Care; Troubleshooting; Specifications; Completing Units - Electrolux ECH/T-1000 E EEC User Manual

10 http://www.home-comfort.com

Care

The convector does not require any special
maintenance. Before servicing (leaving) the
convector must be disconnected from the
power supply.
The body of the device should be periodically
wiped with a soft, lint-free cloth or damp
sponge. Never use abrasive, foaming
detergents or solvents. It is quite easy to clean
the space behind a wall-mounted heater.
Press down the two latches on the back of the

Troubleshooting

Malfunction
Cause of malfunction
symptom
1) There is no power supply.
2) The convector is in standby mode.
No heating 3) The actual room temperature is higher
than the thermostat setting.
Smell of burnt dust
Not a malfunction
when first turned on
If after trying all the troubleshooting steps, the problem is not resolved, contact an authorized service cen-
ter in your area or your sales representative.

Specifications

Model
Rated power consumption, W
Rated current, A
Rated voltage, V~Hz
Ingress protection class
Electrical protection class
Heating area, m *
2
Appliance size (W×H×D), mm
Packing size (W×H×D), mm
Net weight, kg
Gross weight, kg
* Indicated is a guideline value and may differ depending on actual conditions of use
heater and pull the heater forward. After it is
removed, you can wash the wall on which it
was installed.
After finishing cleaning, put the heater back in
its normal operating position.
Recommended indoor temperature and
humidity:
a) for the convector operation: from -25°С to
+ 30°С, humidity from 40% to 90%;
b) for the storage of the convector: from -20°C
to + 80°С, humidity from 40% to 90%.
Troubleshooting steps
1) Establish a reliable connection.
2) Set the convector to operating
mode.
3) Adjust the temperature mode of the
convector.
The smell disappears after a few
minutes of convector operation
ECH/T – 1000 ECH/T – 1500 ECH/T – 2000
E EEC E EEC
900-1000 1350-1500
4.1-4.17 6.14-6.25
220-240~50-60 220-240~50-60 220-240~50-60
IP24 IP24
I I
10-12 13-15
480×413×113 640×413×113 800×413×113
575×445×142 735×445×142 895×445×142
3.44 4.33
4.57 5.67
The convector is supplied with a sticker on
the front panel. Remove it before using the
device.
Troubleshooting
E1 - temperature sensor malfunction
E2 - overheating in the room is more than
50ºC If these errors occur, contact your
dealer.

Completing units

1. Electric heater
2. Wall mounting bracket
3. Mounting template
4. A set of fasteners
5. Operation manual
6. Chassis set with wheels

Storing the appliance

Make sure the heater is cool before storing
it. It is recommended to clean the heater and
store (preferably in the original packaging) in
a cool dry place in case you plan not to use
device for a long time.

Recycling

E EEC
The time-expired appliance can't be
disposed with household waste (2012/19/EU).
1800-2000
8.18-8.33

Warranty

IP24
Warranty service is performed according
to the terms specified in the "Warranty"
I
section.
18-20
Warranty:
•
Warranty period for the item is two years
from the purchase date. If any defects
occur due to defects in materials and/or
5.33
workmanship during this two-year warranty
6.77 period, the item should be repaired
or replaced.
•
Free maintenance or replacement
is possible only in case if convincing
evidence is provided, for example a stub,
which confirms that the day when
ENGLISH
the service is requested, is within the
warranty period.
•
The warranty does not cover products
and/or parts of the product that
are subjects to deterioration, may
be considered as expendable supplies
or which are made of glass.
•
The warranty is void if the defect
is caused by damage ensuing by misuse,
poor maintenance (for example, a failure
occurred due to ingress of foreign objects
or liquids) or if changes or repairs were
performed by persons not authorized
by the Manufacturer.
•
For the correct use of the product,
the user must strictly follow all included
in the manual instructions, and also
must avoid any action or manipulation
described as unwanted or indicated so
in this manual.
•
These warranty restrictions do not affect
your statutory rights.
Support:
The support during and after the warranty
period is available in all countries where
the product is officially distributed. Please
contact your dealer for help.
Date of manufacture
The date of manufacture is indicated on
a sticker on the body of the appliance,
and also encrypted in Code-128. The date
of manufacture is determined as follows:
month and year of production
Do not remove and keep safe the serial
number on the device's body. If the serial
number sticker is lost or damaged, it will
not be possible to restore the production date
if necessary.
Importer:
Manufacturer: CladSwiss AG,
Bahnhofstrasse 27, 6300 Zug, Switzerland.
E-mail: info@cladswiss.com
11