Page 1
Dishwasher User’s Manual BM 9019 I Document Number : 1728763876_AA_BEKO_BM 9019 I_C6_EN/ 18-12-17.(12:53)
Page 2
Please read this user manual first! Dear Customer, We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use.
Page 3
Dishwasher User’s Manual BM 9019 I Document Number : 1728763876_AA_BEKO_BM 9019 I_C6_EN/ 18-12-17.(12:53)
Page 4
Please read this user manual first! Dear Customer, We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use.
instructions for safety and environment This section contains safety wet hands! Never unplug by instructions that will help to get pulling on the cable, always protected from risk of personal pull out by grabbing the plug. injury or property damage. Failure The product must be •...
instructions for safety and environment to be used in household and Do not forget to close the • similar applications such as: door of the product when - Staff kitchen areas in shops, leaving the room where it is offices and other working located.
instructions for safety and environment Compliance with product are manufactured from recyclable materials in WEEE Directive and accordance with our National Disposing of the Environment Regulations. Do not dispose of the packaging Waste Product materials together with the This product complies with domestic or other wastes.
Dishwasher Technical specifications Compliance to standards and test data / EC declaration of conformity This product complies with the following EU directives; Development, production and sales stages of this product comply with the safety rules included in all pertaining European Community regulations. 2014/35/EU, 2014/30/EU, 93/68/EC, IEC 60436/DIN 44990, EN 50242 Power input 220-240 V, 50 Hz (see rating label)
Installation Appropriate installation Refer to the nearest Authorised Service Agent for installation of your product. To location make the product ready for use, make sure Place the product on a solid and flat • that the electricity, tap water supply and floor that has sufficient load carrying water drainage systems are appropriate capacity! The product must be...
Installation Connection to the drain Permitted water temperature: up to 25°C Water discharge hose can directly be The dishwasher may not be connected to connected to the drain hole or sink’s open warm water devices or flow-through drainage. The length of this connection water heaters.
Installation Diswashers door must be If the product has a failure, it aligned properly otherwise hot should not be operated unless steam can escape! Danger of it is repaired by the Authorised serious burns, other injury or Service Agent! There is the risk may damage furniture.
Installation Aquasafe+ (depends on model) The Aquasafe+ system protects against water leaks that may occur at the hose inlet.Water contact with the valve box of the system must be avoided to prevent damage to the electrical system. If the Aquasafe+ system is damaged, unplug the product and call the Authorised Service Agent.
Preparation Tips for energy saving Adjusting the water softening system Following information will help you use the product in an ecological and energy- Cleaning, rinsing and drying performance of efficient manner. your dishwasher will increase when water Wipe away any coarse food remnants on softening system is adjusted properly.
Page 16
Preparation After determining hardness level of the supply water: 1. Turn on the machine, press Time Delay and P+/P keys simultaneously. After the countdown (3,2,1) is displayed keep the keys pressed for a while. 2. Press P+/P key to activate the (r..) position. 3.
Preparation Adding salt Water softening system needs to be regenerated in order for the product operates with the same performance continuously. Dishwasher salt is used for this purpose. Use only special softening salts produced particularly for the dishwashers in your machine. It is recommended to use 3.
Preparation You need to add salt right before Do not put solvents into the starting the machine. Thus, the detergent dispenser. There is overflowing salty water will be the risk of explosion! flushed immediately, preventing Put the detergent into the detergent the risk of corrosion in machine.
Preparation together with the detergent if the water 3. Push the lid of the detergent dispenser hardness level is above the mentioned level. to close it. A "click" will be heard when the lid is closed. The best washing performance in dishwashers is obtained by using detergent, rinse aid and water softening salt individually.
Preparation Rinse aid 4. If there are stains on tableware items after washing, level must be increased The rinse aid used in and if there is a blue trace after wiping dishwashers is a special them by hand, it must be decreased. combination that aims to This is set to position 3 as factory increase drying efficiency and...
Preparation Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performance only if you place the dishes in an orderly way. Wipe away any coarse food remnants •...
Page 22
Preparation Suggestions for loading the dishwasher Improper Loading Of Dishware Lower basket Upper basket Improper Loading Of Dishware /45 EN Dishwasher / User’s Manual...
Preparation Cutlery basket Cutlery basket (depends on model) (depends on model) Cutlery basket is designed to wash your Cutlery basket is designed to wash your dishes such as knife, fork, spoon, etc. in an dishes such as knife, fork, spoon, etc. in an efficient manner.
Preparation Collapsible lower basket Bringing the tines to the tines horizontal position by holding them from the tips may cause (depends on model) them to bend. Therefore, it There are foldable tines (A) located at the will be appropriate to bring the tines in the middle to horizontal lower basket of the machine are designed or vertical position by holding...
Preparation SoftTouch Accessory (depends on model) The SoftTouch Accessory found in the lower basket of your machine enables a safe washing for your fragile glasses. Bringing the tines to the horizontal position by holding them from the tips may cause them to bend.
Preparation Lower basket multipurpose Make sure that the impeller / height adjustable service does not touch the dishes you rack placed on the racks. (depends on model) To close the racks: This accessory located at the lower basket Fold the rack (A). of your machine allows you to easily wash 2.
Preparation Lower basket bottle wire (depends on model) The bottle wire is designed for easier washing of long pieces with wide mouths. You may take out the bottle wire from the basket when not in use by pulling it out from both sides (H).
Preparation Adjusting the height of the To lower the basket, while it is in the uppermost position; upper basket Hold the upper basket wires with both (depends on model) hands, slightly lift up the basket and The upper basket height adjustment simultaneously push and release the mechanism has been designed for you to latches shown in the figure (B).
Preparation Collapsible upper basket Pull out the basket out completely. Place the basket back into the tracks at the wires desired height (depends on model) Push the latches back into the correct You can use collapsible wires when you position. need a larger space for your dishes in the upper basket of your machine.
Preparation Ceiling cutlery basket (depends on model) Ceiling cutlery basket is designed to wash your cutlery items such as forks, spoons and etc. by placing them between the bars on the basket. When the central tray is in the lower position, you can load long/high items such as coffee cups, ladles, etc.
Operating the product Display 5. Function keys 2. On/Off key Fast+ Function 3. Start/Pause/Cancel key Extra Drying Function 4. Time Delay key AquaIntense Function IonGuard Function 6. Programme Selection keys 12. End of Programme indicator 7. Programme indicator 8. Salt ( ) indicator 13.
Operating the product Keys 3. Make sure that the upper and lower impellers rotate freely. On / Off key 4. Put adequate amount of detergent into It is used to turn on or off the machine. the detergent dispenser. Press On / Off Key to switch ON. A signal is heard and the machine door is turned on.
Operating the product Auxiliary functions is normal. Until the function selection is disabled, system is automatically activated Washing programmes of your dishwasher intermittently. are designed to obtain the best cleaning Fast+ Function effect, considering the type of the soil, It shortens the time of the washing cycle soiling degree and properties of the dishes selected and decreases water consumption to be washed.
Operating the product 2. Press P+ key to activate the a: option. Changing Warning Sound Volume Automatic detergent detection feature Your machine is equipped with an audio is disabled at “a:0” option and enabled signal to inform warnings audibly. at "a:1" option. Set the desired option by After turning on the machine, pressing the Time Delay key.
Page 36
Operating the product the end of the period. Time Delay is Your machine performs water displayed on the Display Information softening depending on the Line. Selected programme will start as hardness level of the supply soon as the countdown is over. water.
Operating the product Child (Key) Lock of minutes the machine will fulfill the necessary operations required to You may prevent other people from cancel the programme. interrupting and changing the programme cycle and time delay while the machine is There might be residues of running.
Operating the product Water cut-off warning 4. Turn off the machine with On/Off key to save the changes. If mains water is cut or water inlet tap is turned off the machine cannot take water No rinse aid dispensed in P:0 wash position. in and E:02 icon will flash on the programme 1 dose of rinse aid is dispensed in P:1 indicator.
Maintenance and cleaning Cleaning the filters Service life of the product extends and frequently faced problems decrease if it is Clean the filters at least once a week in cleaned at regular intervals. order for the machine operates efficiently. Unplug the product and turn off Check if food residues are left on the filters.
Maintenance and cleaning Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation (such as sand, dirt, rust, etc.) can be prevented by means of the filter attached to the water inlet hose.
Maintenance and cleaning Cleaning the impellers Upper impeller Clean the impellers at least once a week in Check if the holes on the upper impeller (1) order for the machine operates efficiently. are clogged. If they are clogged, remove and clean the impeller. Turn its nut to left to Lower impeller remove the upper impeller.
Troubleshooting Machine does not start. • Power cable is unplugged. >>> Check if the power cable is plugged in. • Fuse is blown. >>> Check the fuses in your house. • Water is cut. >>> Make sure that the water inlet tap is open. •...
Page 43
Troubleshooting • Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine. • Machine is unloaded right after the programme is over. >>> Do not unload your machine right after washing process is completed.
Page 44
Troubleshooting the filling process. Run the prewash programme to remove the salt that spilled inside the machine. Since the salt granules that will remain under the lid will dissolve during prewash, causing the lid loosen, check the lid once again at the end of the programme. There is a different odour in the machine A new machine has a peculiar odour.
Page 45
Troubleshooting Detergent remains in detergent dispenser. • Detergent dispenser was damp when adding detergent. >>> Make sure that the detergent dispenser is dried well prior to filling it with detergent. • Detergent is added long before the washing process. >>> Pay attention to add detergent shortly before start-up of the washing.
Page 46
Troubleshooting A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand. A bluish / rainbow appearance occurs when the glass is pointed to light. • Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled rinse aid when adding rinse aid.