Specifications - GE ATP2100 Installation Instructions Manual

Specifications

Notices
)
*( 6HFXULW\
‹!#ÃB@ÃTrpˆ…v‡’ÃDpÃ8‚p‚…qÃv†ÃhÇ…hqr€h…xÂsÃB@ÃTrpˆ…v‡’ÃDpÃ6yy‡ur…Áh€r†Ãh…rÇ…hqr€h…x†Ã‚sÇurv…r…†Ã6yyÃ…vtu‡†Ã…r†r…‰rq
6
Note
If the new touchpad unit number was previously learned by the panel, communication between the
touchpad and the panel begins immediately. However, if the new touchpad unit number has never been
learned by the panel, continue with step 5.
5. Force the panel to scan bus devices as follows:
For systems where this is the only installed touchpad, remove panel AC and battery power,
then re-apply power.
For systems with more than one touchpad, go to another system touchpad and enter 8 +
installer/dealer CODE (default = 4321) + 0 + 1 . The display shows SCANNING BUS
DEVICES, then a time and date display.
The touchpad and all other bus devices should operate correctly and any bus failures should be
cleared.
Note
If the panel still indicates a bus failure the panel may have previously learned a unit number that is no
longer used by any bus device. See the specific panel Installation Instructions for more information on
deleting unused unit numbers.
Compatibility: .......................... Concord, Concord Express, Concord Ultra
Power Requirements: ............... 12 VDC nominal (See Table 1 for additional power requirements.)
Temperature Range: ................. 32°F (0°C) to 120°F (49°C)
Maximum Humidity: ................ 95% relative, non-condensing
Dimensions: ............................. 5.75 in. x 5.75 in. x 1.0 in. (L x W x D)
UL Listings (see note):.............. UL 985 Household Fire Warning System Units
................................................... UL 1023 Household Burglar-Alarm System Units
................................................... UL 1610 Central Station Burglar-Alarm Units
Note
See specific panel Installation Instructions for complete UL installation requirements for the system you
are installing.
FCC Part 15 Information to the User
Changes or modifications not expressly approved by GE Security can void the user's authority to operate the equipment.
FCC Part 15 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
‰
Reorient or relocate the receiving antenna.
‰
Increase the separation between the equipment and receiver.
‰
Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.
‰
Consult the dealer or an experienced radio/TV technician for help.
!&$ÃSrqÃA‚‘ÃS‚hqÃ6…qrÃCvyy†ÃHIÃ$$ !à VT6ÃÉÃ8hhqh)Ã'&&&$#'#ÃUrpuvphyÃTˆƒƒ‚…‡)Ã'&&&!%!#
ATP2100 & ATP2600 Touchpads Installation Instructions
(Commercial Burglary)