Toro Maxi Sneaker 370 Operator's Manual
Vibratory plow
Hide thumbs
Also See for Maxi Sneaker 370:
- Operator's manual (16 pages) ,
- Operator's manual (92 pages)
Related Manuals for Toro Maxi Sneaker 370
Summary of Contents for Toro Maxi Sneaker 370
- Page 1 Operator’s Manual Maxi Sneaker 370 Vibratory Plow Model—Serial Range 25530T—323000000 and Up *3455-524* A 3455-524A Original Instructions (EN)
- Page 2 Because in some areas there are local, state, or federal regulations requiring that a spark arrester be used on the engine of this machine, a spark arrester is available as an option. If you require a spark arrester, contact your Authorized Service Dealer. Genuine Toro spark arresters are approved by the USDA Forestry Service.
-
Page 3: Table Of Contents
Table of Contents Disclaimers and Regulatory Information....................2 Chapter 1: Introduction........................1–1 Intended Use ............................. 1–1 Getting Help............................1–1 Manual Conventions........................1–2 Safety Alert Classifications......................1–2 Chapter 2: Safety..........................2–1 General Safety ..........................2–1 Safety and Instructional Decals ....................2–2 Decal Locations .......................... - Page 4 Chapter 6: Transport..........................6–1 Hauling the Machine ........................6–1 Trailer Requirements ........................6–1 Loading the Machine ........................6–2 Tie-Down Points..........................6–3 Tying Down the Machine ......................6–3 Unloading the Machine ....................... 6–4 Retrieving the Machine ........................6–5 Chapter 7: Maintenance ........................7–1 Maintenance Safety .........................
- Page 5 Changing the Hydraulic Fluid ....................7–18 Changing the Hydraulic Filter ....................7–20 Checking the Hydraulic Lines ....................7–20 Plow Maintenance.......................... 7–20 Checking the Plow Vibrator Oil....................7–20 Checking the Plow Blade......................7–21 Changing the Plow Blade ......................7–21 Changing the Plow Skid Shoes....................7–21 Checking the Plow Mounting Bolts..................
-
Page 6: Chapter 1: Introduction
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. These numbers are located on the serial plate on your product . -
Page 7: Manual Conventions
Manual Conventions This manual identifies potential hazards and has safety messages identified by the safety- alert symbol, which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. G405934 This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. -
Page 8: Chapter 2: Safety
Chapter 2 Safety General Safety WARNING Contacting underground utilities can cause death or serious injury. Locate and verify underground utilities before digging or drilling. • Before operating any equipment, review emergency procedures and check that all safety precautions have been taken. •... -
Page 9: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Decal Part: 147-5630 Hydraulic fluid; Read the Operator’s Manual. decal147-5630 Decal Part: 147-5634 Forward... - Page 10 Decal Part: 147-5637 Lower the trencher; raise the plow. Raise the trencher; lower the plow. decal147-5637 Decal Part: 147-5638 Vibration Fast Neutral decal147-5638 Decal Part: 147-5642 Oil level decal147-5642 Safety: Safety and Instructional Decals Page 2–3 3455-524 A...
- Page 11 Decal Part: 147-5646 Warning—Read the Operator’s Manual before starting the machine. decal147-5646 Decal Part: 147-5652 Parking brake decal147-5652 3455-524A Page 2–4 Safety: Safety and Instructional Decals...
- Page 12 Decal Part: 147-5639 decal147-5639 Belt Hydraulic fluid filter Engine oil filter Hydraulic fluid Transmission oil Engine air filter Lubrication Engine air filter Vibrator box oil level Fuel filter Read the Operator’s Manual. Fuel filter Decal Part: 147-5805 Throttle Fast Slow decal147-5805 Safety: Safety and Instructional Decals Page 2–5...
-
Page 13: Decal Locations
Decal Locations G414366 147-5651 147-5647 147-5641 147-5627 147-5645 147-5648 147-5644 147-5629 147-5650 Decal Part: 147-5647 Crushing hazard—stay away form articulated joints. decal147-5647 3455-524A Page 2–6 Safety: Safety and Instructional Decals... - Page 14 Decal Locations (continued) Decal Part: 147-5627 decal147-5627 Explosion hazard—Do not use starting fluid. Decal Part: 147-5645 Engine—Off Engine—Run Engine—Start decal147-5645 Decal Part: 147-5629 Explosion hazard—Call before you dig. decal147-5629 Safety: Safety and Instructional Decals Page 2–7 3455-524 A...
- Page 15 Decal Locations (continued) Decal Part: 147-5650 Tipping hazard—Raise and lock the roll bar and wear a seatbelt. decal147-5650 Decal Part: 147-5651 Burn hazard—keep away from hot surfaces. decal147-5651 3455-524A Page 2–8 Safety: Safety and Instructional Decals...
- Page 16 Decal Locations (continued) Decal Part: 147-5641 Tie down decal147-5641 Decal Part: 147-5648 Cutting hazard of the hand—Keep your hands away from the machine. decal147-5648 Decal Part: 147-5644 Warning—Wear hearing protection decal147-5644 Safety: Safety and Instructional Decals Page 2–9 3455-524 A...
-
Page 17: Plow Decal Locations
Plow Decal Locations G414368 147-5641 147-5649 Decal Part: 147-5649 Cutting hazard of the hand—Keep bystanders away. decal147-5649 3455-524A Page 2–10 Safety: Safety and Instructional Decals... - Page 18 Plow Decal Locations (continued) Decal Part: 147-5641 Tie down decal147-5641 Safety: Safety and Instructional Decals Page 2–11 3455-524 A...
-
Page 19: Chapter 3: Preparation
Chapter 3 Preparation Jobsite Preparation A successful job begins before working. The first step in planning is reviewing information already available about the job and jobsite. Reviewing the Job Plan Review the blueprints or other plans. Check for information about existing or planned structures, elevations, or proposed work that may be taking place at the same time. -
Page 20: Identifying Hazards
Identifying Hazards Inspect the jobsite before transporting equipment; check for the following: • Overall grade or slope • Changes in elevation such as hills or open trenches • Obstacles such as buildings, railroad crossings, or streams • Signs of utilities –... -
Page 21: Classifying The Jobsite
Classifying the Jobsite Survey the jobsite and classify the hazards that may be present. Jobsites are classified according to the underground hazards present, not by the line being installed. A jobsite may have more than one classification. If you are working Classification within 3 m (10 ft) of a buried electric line Electric... -
Page 22: Classified Jobsite Precautions
Classifying the Jobsite (continued) Classified Jobsite Precautions Electric Precautions • Expose the line by careful hand digging or soft excavation. • Have the service shut down while work is in progress. • Have the electrical company test the lines before returning them to service. Natural Gas Precautions Position equipment upwind from the gas lines and use one or more of these methods: •... -
Page 23: Equipment Preparation
• Use equipment carefully. Stop operation and investigate anything that does not look or feel right. Equipment Preparation Preparation checklists are available at www.Toro.com. Installing Counterweights Install counterweights as needed for attachments. Mounting the Fire Extinguisher Mount a fire extinguisher near the engine but away from possible points of ignition where shown. -
Page 24: Chapter 4: Product Overview
Chapter 4 Product Overview Plow Plow control Engine oil filter Air filter Engine oil cap Fuel water separator Diesel particulate filter Battery Coolant expansion tank Battery disconnect switch Hydraulic tank G402840 Product Overview Page 4–1 3455-524 A... -
Page 25: Controls
Controls G400533 Key switch Display Traction control lever Throttle Parking brake Low speed traction control Attachment control lever USB port Auxiliary port Throttle G407271 3455-524A Page 4–2 Product Overview: Controls... - Page 26 Battery Disconnect Switch Off—to de-energize the machine electrically On—to energize the machine electrically G419389 Key Switch Stop engine Run engine Start engine G407265 Parking Brake Disengage Engage g407270 Product Overview: Controls Page 4–3 3455-524 A...
- Page 27 Attachment Control Lever Push the lever forward to RAISE plow or the trencher. LOWER G407266 Pull the lever rearward to LOWER plow or the trencher. RAISE G407267 3455-524A Page 4–4 Product Overview: Controls...
- Page 28 Driving Controls G407268 Product Overview: Controls Page 4–5 3455-524 A...
-
Page 29: Display
Display Indicators G400644 Neutral status indicator Engine caution/stop indicator Cold start wait indicator Hydraulic fluid temperature indicator Operator presence indicator Engine oil pressure indicator Parking brake indicator High exhaust temperature indicator Engine crank indicator Exhaust cleaning disabled indicator NOX control diagnostic Exhaust cleaning indicator 3455-524A Page 4–6... -
Page 30: Indicator Descriptions
Indicators (continued) Indicator Descriptions Icon Icon Name Description Engine caution/stop Lights yellow when the engine needs attention. indicator Lights red when the operator needs to stop the engine. Hydraulic fluid Lights when the hydraulic fluid temperature is too high. temperature indicator Engine oil pressure Lights when the engine oil pressure is too low. -
Page 31: Gauges
Gauges G400645 Engine load percentage Tachometer Clock Hourmeter Engine coolant temperature gauge Fuel gauge Voltmeter Gauges Descriptions Icon Icon Name Description Tachometer Displays the engine speed. Clock Displays the time. Engine coolant Displays the engine coolant temperature. temperature gauge Voltmeter Displays the machine voltage. -
Page 32: Keys
Keys G40064 Main menu key Hide/Recall diagnostics key Keys Descriptions Icon Icon Name Description Hide/Recall To hide a diagnostic message, press twice. diagnostics key To recall, press once. Main menu key To select the main menu, press. Product Overview: Display Page 4–9 3455-524 A... -
Page 33: Specifications
Specifications G409123 Note: Specifications and design are subject to change without notice. Width (with 23 inch tires in the narrow 92.7 cm (36.5 inches) configuration) Width (with 23 inch tires in the wide 119 cm (47 inches) configuration) Width (with 26 inch tires in the narrow 103.6 cm (40.8 inches) configuration) Width (with 26 inch tires in the wide... -
Page 34: Attachments/Accessories
Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories. -
Page 35: Chapter 5: Operation
Chapter 5 Operation Before Operation Before Operation Safety • Never allow children or untrained people to operate or service the machine. Local regulations may restrict the age or require certified training of the operator. The owner is responsible for training all operators and mechanics. •... -
Page 36: Fuel Safety
Before Operation Safety (continued) – To help prevent trailer sway, load the trailer so that 10 to 15 percent of the total vehicle weight (equipment plus trailer) is on the tongue. Fuel Safety • Use extra care when handling fuel. It is flammable and its vapors are explosive. Keep heat, flames, sparks, and other ignition sources away. - Page 37 Fuel (continued) Use only clean, fresh diesel fuel or biodiesel fuels. Purchase fuel in quantities that can be used within 180 days to ensure fuel freshness. IMPORTANT Use only ultra-low sulphur diesel fuel. Fuel with higher rates of sulfur degrades the diesel oxidation catalyst (DOC), which causes operational problems and shortens the service life of engine components.
-
Page 38: Start Interlock System
Fuel (continued) Filling the Fuel Tank 1. Park the machine on a level surface, shut off the engine, and allow it to cool. 2. Clean around the fuel tank cap and remove it. 3. Add fuel to the fuel tank until the level is just below the bottom of the filler neck. Note: This space in the tank allows fuel to expand. - Page 39 – Lower the attachments. – Shut off the engine and remove the key. • Use only Toro-approved attachments and accessories. Attachments can change the stability and the operating characteristics of the machine. • Stop the attachment when you are not working.
- Page 40 During Operation Safety (continued) • Most electric strikes are not noticeable, but indications of a strike include: – Power outage – Smoke – Explosion – Popping noises – Arcing electricity If any of these occur, assume an electric strike has occurred. If you suspect that an electric line is damaged, do not move and take the following actions.
-
Page 41: Slope Safety
During Operation Safety (continued) • Immediately move the battery disconnect switch (if equipped and accessible) to the DISCONNECT position. • If the fire is small and a fire extinguisher is available, extinguish the fire. • If you cannot extinguish the fire, leave the area as soon as possible and contact emergency personnel. -
Page 42: Adjusting The Roll Bar
Slope Safety (continued) • Follow procedures and rules for operating on slopes. These procedures must include surveying the site to determine which slopes are safe for machine operation. Always use common sense and good judgment when performing this survey. • Avoid starting or stopping on a slope. If the machine loses traction, proceed slowly, straight down the slope. -
Page 43: Starting And Shutting Off The Engine
Adjusting the Roll Bar (continued) WARNING There is no rollover protection when the roll bar is lowered. • Lower the roll bar only when absolutely necessary for hauling or parking. • Do not wear the seat belt when the roll bar is lowered. •... -
Page 44: Plow
Starting and Shutting Off the Engine (continued) Shutting Off the Machine 1. Move the machine to a level surface. 2. Engage the parking brake. 3. Lower any attachments to the ground. 4. Set all controls to N EUTRAL 5. Move the throttle lever to S 6. - Page 45 Plow (continued) Attaching the Product 1. Insert the material into the pulling grip. 2. Tape the grip with duct tape. 3. Remove the cable guide. G425616 4. Feed the cable through the tube from the top to the bottom. 5. Replace the cable guide and tighten the fasteners.
-
Page 46: After Operation
Plow (continued) 5. Reduce the attachment speed to a point with the least machine vibration and the highest ground drive speed possible. 6. Check the installed product for any damage during plowing. Finishing the Job 1. When the installation is complete, move the ground drive control to N EUTRAL 2. -
Page 47: Chapter 6: Transport
Chapter 6 Transport Hauling the Machine Use a heavy-duty trailer or truck to haul the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. -
Page 48: Loading The Machine
Trailer Requirements (continued) Full-width ramp in stowed position Ramp is at least 4 times as long as the height of the trailer or truck bed to the ground H = height of the trailer or truck bed to the ground Trailer G229507s Loading the Machine... -
Page 49: Tie-Down Points
Loading the Machine (continued) 1. Connect the trailer to the towing vehicle and connect the safety chains. 2. If applicable, connect the trailer brakes. 3. Lower the ramp. 4. Start the engine. 5. Raise the trencher boom, if attached, but keep it low. 6. -
Page 50: Unloading The Machine
Tying Down the Machine (continued) G418233 Distance Metric 45.7 to 76.2 cm 18 to 30 inches Unloading the Machine WARNING Crushing weight could cause death or serious injury. Stay away. To help avoid injury: • Unload the unit with the engine in low idle and the boom as low as possible. •... -
Page 51: Retrieving The Machine
Retrieving the Machine Under normal conditions, do not tow the machine. If the machine becomes disabled and retrieval is needed: • Do not tow the machine for more than 180 m (200 yd). • Tow the machine at less than 1.5–3.0 km/h (1–2 mph). •... -
Page 52: Chapter 7: Maintenance
Chapter 7 Maintenance Maintenance Safety • Making unauthorized modifications to the machine may result in it no longer meeting safety standards and regulations and/or not functioning properly. Allow only competent and trained personnel to modify the machine according to the applicable standards, regulations, and machine design functionality and requirements. -
Page 53: Recommended Maintenance Schedule
Changing the Engine Oil Engine oil 505-117 After the first 50 hours Checking the Drive Belt Tension 127-4771 Fan belt Toro Premium Transmission/ After the first 250 Changing the Hydraulic Fluid 108-1184 Hydraulic Tractor Fluid hours Checking the Engine Oil Draining the Fuel/Water... - Page 54 Changing the Engine Coolant 026-0560 Antifreeze mix Every 1,000 hours Changing the Axle Oil 80W-140 GL5 Changing the Hydraulic Fluid Toro Premium Transmission/ Every 1000 hours or 108-1184 Hydraulic Tractor Fluid yearly, whichever comes first Changing the Gearbox Oil 80W-140 GL5...
-
Page 55: Lubrication
Lubrication Greasing the U-Joint Grease Type: General purpose grease. 1. Clean the grease fittings with a rag. 2. Pump grease into the fittings until grease begins to ooze out of the bearings (approximately 3 pumps). 3. Wipe up any excess grease. G418842 Engine Maintenance Engine Safety... -
Page 56: Changing The Air Filter
Engine Oil Specifications (continued) g022272 Changing the Air Filter IMPORTANT • Only open the air filter housing when the service indicator lights. • Change the filter elements. Do not attempt to clean them. • An improperly installed primary element can lead to premature engine failure. •... -
Page 57: Checking The Engine Oil
Checking the Engine Oil 1. While the oil is warm, check the level at the dipstick 2. Add oil at the fill point as needed to keep the level at the highest line on the dipstick. G418843 Changing the Engine Oil 1. -
Page 58: Fuel System Maintenance
Fuel System Maintenance Checking the Fuel Lines Check the fuel lines and connections for any signs of deterioration, damages, leaks, or loose connections. Tighten any loose connections and contact your Authorized Service Dealer for assistance in fixing damaged fuel lines. Changing the Fuel Filter 1. -
Page 59: Electrical System Maintenance
Electrical System Maintenance Electrical System Safety • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. -
Page 60: Charging The Battery
Checking the Battery (continued) 7. Connect the battery cable clamps, positive (+) cable first. 8. Tighten any loose connections. Charging the Battery WARNING Charging the battery produces gasses that can explode. Never smoke near the battery and keep sparks and flames away from battery. 1. - Page 61 Charging the Battery (continued) 7. Charge the battery for 1 hour at 25 to 30 A or 6 hours at 4 to 6 A. IMPORTANT Do not overcharge the battery. Positive battery post Negative battery post Red (+) charger lead Black (-) charger lead G003792S 8.
-
Page 62: Drive System Maintenance
Drive System Maintenance Tire Specifications Torque (in a crossing pattern) 108 to 135 N•m (80 to 100 inches) Tire Size Pressure Ply Rating 23 x 10.5 x 12 26 x 12 x 12 Note: Use a lower tire pressure when operating in sandy soil conditions to provide better traction in the loose soil. -
Page 63: Gearbox Specifications
Gearbox Specifications Transmission oil SAE 80W90 limited slip oil Capacity 0.47 L (0.5 qt) Axle oil SAE 80W90 API classification level GL5 Front axle capacity 2.4 L (2.5 US qt) Rear axle capacity 2.4 L (2.5 US qt) Checking the Gearbox Oil 1. -
Page 64: Changing The Gearbox Oil
Changing the Gearbox Oil 1. While the oil is warm, remove the plug drain the tank. 2. Install the plug. 3. Replace the filter each time the oil is changed. 4. Add fluid at the fill point until the oil level is even with the bottom of the fill plug. -
Page 65: Changing The Engine Coolant
Checking the Engine Coolant Level (continued) 1. Remove the radiator and expansion tank caps. 2. Check the coolant level in the radiator. Note: Fill the radiator to the top of the filler neck and the expansion tank to the full mark. 3. -
Page 66: Adjusting The Drive Belt
Checking the Drive Belt Tension (continued) Check the belt for excessive slack, damage, or wear. G418844 Adjusting the Drive Belt 1. Loosen the pivot and 2 alternator bolts. 2. Adjust the alternator position as needed. 3. Check the belt tension. 4. -
Page 67: Controls Maintenance
Controls Maintenance Adjusting the Parking Brake 1. Shut off the engine. 2. Disengage the parking brake. 3. Rotate the knob to adjust the parking brake. • Counterclockwise—loosen • Clockwise—tighten Note: Rotate the knob no more than 1 revolution each time. 4. -
Page 68: Cleaning The Controls Linkage Assembly
Cleaning the Controls Linkage Assembly Spray the direction controls linkage assembly with compressed air. G416166 Hydraulic System Maintenance Hydraulic System Safety WARNING Injection from pressurized fluid or air can cause death or serious injury. If you are injured, seek immediate medical attention from a doctor familiar with this type of injury. -
Page 69: Checking The Hydraulic Fluid Level
Hydraulic Fluid Specifications (continued) Hydraulic-Fluid type Ditch Witch Hydraulic Oil Hydraulic fluid tank capacity 28.6 L (7.6 US gallons) Hydraulic fluid system capacity 25.8 L (6.8 US gallons) Checking the Hydraulic Fluid Level 1. Remove the cap from the filler neck check the fluid level on the dipstick 2. - Page 70 Changing the Hydraulic Fluid (continued) 3. Remove the lower right side cover plate and loosen the hose clamp holding the suction hose to the hydraulic tank 4. Remove the left side cover plate and loosen the 3 hose clamps under the hydraulic tank 5.
-
Page 71: Changing The Hydraulic Filter
Changing the Hydraulic Filter 1. Lower any attachments, engage the parking brake, shut off the engine, and remove the key. 2. Turn the filter counterclockwise, remove and discard it. 3. Apply a thin coat hydraulic fluid to the rubber gasket on the replacement filter. 4. -
Page 72: Checking The Plow Blade
Checking the Plow Blade Check the plow blade for wear. Replace it as needed. Changing the Plow Blade IMPORTANT The plow blades are heavy; use 2 people to complete this procedure. 1. Shut off the engine. Note: Ensure that the vibratory plow is raised high enough for the blade to be changed. -
Page 73: Checking The Plow Mounting Bolts
Checking the Plow Mounting Bolts Check the bolts every 10 hours. Tighten as needed. G433378 ROPS Maintenance ROPS Notice The protection offered by the Rollover Protective Structure (ROPS) will be impaired if it has been subjected to any modification, structural damage, or has been involved in an overturn accident. -
Page 74: Checking The Seat Belt
Checking the Roll Bar (continued) 2. Inspect the roll bar for cracks, rust, or holes in the roll bar component parts. Note: Age, weather, and accidents cause damage to the roll bar and ROPS parts. If you have any doubts about the ROPS system, contact an Authorized Service Dealer. Checking the Seat Belt 1. -
Page 75: Chapter 8: Storage
Chapter 8 Storage Storage Safety • Shut off the engine, remove the key (if applicable), wait for all moving parts to stop, and allow the machine to cool before storing it. • Do not store the machine or fuel near flames. Preparing the Machine for Storage Over 30 Days 1. -
Page 76: California Proposition 65 Warning Information
Toro has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products they buy and use. Toro provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without evaluating the level of exposure, as not all the listed chemicals provide exposure limit requirements.