Sony XAV-612BT Service Manual

Sony XAV-612BT Service Manual

Av center
Hide thumbs Also See for XAV-612BT:

Advertisement

Quick Links

SERVICE MANUAL
Ver. 1.0 2013.11
The service manual of the mechanism
deck, used in this model, has been issued
in a separate volume. Please refer to the
service manual of the MG-614 series for
the mechanism deck information.
Monitor section
Display type: Wide LCD color monitor
Dimensions:
6.1 in
System: TFT active matrix
Number of pixels:
1,152,000 pixels (800 × 3 (RGB) × 480)
Color system:
PAL/NTSC/SECAM/PAL-M/PAL-N automatic
select
Tuner section
(E (PAL), Indian and Australian models)
FM
Tuning range: 87.5 – 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
25 kHz
Usable sensitivity:
9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio (stereo):
80 dB (mono)
Separation at 1 kHz: 50 dB
Frequency response:
20 - 15,000 Hz
AM
Tuning range: 531 – 1,602 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
9,124.5 kHz or 9,115.5 kHz/4.5 kHz
Sensitivity: 26 μV
Tuner section (E (NTSC) model)
FM
Tuning range:
87.5 - 108.0 MHz (at 100 kHz step)
87.5 - 107.9 MHz (at 200 kHz step)
FM tuning step: 100 kHz/200 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
25 kHz
Usable sensitivity:
9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio (stereo):
80 dB (mono)
Separation at 1 kHz: 50 dB
Frequency response:
20 - 15,000 Hz
AM
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
9,124.5 kHz or 9,115.5 kHz/4.5 kHz
Sensitivity: 26 μV
9-893-902-01
Sony Corporation
2013K33-1
©
2013.11
Published by Sony Techno Create Corporation
SPECIFICATIONS
Tuner section (Russian model)
FM
Tuning range:
FM1/FM2: 87.5 - 108.0 MHz (at 50 kHz step)
FM3: 65 - 74 MHz (at 30 kHz step)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
25 kHz
Usable sensitivity:
9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio (stereo):
80 dB (mono)
Separation at 1 kHz: 50 dB
Frequency response:
20 - 15,000 Hz
MW/LW
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
9,124.5kHz or 9,115.5kHz/4.5kHz
Sensitivity: MW: 26 μV, LW: 46 μV
DVD/CD Player section
Signal-to-noise ratio:
120 dB
Frequency response:
10 – 20,000 Hz
Wow and flutter:
Below measurable limit
Harmonic distortion:
0.01%
Region code:
Labeled on the bottom of the unit
USB Player section
Interface: USB (High-speed)
Maximum current: 1 A
1.5 A (HIGH CHARGE mode)
HDMI in / MHL in section
Interface: HDMI in / MHL in
Incorporates MHL 2 (only MHL)
Maximum current (only MHL):
0.9 A
Wireless Communication
Communication System:
BLUETOOTH Standard version 2.1 + EDR
Output:
BLUETOOTH Standard Power Class 2 (Max. +4
dBm)
Maximum communication range:
Line of sight approx. 10 m (33 ft)*
2
Frequency band:
2.4 GHz band (2.4000 – 2.4835 GHz)
Modulation method:
FHSS
XAV-612BT
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
Compatible BLUETOOTH Profiles*
3
:
A2DP (Advanced Audio Distribution Profile) 1.2
AVRCP (Audio Video Remote Control Profile) 1.3
HFP (Handsfree Profile) 1.5
PBAP (Phone Book Access Profile)
OPP (Object Push Profile)
SPP (Serial Port Profile)
Maximum number of storable phonebook
contacts: 1,000
*2 The actual range will vary depending on factors such
as obstacles between devices, magnetic fields
around a microwave oven, static electricity,
reception sensitivity, antenna's performance,
operating system, software application, etc.
*3 BLUETOOTH standard profiles indicate the purpose
of BLUETOOTH communication between devices.
Power amplifier section
Outputs: Speaker outputs
Speaker impedance:
4 – 8 ohms
Maximum power output:
52 W × 4 (at 4 ohms)
General
Outputs:
Video output terminal (rear)
Audio output terminals (front/rear)
Audio output terminal (Z×Z)
Subwoofer output terminal
Power antenna (aerial)/Power amplifier control
terminal (REM OUT) (Except Russian model)
Power antenna (aerial) relay control terminal (Russian model)
Power amplifier control terminal (Russian model)
Inputs:
Illumination control terminal
Remote controller input terminal
Antenna (aerial) input terminal
Parking brake control terminal
Microphone input terminal
Reverse input terminal
Camera input terminal
AUX audio input terminals
AUX video input terminals
USB ports
HDMI in / MHL in port
E Model
Australian Model
Russian Model
XAV-602BT
MG-614D-189
TOP1300SE C11
Power requirements:
12 V DC car battery
(negative ground (earth))
Dimensions:
Approx. 178 mm × 100 mm × 173 mm
(7
1
/
× 4 × 6
7
/
in) (w/h/d)
8
8
Mounting dimensions:
Approx. 182 mm × 111 mm × 160 mm
(7
1
/
× 4
3
/
× 6
3
/
in) (w/h/d)
4
8
8
Mass:
Approx. 2.0 kg (4 lb 7 oz)
Package contents:
Parts for installation and connections (1 set)
Microphone (1)
Remote Commander (1): RM-X271
HDMI connection cable (1): RC-400VH
MHL connection cable (1): RC-500VM
Panel Case (1)
Design and specifications are subject to change
without notice.
Region code
The region system is used to protect software
copyrights.
The region code is located on the bottom of the
unit, and only DVDs labeled with an identical region
code can be played on this unit.
DVDs labeled
can also be played.
If you try to play any other DVD, the message [Disc
playback prohibited by region code.] will appear on
the monitor screen. Depending on the DVD, no
region code may be labeled even though playing
the DVD is prohibited by area restrictions.
AV CENTER

Advertisement

Table of Contents
loading

Summary of Contents for Sony XAV-612BT

  • Page 1 External antenna (aerial) connector Frequency band: Intermediate frequency: 2.4 GHz band (2.4000 – 2.4835 GHz) 9,124.5 kHz or 9,115.5 kHz/4.5 kHz Modulation method: FHSS Sensitivity: 26 μV AV CENTER 9-893-902-01 Sony Corporation 2013K33-1 © 2013.11 Published by Sony Techno Create Corporation...
  • Page 2 ANY OTHER USE. ADDITIONAL INFORMATION the Bluetooth SIG, Inc. and any use of such marks INCLUDING THAT RELATING TO PROMOTIONAL, by Sony Corporation is under license. Other INTERNAL AND COMMERCIAL USES AND LICENSING trademarks and trade names are those of their MAY BE OBTAINED FROM MPEG LA, LLC.
  • Page 3: Table Of Contents

    XAV-612BT TABLE OF CONTENTS SERVICING NOTES 5-3. Block Diagram - POWER SUPPLY Section - ....30 ..........5-4. Printed Wiring Boards - MAIN Section (1/2) - ....32 5-5. Printed Wiring Board - MAIN Section (2/2) - ....33 GENERAL ..............
  • Page 4: Servicing Notes

    This unit does not use security function by password lock. IMPORTANT NOTE FOR REPAIRING Part No. XAV-612BT contain individual information that the customer reg- istered because it installs the Bluetooth function. When repairing, the data that the customer registered might disap- pear.
  • Page 5 XAV-612BT NOTE THE MAIN BOARD OR SYSTEM CONTROLLER 1. Press the [ ] or [ ] button, and select the alphanumeric char- (IC502) REPLACING acter of “0 to F”. When the complete MAIN board or system controller (IC502) is 2. The digit advances by pressing the [ ] button.
  • Page 6 XAV-612BT NOTE FOR FLEXIBLE BOARD OF THE OPTICAL REPLACING THE LITHIUM BATTERY OF THE REMOTE COMMANDER PICK-UP Under normal conditions, the battery will last When connecting or disconnecting the fl exible board of the opti- approximately 1 year. (The service life may be cal pick-up to or from the CN2 of the SERVO board, follow the shorter, depending on the conditions of use.)
  • Page 7: General

    XAV-612BT SECTION 2 This section is extracted GENERAL from instruction manual. (E (NTSC) model) English Español Equipment used in illustrations (not supplied) / Equipo utilizado en las ilustraciones (no suministrado) Cautions Precauciones Run all ground (earth) leads to a common gr ound Conecte todos los cables de c onexión a masa a un...
  • Page 8 Location of screw holes automóviles japoneses sin el soporte suministr ado. En Ubicación de los orificios para los tornillos no ACC position caso de que no pudier a, consulte al distribuidor Sony T: TOYOTA más cercano. M: MITSUBISHI Be sur e to set the Auto OFF function. For details, refer...
  • Page 9 XAV-612BT (E (PAL), Indian and Australian models) English Equipment used in illustrations (not supplied) Cautions Run all ground (earth) leads to a common gr ound (earth) point. Front speaker Rear speak er Rear view c amera This unit is designed f or negative ground (earth) 12 V DC operation only.
  • Page 10 . If the fuse blows again after r eplacement, there may be an internal malfunction. In such a c ase , consult your near est Sony dealer . Fuse (10 A)
  • Page 11 XAV-612BT (Russian model) Русский Українська Оборудование, фигурирующее на иллюстрациях (не прилаг ается) / Обладнання, зображ ене на ілюстраціях (не вх одить до комплекту пос тачання) Внимание Увага! Подведите все провода заземления к одной Підключіть усі проводи заземлення до однієї точке заземления.
  • Page 12 XAV-612BT Русский Українська Меры предосторо жности Застережні заходи Ножной тормо з Ручной тормо з Педальне г альмо Ручне гальмо Место д ля установки устройства выбирайте Уважно виберіть місце встановлення, щоб тщательно, чтобы оно не мешало управлению пристрій не заважав керувати автомобілем.
  • Page 13: Disassembly

    XAV-612BT SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW FRONT PANEL SECTION Note: Illustration of disassembly is omitted. 3-2. FUSE (BLADE TYPE) (AUTO FUSE) (F801), COVER 3-13. PANEL (BACK) BLOCK (Page 14) (Page 22) 3-3.
  • Page 14: Fuse (Blade Type) (Auto Fuse) (F801), Cover

    XAV-612BT Note: Follow the disassembly procedure in the numerical order given. 3-2. FUSE (BLADE TYPE) (AUTO FUSE) (F801), COVER 3 two claws 5 cover 2 screw (PTT2.6 3 two claws 4 three claws 1 fuse (blade type) (auto fuse) (F801) –...
  • Page 15: Dvd Mechanism Deck (Mg-614D-189)

    XAV-612BT 3-3. DVD MECHANISM DECK (MG-614D-189) Note 1: The service manual of the mechanism deck, used in this model, has been issued in a separate volume. Please refer to the service manual of the MG-614 series for the mechanism deck informa- tion.
  • Page 16: Back 6 Shield, Bracket (Cover)

    XAV-612BT 3-4. BACK 6 SHIELD, BRACKET (COVER) Note: When installing the bracket (cover), after the cable for automobile (HDMI) is fixed with a screw, check that not being damaged with metal part of J702. metal part J702 cable for automobile...
  • Page 17: If Board

    XAV-612BT 3-5. IF BOARD 4 two screws (T) 7 cable for automobile (HDMI) (CNC101) (CN9703) 8 IF board 1 connector (CN9705) 5 Remove the IF board block in the direction of an arrow. 3 connector (CN9702) (E (PAL), Indian, Australian)
  • Page 18: Connector Assy (Nv1) (E (Pal), Indian And Australian Models)

    XAV-612BT 3-6. CONNECTOR ASSY (NV1) (E (PAL), Indian and Australian models) 3 connector assy (NV1) 1 connector (CN940) 2 two screws (PTT2.6 Note: When you install the connector, please install themcorrectly. There is a possibility that this machine damages when not correctly installing it.
  • Page 19: Bracket (Mhl)

    XAV-612BT 3-8. BRACKET (MHL) 1 two screws (T) i e e i 2 bracket (MHL) – Top view – cable for automobile (USB) bracket (MHL) MAIN board Note: Arrange the cable for automobile (USB) between these portions. 3-9. CONNECTION CORD FOR AUTOMOBILE (...
  • Page 20: Main Board Block

    XAV-612BT 3-10. MAIN BOARD BLOCK 2 two screws (PTT2.6 4 boss 3 ground point screw (PTT2.6 2 two screws 4 boss (PTT2.6 3 ground point screw (PTT2.6 6 MAIN board block 3 ground point screw 1 flexible printed wiring (PTT2.6...
  • Page 21: Dc Fan (25X25) (M801), Main Board

    XAV-612BT 3-11. DC FAN (25X25) (M801), MAIN BOARD 3 connector (CN701) 2 connector 1 connector (CN502) (CN802) 5 screw (PTT2.6 7 DC fan 8 MAIN board (M801) 4 connector (CN803) 5 screw (PTT2.6 6 tape (sub material) DC fan (25...
  • Page 22: Sub Panel Assy

    XAV-612BT 3-12. SUB PANEL ASSY Note: When you install the flexible printed wiring board, please install it correctly. There is a possibility that this machine damages when not correctly installing it. Insert is straight Insert is shallow Insert is incline to the interior.
  • Page 23: D-Sub6 Board

    XAV-612BT 3-14. D-SUB6 BOARD 1 two shafts 2 sheet (lock assy) 3 screw (B) 6 D-SUB6 board 3 screw (B) 3 screw (B) 4 Remove the solder. 5 plate (GND) – Back panel block front side view – 3-15. KEY6 BOARD...
  • Page 24: Chassis (Display6) Block

    XAV-612BT 3-16. CHASSIS (DISPLAY6) BLOCK 5 claw – Front panel block rear side view – 4 flexible flat cable (10 core) (CN4600) 2 touch panel flexible board (CN4500) 6 chassis (display6) block 5 two claws 5 claw 5 claw 3 flexible flat cable (60 core)
  • Page 25: Display Board

    XAV-612BT 3-17. DISPLAY BOARD Note 1: When complete DISPLAY board is exchanged, exchanged old complete DISPLAY board and is destroyed with the hammer, and throw out it. 2 Remove the solder. 6 DISPLAY board 3 Bend the claw in the...
  • Page 26: Liquid Crystal Display Panel (Lcd1), Touch Panel (Tpn1)

    XAV-612BT 3-18. LIQUID CRYSTAL DISPLAY PANEL (LCD1), TOUCH PANEL (TPN1) 5 liquid crystal display panel (LCD1) settin Note: When liquid crystal display panel (LCD1) is exchanged, refer to “ELECTRICAL ADJUSTMENT” on page 27. flexible flat cable sheet (LCD) guide line...
  • Page 27: Electrical Adjustment

    XAV-612BT SECTION 4 ELECTRICAL ADJUSTMENT the rear side of main unit. MONITOR SECTION 6. Press the [B] or [b] buttons on the remote commander, change If any of the following parts was replaced, execute the “Flicker to the PAL adjustment screen.
  • Page 28: Diagrams

    XAV-612BT SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - AUDIO Section - J702 (1/3) LINE IC351 INPUT SELECTOR, R-CH ELECTRICAL VOLUME AMUTE IC301 MUTING Q311 POWER AMP AUDIO_FL 33 INF1 IC801 (1/2) R-CH AUDIO_FR R-CH DVD MECHANISM CN801 (1/2) DECK BLOCK...
  • Page 29: Block Diagram - Video, Panel Section

    XAV-612BT 5-2. BLOCK DIAGRAM - VIDEO, PANEL Section - PSW_EN_OUT CDP/SDP USB CHARGING USB INTERFACE CONTROLLER R-ch is omitted due to same as L-ch. IC201 IC202 SIGNAL PATH USB_ON1 SYSRSTB : AUDIO PSW_EN_OUT 7 DISPLAY BOARD CHG_MOD1 1 X203 : USB...
  • Page 30: Block Diagram - Power Supply Section

    XAV-612BT 5-3. BLOCK DIAGRAM - POWER SUPPLY Section - M801 (FAN) +1.9V REGULATOR D +1.9V REGULATOR IC801 (2/2) IC101 SYS_ENA (Page 29) F_SYNC DR +5V 33 MECHA_5V AUDIO +8.7V 30 AUDIO_8.7V CN801 (2/2) MECHA +3.3V 31 MECHA_3.3V PSW_EN_OUT ANT-REM CDP/SDP...
  • Page 31 XAV-612BT THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: Note: SERVO board • All capacitors are in μF unless otherwise noted. (p: pF) 50 •...
  • Page 32: Printed Wiring Boards - Main Section (1/2)

    XAV-612BT 5-4. PRINTED WIRING BOARDS - MAIN Section (1/2) - • See page 31 for Circuit Boards Location. • : Uses unleaded solder. MAIN BOARD (COMPONENT SIDE) R343 R300 R316 R344 R317 VDR309 VDR311 VDR301 C388 C818 R872 C820 VDR315...
  • Page 33: Printed Wiring Board - Main Section (2/2)

    XAV-612BT 5-5. PRINTED WIRING BOARD - MAIN Section (2/2) - • See page 31 for Circuit Boards Location. • : Uses unleaded solder. J702 CNC1 AUX1 CAMERA AUX1 REAR FRONT AUX2 MAIN BOARD AUDIO IN AUDIO OUT AUDIO OUT AUDIO IN...
  • Page 34: Schematic Diagram - Main Section (1/4)

    XAV-612BT 5-6. SCHEMATIC DIAGRAM - MAIN Section (1/4) - • See page 45 for IC Block Diagrams. M801 MAIN BOARD (1/4) CN803 (FAN) IC B/D IC801 R836 C856 C867 D829 C953 Q852 0.47 0.47 DZ2J180M0L POWER AMP, REGULATOR LSCR523UBFS8TL IC801...
  • Page 35: Schematic Diagram - Main Section (2/4)

    XAV-612BT 5-7. SCHEMATIC DIAGRAM - MAIN Section (2/4) - • See page 43 for Waveforms. • See page 45 for IC Block Diagrams. MAIN BOARD (2/4) MAIN BOARD (3/4) (Page 36) C105 R123 C101 0.01 C416 C417 C345 C346 R338...
  • Page 36: Schematic Diagram - Main Section (3/4)

    XAV-612BT 5-8. SCHEMATIC DIAGRAM - MAIN Section (3/4) - • See page 43 for Waveforms. • See page 45 for IC Block Diagrams. • See page 51 for IC Pin Function Description. MAIN BOARD (3/4) BUS4 REG+3.3V MAIN M_CVBS_GND BOARD...
  • Page 37: Schematic Diagram - Main Section (4/4)

    XAV-612BT • See page 43 for Waveforms. • See page 45 for IC Block Diagrams. • See page 51 for IC Pin Function Description. 5-9. SCHEMATIC DIAGRAM - MAIN Section (4/4) - MAIN BOARD (4/4) IC703 IC B/D VIDEO SELECT...
  • Page 38: Printed Wiring Board - M-Sub6 Board

    XAV-612BT 5-10. PRINTED WIRING BOARD - M-SUB6 Board - • See page 31 for Circuit Boards Location. • : Uses unleaded solder. D-SUB6 (Page 40) BOARD M-SUB6 BOARD (SIDE A) M-SUB6 BOARD (SIDE B) CN2001 CN2301 CN2300 (CHASSIS) C2305 C2304...
  • Page 39: Schematic Diagram - M-Sub6 Board

    XAV-612BT 5-11. SCHEMATIC DIAGRAM - M-SUB6 Board - M-SUB6 BOARD CN2300 VBUS_GND VBUS C2305 VBUS 100p VBUS VBUS_GND USB_D– USB_D– USB_D+ USB_D+ VBUS_GND (Page 41) +7.5V D-SUB6 BOARD +7.5V CN2001 +7.5V CN2301 +7.5V DETACH_DET USB_D– +7.5V 46 DETACH-DET USB_D– BU_IN...
  • Page 40: Printed Wiring Board - D-Sub6 Board

    XAV-612BT 5-12. PRINTED WIRING BOARD - D-SUB6 Board - • See page 31 for Circuit Boards Location. • : Uses unleaded solder. DISPLAY (Page 42) M-SUB6 BOARD (Page 38) BOARD CN2301 D-SUB6 BOARD D-SUB6 BOARD (SIDE A) (SIDE B) CN2001...
  • Page 41: Schematic Diagram - D-Sub6 Board

    XAV-612BT 5-13. SCHEMATIC DIAGRAM - D-SUB6 Board - (Page 44) D-SUB6 BOARD DISPLAY BOARD (Page 39) CN2000 M-SUB6 BOARD VBUS_GND VBUS USB_D– CN2301 USB_D– VBUS C2002 CN2001 USB_D+ 100p R2000 D2020 VDR992 USB_D+ VBUS DETACH_DET USB_D– VBUS_GND VBUS_GND 46 DETACH_DET USB_D–...
  • Page 42: Printed Wiring Boards - External Terminal, Panel Section

    XAV-612BT 5-14. PRINTED WIRING BOARDS - EXTERNAL TERMINAL, PANEL Section - • See page 31 for Circuit Boards Location. • : Uses unleaded solder. KEY6 BOARD KEY6 BOARD (COMPONENT SIDE) (CONDUCTOR SIDE) (E (PAL), IND, AUS) EXT-NAVI BOARD (Page 40)
  • Page 43: Schematic Diagram - Ext-Navi Board (E (Pal), Indian And Australian Models)

    XAV-612BT 5-15. SCHEMATIC DIAGRAM - EXT-NAVI Board (E (PAL), Indian and Australian models) - • Waveforms – MAIN Board – IC401 1 (BST) EXT-NAVI BOARD C603 R627 R647 18.2 Vp-p R607 R619 JL604 2.46 s 5 V/DIV, 1 s/DIV R622...
  • Page 44: Schematic Diagram - Panel Section

    XAV-612BT 5-16. SCHEMATIC DIAGRAM - PANEL Section - KEY6 BOARD C2500 S2503 IC2500 ROTARY ENCODER PUSH SOURCE/ REMOTE CONTROL RECEIVER IC2500 RS-470 (VOLUME) R2507 GND1 CN2501 GND2 KEY_GND R2548 SIRCS R2500 DISP_10.4V R2512 R2515 R2518 3.3V S2500 R2505 LED_GND FFC3...
  • Page 45 XAV-612BT • IC Block Diagrams – MAIN Board – IC101 BD00GA5WEFJ-E2 IC102 BD7931F IC103 BD00GA3WEFJ-E2 IC105 BD00GC0WEFJ-SE2 CONTROL LOGIC POWER CMOS THERMAL H-BRIDGE SHUT-DOWN SOFT IC104 NJM2387ADL3 (TE2) REGULATOR OVER VOLTAGE OVER CURRENT PROTECTION PROTECTION BANDGAP REFERENCE THERMAL ON/OFF PROTECTION...
  • Page 46 XAV-612BT IC301 BD3467FV-E2 FADER FADER BOOST OUTC FADER FADER A1 1 BOOST OUTS A2 2 FADER FADER B1 3 OUTR1 BOOST B2 4 FADER FADER OUTR2 BOOST CP1 5 FADER FADER CN 6 OUTF1 BOOST CP2 7 FADER FADER OUTF2...
  • Page 47 XAV-612BT IC302 NJW1240V (TE2) MUTING OUT1 IN1 1 MUTING OUT2 IN2 2 MUTING OUT3 IN3 3 MUTING OUT4 IN4 4 MUTING OUT5 IN5 5 MUTING OUT6 IN6 6 POP NOISE MUTE 7 SUPPRESSION GAIN SELECT GAIN 8 6 dB/8 dB...
  • Page 48 XAV-612BT IC401, 431 OZ529IEGN-A1-0-TR BST 1 VREF OSCILLATOR LX 2 REFERENCE GENERATOR OVER CURRENT PROTECTION GNDA VIN 3 EN_SYS 4 USBOUT 5 FB_USB 6 SS_SYS ADJUSTMENT GENERATOR CHARGE EN_USB PUMP VIC_USB USBIN OVER-CURRENT ISET_USB LIMIT VOUT_SYS (USBIN) UVLS FAULT PROTECTION –...
  • Page 49 XAV-612BT IC461 SI-8205NHG-TL REG_DRV ISNS GND 1 ICSPWM SS_REF ENABLE/ CURRENT EN/SS 2 ICSOCP POWER SOFT-START SENSE STANDBY STAGE VIN 3 OVER CURRENT REGULATOR PROTECT COMPARATOR REGULATOR VINOK UNDER PHASE VOLTAGE CURRENT RES_PH PHASE GATE CBCHG BS_CHG LOCK OUT LSOFF...
  • Page 50 XAV-612BT IC703 NJM41050V (TE2) CLAMP VIN1 SREFV ADVANCED 12 VSAG CORRECTION CLAMP 11 SREFV VIN2 10 VCC 9 GND DRIVER 6.75MHz CLAMP LOW-PASS 8 VOUT FILTER – VIN3 MUTE IC801 TDF8556AJ/N5 – EXT-NAVI Board – IC601 BA3123F-E2 OUT1 I2C_SIO OUT2 OUT-FL–...
  • Page 51 XAV-612BT • IC Pin Function Description MAIN BOARD IC201 PD720114GA-YEU-A-SAK (USB INTERFACE) Pin No. Pin Name Description VDD25OUT Internal regulator power supply voltage (+2.5V) output terminal VSSREG Ground terminal (for internal regulator) 3 to 6 LED4 to LED1 Not used...
  • Page 52 XAV-612BT MAIN BOARD IC502 R5F3650KCDZ92FB (SYSTEM CONTROLLER) Pin No. Pin Name Description SPEED_IN Speed pulse signal input terminal Not used SIRCS SIRCS signal input from the panel section MHL_OVER Over current detection signal input from the MHL section “L”: over current...
  • Page 53 XAV-612BT Pin No. Pin Name Description IN_SW Disc insert detection switch input terminal D_SW Chucking end detection switch input terminal MECHA_RESET Reset signal output to the DVD mechanism deck block “L”: reset MECHA_CTS Clear to send signal output to the DVD mechanism deck block...
  • Page 54: Exploded Views

    XAV-612BT SECTION 6 EXPLODED VIEWS Note: The components identifi ed by mark 9 con- • -XX and -X mean standardized parts, so • Color Indication of Appearance Parts Ex- tain confi dential information. they may have some difference from the...
  • Page 55: Front Panel Section

    XAV-612BT 6-2. FRONT PANEL SECTION LCD1 TPN1 not supplied FFC3 not supplied not supplied Note 1: When complete DISPLAY board or front panel cpmplete assy (FP1) is exchanged, exchanged old complete DISPLAY board and is destroyed with the hammer, and throw out it.
  • Page 56: Sub Panel Section

    XAV-612BT 6-3. SUB PANEL SECTION FPB1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-439-172-01 CUSHION (LOCK ASSY) A-1871-747-A M-SUB6 BOARD, COMPLETE 3-042-244-11 SCREW (T) 4-298-967-02 PLATE (ADJUST) 3-243-844-02 CUSHION (SUB PANEL) FPB1 1-886-726-11 PRINTED WIRING BOARD, FLEXIBLE...
  • Page 57: If Board Section

    XAV-612BT 6-4. IF BOARD SECTION CNC101 (E (PAL), IND, AUS) CWC1 EXT-NAVI board CWC3 CWC2 not supplied supplied (E (PAL), IND, AUS) chassis section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CWC2 1-846-905-11 CABLE WITH CONNECTOR...
  • Page 58: Chassis Section

    XAV-612BT 6-5. CHASSIS SECTION CNC202 MAIN board section not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-417-843-01 SHEET (GND), BRACKET CNC202 1-846-886-11 CABLE FOR AUTOMOBILE (USB) ( ) 2-894-799-01 SCREW +PTW S2X5...
  • Page 59: Main Board Section

    XAV-612BT 6-6. MAIN BOARD SECTION F801 not supplied not supplied M801 CN01 MAIN board not supplied not supplied Note: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC502) REPLACING” on page 5.
  • Page 60: Electrical Parts List

    XAV-612BT SECTION 7 DISPLAY D-SUB6 EXT-NAVI ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- uF: μF the parts list may be different from the ber, please include the board name.
  • Page 61 XAV-612BT EXT-NAVI KEY6 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R609 1-216-864-11 SHORT CHIP R2501 1-218-953-11 METAL CHIP 1/16W R610 1-216-864-11 SHORT CHIP R2502 1-218-953-11 METAL CHIP 1/16W R611 1-216-864-11 SHORT CHIP R2503 1-216-822-11 METAL CHIP 1.2K...
  • Page 62 XAV-612BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C118 1-118-345-11 CERAMIC CHIP 0.01uF C341 1-162-923-11 CERAMIC CHIP 47PF C119 1-118-347-11 CERAMIC CHIP 0.1uF C120 1-118-462-11 CERAMIC CHIP 1uF C342 1-162-921-11 CERAMIC CHIP 33PF C121...
  • Page 63 XAV-612BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C410 1-115-412-11 CERAMIC CHIP 680PF C720 1-118-459-11 CERAMIC CHIP 0.01uF C411 1-117-681-11 ELECT CHIP 100uF C723 1-116-718-11 CERAMIC CHIP 10uF C412 1-116-715-11 CERAMIC CHIP 10uF C725...
  • Page 64 XAV-612BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C866 1-118-345-11 CERAMIC CHIP 0.01uF D825 6-502-961-01 DIODE DA2J10100L C867 1-116-739-11 CERAMIC CHIP 0.47uF D826 6-502-961-01 DIODE DA2J10100L D827 6-503-032-01 DIODE DZ2J180M0L C869 1-162-919-11 CERAMIC CHIP 22PF...
  • Page 65 XAV-612BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL/JUMPER RESISTOR > R151 1-218-875-11 METAL CHIP 0.5% 1/10W R152 1-218-887-11 METAL CHIP 0.5% 1/10W 1-400-073-21 INDUCTOR 4.7uH R209 1-216-864-11 SHORT CHIP L101 1-481-182-21 INDUCTOR...
  • Page 66 XAV-612BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R350 1-216-809-11 METAL CHIP 1/10W R467 1-218-953-11 METAL CHIP 1/16W R351 1-216-845-11 METAL CHIP 100K 1/10W R468 1-218-953-11 METAL CHIP 1/16W R352 1-216-809-11 METAL CHIP 1/10W...
  • Page 67 XAV-612BT MAIN M-SUB6 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R578 1-216-864-11 SHORT CHIP R917 1-216-864-11 SHORT CHIP R580 1-216-841-11 METAL CHIP 1/10W R947 1-216-864-11 SHORT CHIP 0 (E (PAL), IND, AUS) R583 1-216-845-11 METAL CHIP...
  • Page 68 XAV-612BT Ref. No. Part No. Description Remark MISCELLANEOUS ************** CNC1 1-839-912-11 CORD, CONNECTION (20P) (REVERSE IN/ SUB OUT/FRONT AUDIO OUT/REAR AUDIO OUT/ AUX1 AUDIO IN/AUX2 AUDIO IN) CNC101 1-846-926-11 CABLE FOR AUTOMOBILE (HDMI) CNC202 1-846-886-11 CABLE FOR AUTOMOBILE (USB) ( )
  • Page 69 XAV-612BT MEMO...
  • Page 70 XAV-612BT REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2013.11...

Table of Contents