Fitting; Removing The Battery; Changing The Tool; Dust/Chip Extraction - Bosch Professional GSR 12V-35 FC Original Instructions Manual

a
h
K
Screwdriving:
a
h
K
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.

Fitting

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Removing the battery (see figure A)
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Bosch Power Tools
GSR 12V-35 FC GFA 12-X GFA 12-B GFA 12-E GFA 12-W
–
2
m/s
–
2
m/s
2
m/s < 2.5
2
m/s
1.5
To remove the battery (5), press both release buttons (4)
and pull the battery downwards out of the power tool. Do
not use force to do this.
Follow the instructions on correct disposal.

Changing the tool

Inserting the application tool (see figure B)
Insert the application tool all the way into the mounting (1).
Fitting the adapter (see figure C)
Remove the application tool.
Insert the adapter into the mounting (1). Turn the locking
ring (14) until it audibly engages.
Inserting the application tool into the adapter GFA 12-E,
GFA 12-X (see figure D)
Insert the application tool all the way into the mounting (1).
The application tool is held in the mounting by means of a
magnet.
GFA 12-B (see figure E)
Open the drill chuck adapter (11) by turning it in direction of
rotation ➊ until the application tool can be inserted. Insert
the application tool.
Firmly tighten the sleeve of the drill chuck adapter (11) by
turning it by hand in direction of rotation ➋. This will auto-
matically lock the drill chuck.
Turning the adapter (see figure F)
Pull the locked adapter approx. 5 mm away from the power
tool. Turn the adapter to the required position and then let it
go.
Removing the adapter (see figure G)
Remove the application tool.
Unlock the adapter in the
mounting (1).

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
English | 17
– 3.5 –
– 1.5 –
< 2.5 – < 2.5
–
1.5 1.5
direction and pull it off the
1 609 92A 4TV | (03.05.2019)
–
–
< 2.5
1.5