Setting The Off Timer; Switching Off The Appliance; Function; Installation Of The Device - Electrolux ECH/T-1000 E EEC User Manual

8 http://www.home-comfort.com
display "d1", it will show Monday program
setting. Press "Time" could choose any day
of a week to show the program setting;
2. Press "Prog", it shows "1.", press "Prog", it
shows the 1st interval comfortable starting
hour;
3. Press "Prog" again, it shows the 1st interval
comfortable finish hour;
4. Press "Prog", it shows "2.", press "Prog", it
shows the 2nd interval comfortable starting
hour;
5. Press "Prog", it shows the 2nd interval
comfortable finish hour;
6. Press "Prog", it shows "3.", press "Prog", it
shows the 3rd interval comfortable starting
hour;
7. Press "Prog", it shows the 3rd interval
comfortable finish hour;
8. Repeat the above steps to check d1-d7, if
user wants to set one day, just press the
Time key and select the date which the
user needs, then press "Prog" to check.

Setting the off timer

Press the PROG button to set the timer. The
time will appear on the display and the timer
indicator on the display will flash. Press
buttons or to set the timer. The timer
range is from 0 to 24 hours. If the buttons
or are held down continuously, the time will
continuously increase or decrease by 1 hour
every 0.5 second. The factory timer setting
should be "0 hours". When the timer indicator
is on continuously, the system starts the timer
according to the last set value if no button
presses are made for 5 seconds after the timer
was set.
Each time you press the buttons or
set the timer, the system will reset to the new
preset time. When the set time has elapsed,
the system will automatically turn off the
heater, putting it into standby mode with
heating off.

Switching off the appliance

To turn off the device, press the button
any operating mode.
The difference between the on / off
temperatures for the set value can be
between 0.1 °C and 3 °C, depending on
the volume and thermal insulation of the
room / premises. We recommend that
when operating the device in large rooms
/ premises subject to rapid cooling, set the
temperature 2 - 3 °C higher than the desired
one for more efficient operation of the
heater.
Overheating protection function
The device is equipped with an automatic
switch that is activated when the upper
temperature limit is reached. The heater
switches off automatically in case of
overheating. After eliminating the source
of overheating, the heater will turn on
automatically.
"Open window" function
When this function is active, when the
temperature drops within 10 minutes (and then
up to 30 minutes) by 5 or more degrees - the
Anti-frost mode is switched on the heater.
If in the time interval 10 - 30 minutes the
temperature continues to drop, the device
turns off. Further, the heater waits for the
stabilization of the decrease in the room
temperature, if it rises by 2 degrees, then the
last set mode is turned on.
"Parental control" function
Locks all buttons on the control panel. While
the instrument is operating, press and hold the
left and right arrow buttons simultaneously for
a few seconds. The lock indicator lights up on
the display. The Parental Control function is
activated. To disable the function, repeat the
to
same operation as to enable.
"Auto Restart Resume" function
In the event of a short-term power outage,
and its further inclusion, the convector
automatically switches to the operating mode,
while maintaining the last operating mode of
in the device and the set temperature (if a timer
was set, the set shutdown time is saved). If the
device was in standby mode when the power
was turned off, it will remain in the same mode
when the power supply is restored.
"Anti-frost" function
Press the PROG button 2 times. The icon
– will appear on the display - anti - freezing
mode is on.

Installation of the device

Recommended installation
The device must be fixed in accordance with
the regulations.
The switch and other mechanisms must
stay away from splashing water. It is strictly
forbidden to cover or plug the air inlets or
outlets (grilles), due to the risk of accident or
damage to the device. Do not place behind
curtains, doors, wall or air vents. Observe
the minimum installation distances on floors,
surfaces, furniture, etc (Figure. 3).
100 mm
min.
100 mm 100 mm
min. min.
100 mm
min.
Figure. 3
Wall mounting of the device
• Release the wall bracket from the
convector: press the latches and pull the
bracket towards you by pressing down on
the two latches (fig. 4).
Bolts
dowel
wall
installation instruction
sheet
Figure. 4
ENGLISH
• Use the bracket as a marker of the
installation dimensions by attaching it to
the wall.
• Check the position of the bracket, then
mark and drill the holes.
• Place the bracket on the wall and fix it.
• fix the device to the bracket as follows (fig.
5).
• Place the lower part of the convector onto
the bracket using the special holes located
in the lower part of the convector (fig. 5a).
• Slide the upper part of the convector onto
the bracket, fixing it with the latches on the
bracket (fig. 5b).
• Tighten the screws into the latches on the
bracket.
b
a
Figure. 5
Floor installation
Using the chassis (supplied separately), having
previously studied the mounting scheme (Fig.
6), install the device on the floor:
1. Carefully turn the convector upside down
(Fig. 6).
2. Take one of the chassis and attach to the
landing area on the right or left side of the
convector so that it fits snugly against the
convector body
3. Secure the chassis using the supplied
mount (Fig. 7).
4. Repeat the same procedure for attaching
the second chassis.
Figure. 6 Figure. 7
9