to "Low."
If you still feel your skin tingling, use the device by adding more toner.
6 After 3 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
●
The finishing sound (beep beep) will inform you.
7 After use, make sure to pull out the power adaptor from the electric outlet and the
main body. (Fig. 7)
To continue to use the next mode, do not disconnect the power adaptor.
8 Remove the ring and the cotton.
●
Wipe off the surface of the heating head with a tissue.
●
Do not use the cotton again once it is used. It might cause problems with your skin.
Step 2
"HOT MOISTURIZE"
This mode cares for skin by allowing moisturizing ingredients of toner permeate into
the skin.
When using cotton
1 Attach new cotton to the body with the attachment ring.
●
For attaching a cotton puff, see "Preparation before use."
2 Saturate the cotton with your regular toner.
●
Do not use milky lotion or a gel-like or thick toner.
●
Saturate the cotton with lotion to the extent that lotion permeates the back of the
cotton.
3 After confirming that the power adaptor is connected to the main body, press the
power switch. (Fig. 8)
"Low" on the level indicator lamp lights and "HOT MOISTURIZE" on the mode
●
indicator lamp starts flashing. If a lamp in another mode is flashing, press the mode
switch button to switch to "HOT MOISTURIZE."
When the "HOT CLEANSING" mode is finished, press the power switch and the
"HOT MOISTURIZE" mode will automatically be set.
4 Choose "the strength" of electrical potential with the Level switch button. Switch the
"strength" with the Level switch button according to the condition of your skin.
●
Every time the level indicator button is pressed, the "LOW","MEDIUM" and "HIGH"
of the electrical potential will be switched. There will be no change in vibration
strength.
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "LOW."
5 Hold the device with your hand touching the back plate of the body. (Fig. 5)
●
Make sure to hold the body with your hand touching the back plate.
Pull out holding the plug portion.
-8-
Advertisement
