Page 37
English For the customers in Europe WARNING This product with the CE marking complies with both the To prevent fire or shock hazard, do not expose the unit to EMC Directive (89/336/EEC) and the Low Voltage Directive rain or moisture. (73/23/EEC) issued by the Commission of the European Community.
Page 38
WARNING (For BKDS-7015/7025/7026 only) This unit has no power switch. When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power cord to a socket-outlet which must be provided near the unit and easily accessible. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power cord.
Page 39
Overview ....................4(E) Features ................... 4(E) Optional Accessories ...............5(E) Peripheral Equipment Configuration..........8(E) Location and Function of Parts ............10(E) DVS-7200A Digital Video Switcher ..........10(E) BKDS-7015 Switcher Control Panel ..........14(E) BKDS-7025/7026 Switcher Control Panel........16(E) System Configuration ................ 17(E) Control Panel Connections ............17(E) Primary Input and Video Monitor Connections ......
Overview Overview Completely digital processing for high picture The DVS-7200A Digital Video Switcher is a high- quality and excellent stability performance, multi-functional, composite (D2)/ Inheriting the digital video processing technology component (D1) format digital switcher for use in the established by the DVS-7200 Digital Video Switcher, construction of digital video systems.
Complete remote control functionality BKDS-7133 Chromakey Analog Component Input Board Full remote control of M/E banks is possible by connecting the BKDS-2010 as a subpanel to the Provides input capability for foreground chroma key signals, for use in composite or component systems. switcher.
Page 42
Overview BKDS-7280 M/E Preview Board BKDS-2031 Chromakey Board Enables key preview (K-PVW) outputs from the AUX Provides chroma key processing, for use in composite BUS OUTPUTS, PVW OUTPUT and CLEAN or component systems. One board can be installed for OUTPUT connectors which can be used for M/E each M/E, up to a total of two.
Page 43
BKDS-7031 DME Control Panel Unit Control panel accessories A control panel for installation in the BKDS-7015/ 7025/7026, for control of the DME-7000/3000 Digital BKDS-7015 Switcher Control Panel Multi Effects. It also enables control of the switcher A 2-M/E type switcher control panel. wipe positioner function.
B switch is turned on. circuit. Turn the switch off and contact qualified Sony As shipped, the A switch turns on or off the built-in service personnel.
Page 47
B connectors can be used. 5 ME-1/ME-2 OUTPUTS connectors (BNC type) For more information on the BKDS-7690, contact your Sony The images operated on by the control panel’s M/E representative or qualified Sony service personnel.
Page 48
Location and Function of Parts 7 PGM (program) OUTPUTS 1 to 4 connectors 0 CLEAN OUTPUT connector (BNC type) (BNC type) The final signal is output from this connector prior to These connectors output the final program signal in key processing. Also, by changing settings, it is either serial digital or analog composite format.
Page 49
1 CRK (chroma key) INPUTS 1 to 4 connectors 7 REF (reference) OUTPUT connector (BNC type) (BNC type) By installing optional BKDS-7133 boards (two Used to output an analog reference video signal. channels per board), up to four channels of analog Using control panel settings, the phase of the output µs to component video signals (Y/R–Y/B–Y/sync or RGB/...
Location and Function of Parts BKDS-7015 Switcher Control Panel Upper panel TERMINAL connector TERMINAL connector (D-sub 9-pin, RS-232C) Used to connect a pen tablet. Remove the lid and plug the cable from the pen tablet into the connector. This connector has the same function as the TERMINAL 1 connector on the rear panel.
Page 51
1 SWITCHER connector (D-sub 9-pin, RS-422A) Used to connect to the DVS-7200A Digital Video Switcher. The switcher is controlled through this connector. 2 DME (Digital Multi Effects) connector (D-sub 9-pin, RS-422A) Used to connect a device such as the DME-7000 Digital Multi Effects.
2 SWITCHER connector (D-sub 9-pin, RS-422A) For information on the BKDS-7090, contact your Sony representative or qualified Sony service personnel. Used to connect to the DVS-7200A Digital Video Switcher. The switcher is controlled through this 6 OPTION PANEL connector connector.
For information about the AC power cord of the BKDS-7015, c) For information about the switcher’s AC power cord, see see “Accessories not supplied” in “BKDS-7015” on page 26(E) “Accessories not supplied” in “DVS-7200A” on page 26(E) in the in the section “Specifications”. section “Specifications”.
Analog component inputs (up to 4 channels) Video camera Betacam VTR CRK INPUTS PRIMARY INPUTS D1 VTR Serial digital component signals DVW-series DVS-7200A Digital Video Switcher a) Primary inputs of composite signals cannot be used as chroma key source. 19(E)
:9-pin remote cable AUX BUS OUTPUTS (RS-422A) :75Ω coaxial cable DVS-7200A Digital Video Switcher K:Key signal a) Component mode: Connect connectors VIDEO/Y, KEY/Z, and Z with three cables. V:Video signal Composite mode: Connect connectors VIDEO/Y, EXT/C, KEY/Z, and Z with four cables.
(RS-422A) AUX BUS OUTPUTS :75Ω coaxial cable K:Key signal DVS-7200A Digital Video Switcher V:Video signal a) Component mode: Connect connectors VIDEO/Y, KEY/Z, and Z with three cables. Composite mode: Connect connectors VIDEO/Y, EXT/C, KEY/Z, and Z with four cables. 21(E)
System Configuration BVE-9100 Editing Control System Connections BVE-9100 Editing Control VTR1 System Program monitor VTR2 VTR for recording DME-7000 Digital Multi Effects Edit preview monitor AUX/PGM/PVW/EDIT PVW/ CLEAN/DIRECT OUTPUTS PRIMARY INPUTS EDITOR B EDITOR A DVS-7200A Digital Video Switcher 22(E)
DME 4 BKDS-7060 Keyer Remote Control Panel PANEL 2 BKDS-8060 Remote Panel DVS-7200A Digital Interface Unit Video Switcher BKDS-8062 Aux Bus Remote Panel a) Connectable to DME1 to DME3, EDITOR A, EDITOR B, or PANEL 2. b) Connectable to DME1 to DME3, EDITOR A, or EDITOR B.
Design and specifications are subject to change 75 Ω without notice. Signal type: Y/B–Y/R–Y (Betacam, SMPTE)/sync or G/B/R/sync DVS-7200A Digital Video Switcher Signal level: 0 ±3 dB REF INPUT General Analog black burst signal or analog sync signal input, BNC (× 2), 75 Ω, with loop-through Power requirements Signal level: 0±3 dB...
Page 61
PVW OUTPUT AC INPUT • When using BKDS-7163 AC INPUT [A] AC power input, 3-pin AC Serial digital video signal output, BNC ( × 1), 75 Ω connector ( × 1) Signal level: 800 mV ±10% AC INPUT [B] AC power input, 3-pin AC connector ( ×...
Page 62
Specifications 1,030 × 200 × 496 mm (40 × Dimensions Accessories not supplied × 19 inches) (w/h/d, excluding projections) AC power cord Mass 30 kg (66 lb 2 oz) • For customers in the USA and Canada DK-2401 (UC): Power cord (125V, 10A, 2.4m (8 feet)) Input/output connectors Plug retainer...
Page 63
Accessories supplied BKDS-7025/7026 Switcher Control Panel D-sub 25-pin cables (5 m (16 feet), (1) Key top removing tool (1) General Display panel attachments (2) Switch chips (15) Screws (+B4 × 6) (8) Power requirements Operation and Installation Guide (1) 100 to 240 V AC ±10%, 50/60 Hz Power consumption 1.0 A max.
Page 64
Specifications BKDS-7002 Source Name BKDS-7030 Key Frame Control Display Unit Panel Unit Product configuration Power requirements LE-147 board (2) 5 V ±0.2 V DC, 12 V ±0.5 V DC LE-148 board (3) Power consumption LE-180 board (1) 5 W max. DC-92 board (6) Temperature range Power requirements...
Page 65
BKDS-7033 Memory Recall BKDS-7090 Redundant Power Control Panel Unit Supply Unit Power requirements Power requirements 5 V ±0.2 V DC, 12 V ±0.5 V DC Primary 100 to 240 V AC ±10%, 50/60 Hz Power consumption Secondary 5 V ±0.2 V DC (9 A max.) 5 W max.
Page 66
Specifications BKDS-7103 12 Input Serial BKDS-7110 Blank Input Adaptor Digital Board Board General General Power requirements Power requirements ±5 V ±0.2 V DC, 3.3 V ±0.2 V DC ±5 ±0.2 V DC, 3.3 V ±0.2 V DC Power consumption Power consumption 33 W max.
Page 67
BKDS-7111 Analog Composite BKDS-7113 Serial Digital Input Input Board Board General General Power requirements Power requirements ±5 V ±0.2 V DC, 3.3 V ±0.2 V DC ±5 V ±0.2 V DC, 3.3 V ±0.2V DC Power consumption Power consumption 2 W max. 3 W max.
Specifications BKDS-7133 Chromakey Analog BKDS-7161 Analog Composite Component Input Board Output Board General General Power requirements Power requirements ±5 V ±0.2 V DC, 3.3 V ±0.2 V DC ±5 V ±0.2 V DC, 3.3 V ±0.2 V DC Power consumption Power consumption 22 W max.
BKDS-7163 Serial Digital Output BKDS-7250 PP/DSK Board Board Power requirements ±5 V ±0.2 V DC , 3.3 V ±0.2 V DC General Power consumption 17 W max. (5 V) Power requirements Temperature range ±5 V ±0.2 V DC, 3.3 V ±0.2 V DC Operation guaranteed: 5°C to 40°C (41°F to 104°F) Power consumption Performance guaranteed: 10°C to 35°C (50°F to...
Specifications BKDS-7271 Fine Key/Key Border BKDS-7340 Control Panel Unit Board Power requirements DSK board: 5 V ±0.2 V DC, 3.3 V Power requirements ±0.2 V DC ±5 V ±0.2 V DC , 3.3 V ±0.2 V DC Control panel: 5 V ±0.2 V DC, 12 Power consumption V ±0.5 V DC 5.5 W max.
BKDS-7420 Color Correction BKDS-7445 Frame Memory Board Adaptor Board Power requirements Power requirements 5 V ±0.2 V DC, 3.3 V ±0.2 V DC 5 V ±0.2 V DC, 3.3 V ±0.2 V DC Power consumption Power consumption 5 W max. 5 W max.
Specifications BKDS-2031 Chromakey Board BKDS-2032 Chromakey Upgrade Board General General Power requirements 5 V ±0.2 V DC, 3.3 V ±0.2V DC Power requirements Power consumption 5 V ±0.2 V DC, 3.3 V ±0.2 V DC 10 W max. Power consumption Temperature range 13 W max.
BKDS-2041 Frame Memory Board Power requirements 5 V ±0.2 V DC, 3.3 V ±0.2 V DC Power consumption 16 W max. Temperature range Operation guaranteed: 5°C to 40°C (41°F to 104°F) Performance guaranteed: 10°C to 35°C (50°F to 95°F) Storage: –20°C to +60°C (–4°F to +140°F) 317 ×...
Page 75
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any...