Table of Contents
Advertisement
Quick Links
ROPS Kit
TimeCutter
Model No. 79485—Serial No. 400000000 and Up
Store this document with the Operator's Manual for the traction unit.
Safety
Rollover Protection System
(ROPS) Safety
•
The ROPS is an integral safety device. Do not
remove any of the ROPS components from the
machine.
•
Ensure that the seat belt is attached and that you
can release it quickly in an emergency.
•
Always wear your seat belt when the roll bar is
installed.
•
Check carefully for overhead objects before you
drive under them, and do not contact them.
•
Keep the roll bar in safe operating condition by
thoroughly inspecting it periodically for damage
and keeping all the mounting fasteners tight.
•
Replace damaged ROPS components. Do not
repair or alter them.
•
Wheels dropping over edges, over steep banks, or
into water can cause a rollover, which may result
in serious injury or death.
•
Do not wear the seat belt when the roll bar is not
installed.
•
In the event of a rollover, take the machine to an
Authorized Service Dealer to inspect the ROPS.
•
Use only Toro approved accessories and
attachments for the ROPS.
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Riding Mower
Safety and Instructional
Decals
Register at www.Toro.com.
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
145-6387
1. Warning—Read the Operator's Manual and wear a seat
belt.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3453-656 Rev A
Installation Instructions
decal145-6387
*3453-656*
Advertisement
Table of Contents
Related Manuals for Toro 79485
Summary of Contents for Toro 79485
- Page 1 Form No. 3453-656 Rev A ROPS Kit TimeCutter ® Riding Mower Model No. 79485—Serial No. 400000000 and Up Installation Instructions Store this document with the Operator’s Manual for the traction unit. Safety Safety and Instructional Decals Rollover Protection System Safety decals and instructions are...
-
Page 2: Table Of Contents
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Left ROPS mount Right ROPS mount Bolt (1/2 x 1-1/4 inches) Large washer Locknut (1/2 inch) Install the ROPS mounts and guard panels. -
Page 3: Procedure Description
Procedure Description Qty. ROPS tube Bolt (3/8 x 2-1/2 inches) Locknut (3/8 inch) Complete the installation. Suitcase weight (For machines with a bagger installed only) Bolt (3/8 x 3-3/4 inches) -
Page 4: No Parts Required
Remove the rear tires as shown in Figure 2 Note: Retain all wheel components for later installation. Preparing the Machine No Parts Required Procedure Note: Determine the left and right sides of the machine from the normal operating position. Note: You may discard all removed parts unless otherwise noted. - Page 5 Remove the pod brackets from the machine (Figure Note: Retain the shoulder screws removed from the sides of the pods for later installation. g310040 Figure 3 1. Hydraulic mount plate 3. Pod support bracket 4. Pod 2. Screw Note: Retain the fuel tank spring that secures the fuel tank to the left pod bracket for later installation.
-
Page 6: Left Rops Mount
Installing the ROPS Mounts and Guard Panels Parts needed for this procedure: Left ROPS mount Right ROPS mount Bolt (1/2 x 1-1/4 inches) Large washer Locknut (1/2 inch) Belt guard panel Rear guard panel g316031 Figure 5 Cable tie Right side shown Narrow push rivet Wide push rivet 1. -
Page 7: Left Seat Belt Bracket
Procedure Install the seat belt brackets to the seat platform with 2 partial-thread bolts (3/8 x 2 inches), 2 small washers, and 2 locknuts (3/8 inch) as Installing the Pod Brackets shown in Figure and Seat Belt MyRide-Equipped Machines Only Parts needed for this procedure: Left seat belt bracket (MyRide machines only) Right seat belt bracket (MyRide machines only) - Page 8 Install the left pod bracket to the machine frame using 2 thread-forming screws (5/16 x 3/4 inch) and the parts removed in 1 Preparing the Machine (page 4) as shown in Figure g310256 Figure 10 1. Thread-forming screw 3. Shoulder bolt (5/16 x 3/4 inch) g310244 2.
-
Page 9: Bumper
Installing the Pod Brackets and Seat Belt Machines without MyRide Only Parts needed for this procedure: Seat belt tongue assembly Seat belt buckle assembly Carriage screw (7/16 x 1 inch) Locknut (7/16 inch) Seat belt bracket (machines without MyRide only) g316063 Bolt (3/8 x 1 inch) Figure 11... - Page 10 Procedure Install the seat belt brackets to the outside of the ROPS mounts (Figure 13). Install the seat belt buckle and tongue to the Note: inside of the seat belt brackets with 2 carriage Install the seat belt buckle assembly with screws (7/16 x 1 inch) and 2 locknuts (7/16 inch) the bent bracket toward the seat.
-
Page 11: Thread-Forming Screw (5/16 X 3/4 Inch)
Install the left pod bracket to the machine frame using 2 thread-forming screws (5/16 x 3/4 inch) as shown in Figure g310244 Figure 14 1. Left pod bracket 3. Fuel-tank spring 2. Thread-forming screw 4. Shoulder bolt (5/16 x 3/4 inch) - Page 12 Completing the Installation Parts needed for this procedure: ROPS tube Bolt (3/8 x 2-1/2 inches) Locknut (3/8 inch) Suitcase weight (For machines with a bagger installed only) Bolt (3/8 x 3-3/4 inches) Procedure Install the rear tires as shown in Figure Lower the machine;...
- Page 13 Maintenance Checking the Seat Belt Service Interval: Before each use or daily Inspect the seat belt for wear, cuts, and proper operation of the retractor and buckle. Replace the seat belt if it is damaged. Checking the Rollover Protection System (ROPS) Service Interval: Before each use or daily Visually inspect the ROPS for loose hardware or any other possible problem.
- Page 14 Notes:...
- Page 15 Notes:...