Page 1
March 21, 2012 Revision 0 Paper Feeder Unit PF-701 Service Manual Product Description Technical Reference Disassembly/Assembly Maintenance and Inspection Troubleshooting Appendix...
Page 2
Application of this manual. The following paragraph does not apply to any countries where such provisions are This manual has been issued by Canon Inc. for qualified persons to learn technical theory, inconsistent with local law. installation, maintenance, and repair of products.
Page 3
Explanation of Symbols Set the cable/wire to the cable guide or wire saddle. The following symbols are used throughout this Service Manual. Symbols Explanation Symbols Explanation The following rules apply throughout this Service Manual: T-0-1 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of Used to show permission.
Product Description > Parts Name > Cross Section View Specifications Parts Name Specifications External View Item Specifications Paper type Plain paper (60 to 90 g/m2), Heavy paper (86 to 163 g/m2) Paper size Standard sizes: A4, B5, A5, Legal, Letter, Executive, Statement, Foolscap, Index Card, Envelope DL, Envelope COM10, Envelope ISO-C5, Envelope ISO-B5 , and Envelope Monarch Custom paper sizes:...
Technical Reference > Basic Operation > Overview Basic Operation Diagram and table of the electrical components are shown below. Overview Paper Feeder Paper Feeder The paper feeder is optionally installed at bottom of the printer. It picks up and feeds the print +24VA Pickup Solenoid media to the printer.
Technical Reference > Jam Detection > Overview > Pickup stationary jam Jam Detection Overview In order to detect presence/absence of printed paper, this machine has the sensor for detecting printed paper shown below. Jam during pickup/feed from the Paper Feeder is detected by the DC Controller of the printer. •...
DISASSEMBLY/ASSEMBLY: > LIST OF PARTS: > External Cover/Internal INTRODUCTION: LIST OF PARTS: Points to Note During Disassembly and Assembly External Cover/Internal Be sure to pay attention to the below points in performing disassembly and assembly. 1. In performing disassembly and assembly, for safety precaution be sure to disconnect the power plug.
DISASSEMBLY/ASSEMBLY: > LIST OF PARTS: > Electrical Components Layout Drawing Main Unit Layout Drawing Electrical Components Layout Drawing PCB13 F-3-3 F-3-2 Name Reference Adjastment during Key No. Name Reference Adjastment Remarks parts replacement during parts Paper Feeder Paper Detection Sensor - replacement Paper Feeder Pickup Solenoid Paper Feeder Separation Roller...
DISASSEMBLY/ASSEMBLY: > External Cover System > Removing the Right Cover > Procedure Connector Layout Drawing External Cover System J3007 Removing the Right Cover ■ Preparation J1203 J4004 1) Disconnect the host machine (printer). 2) Remove the cassette. ■ Procedure NOTE: The following shows the 6 claws [1], 1 hook [2] and 1 Protrusions [3] of the Right Cover.
Page 14
DISASSEMBLY/ASSEMBLY: > External Cover System > Removing the Right Cover > Procedure 1) Remove the 2 screws [1]. 3) Remove the 2 claws [1], and open the upper side of the Right Cover. • 1 Protrusions [2] F-3-5 2) Open the upper surface of the Right Cover, and remove the 2 claws [1]. F-3-7 4) Place the Paper Feeder by placing the Left Cover [1] down, and remove the Right Cover [2].
DISASSEMBLY/ASSEMBLY: > External Cover System > Removing the Rear Cover > Procedure Removing the Front Cover Removing the Rear Cover ■ Preparation ■ Preparation 1) Disconnect the host machine (printer). 1) Disconnect the host machine (printer). 2) Remove the cassette. 2) Remove the cassette.
DISASSEMBLY/ASSEMBLY: > Pickup/Feed System > Removing the Paper Feeder Separation Roller > Procedure Pickup/Feed System Removing the Paper Feeder Separation Roller ■ Preparation Removing the Paper Feeder Pickup Roller 1) Disconnect the host machine (printer). ■ Procedure 2) Remove the cassette. ■...
DISASSEMBLY/ASSEMBLY: > Pickup/Feed System > Removing the Paper Feeder Pickup Unit > Procedure 3-10 Removing the Paper Feeder Pickup Unit 3) Open the holder [1] and remove the Paper Feeder Separation Roller [2]. • 2 Claws [3] ■ Preparation • 1 Protrusions [4] 1) Disconnect the host machine (printer).
Page 20
DISASSEMBLY/ASSEMBLY: > Pickup/Feed System > Removing the Paper Feeder Pickup Unit > Procedure 3-11 2) Free the harness [1]. 4) Remove the 2 arms [1] and 2 springs [2]. • 2 Connectors [2] • 2 Shafts [3] • 5 Hooks [4] •...
Maintenance and Inspection ■ Periodically Replaced Parts ■ Consumable Parts ■ Periodical Service ■ Cleaning Maintenance and Inspection...
Page 22
Maintenance and Inspection > Cleaning Periodically Replaced Parts Periodic replacement parts are not required in this printer. Consumable Parts Consumable parts are not required in this printer. Periodical Service No periodic services are required to this printer. Cleaning No cleanings are required to this printer. Maintenance and Inspection >...
Troubleshooting ■ Outline of Electrical Components Troubleshooting...
Page 24
Troubleshooting > Outline of Electrical Components Outline of Electrical Components F-5-1 Key No. Name Reference Paper Feeder Separation Roller (Refer to page 3-9) Paper Feeder Pickup Roller (Refer to page 3-9) Paper Feeder Paper Detection Sensor Paper Feeder Pickup Solenoid Paper Feeder Pickup Unit (Refer to page 3-10) Paper Feeder Relay PCB...
Appendix ■ Service Tools ■ General Circuit Diagram...
Page 26
Appendix > Service Tools Service Tools To perform servicing for this machine, no special tools are available other than the set of necessary standard tools. Appendix > Service Tools...
Page 27
General Circuit Diagram J4004LA J4004L PCB13 Paper Feeder Relay PCB to Host COR3 +24VA Machine SGND J1203 OPTPS J1202 OPTPKSL J4004L_BUS[0:7] J3007 Paper Feeder Paper Paper Feeder Detection Sensor Pickup Solenoid F-6-1...