Table of Contents
Advertisement
Available languages
Available languages
13
I n s t a l l a t i o n a n d S e t u p
Progressive
Scan
Progressive
Scan Video
provides
the
highest quality
pictures
with less
flickering.
If you
are
using
the
Component
Video
jacks
for
connection
to
a
TV
or
monitor that is
compatible
with
a
progressive
scan
signal,
set
Progressive
Scan
to
On.
To Turn ON
progressive
scan:
Connect
component
out
of the DVD
to
the
input
of
your
monitor/television,
set
your television
or
monitor
to
Component Input.
1. Select
"Progressive
Scan"
on
the DISPLAY
menu
then press B.
2. Select "On"
using
the
v
/
V
buttons.
3. Press ENTER to confirm
your selection.
The confirm
menu
will appear.
Notes:
If your TV does
not
accept
the
Progressive
Scan
format,
the
picture
will appear scrambled if you
try
Progressive
Scan
on
the DVD
Player.
4. When the confirm
menu
appears
on
your
screen
Cancel is
highlighted
as
default. Use the
b
/ B
buttons
to
highlight
Enter.
5.
Pressing
ENTER will
set
the
player
to
Progressive
scan
mode.
Caution:
Once the
setting
for
progressive
scan
output
is
entered,
an
image
will
only
be visible
on a
progressive
scan
compatible
TV
or
monitor. If you
set
Progressive
Scan
to
On in
error,
you
must reset
the unit.
First,
remove
the disc in the DVD
Player.
Next,
press STOP
(
x
)
and hold it for five seconds before
releasing
it.
The video
output
will be restored
to
the standard
setting,
and
a
picture
will
once
again
be visible
on a
conventional
analog
TV
or
monitor.
TV
Output
Select
Set the
player's
TV
Output
Select
options according
to
the TV connection
type.
YPbPr: When your TV is connected with the
COMPONENT VIDEO OUT/PROGRESSIVE SCAN
jacks
on
the DVD
player.
RGB: When your TV is connected with the SCART
(RGB signal) jack.
AUDIO
Each DVD disc has
a
variety
of audio
output
options.
Set the
player's
AUDIO
options according
to
the
type
of audio
system
you
use.
Dolby Digital
/ DTS / MPEG
Bitstream: Select "Bitstream" if you
connect
the
DVD
Player's
DIGITAL OUT
jack
to
an
amplifier
or
other
equipment
with
a
Dolby Digital,
DTS
or
MPEG decoder.
PCM
(for Dolby Digital
/
MPEG):
Select when
connected
to
a
two-channel
digital
stereo
amplifier.
DVDs encoded in
Dolby Digital
or
MPEG will be
automatically
downmixed
to
two-channel PCM
audio.
Off
(for DTS):
If you select
"Off",
the DTS
signal
is
not
output
through
the DIGITAL OUT
jack.
Sample Freq. (Frequency)
If your receiver
or
amplifier
is NOT
capable
of
handling
96 kHz
signals,
select 48 kHz. When this
choice is
made,
this unit
automatically
converts
any
96
kHz
signals
to 48
kHz
so
your
system
can
decode
them.
If your receiver
or
amplifier
is
capable
of
handling
96
kHz
signals,
select 96 kHz. When this choice is
made,
this unit passes each
type
of
signal through
without
any further
processing.
Check the documentation for your
amplifier
to
verify
its
capabilities.
DVD
DivX
DVD
DISPLAY
TV
Aspect
Display
Mode
Move
Enter
Prev.
On
Progressive
Scan
Off
TV
Output
Select
Dolby Digital
Bitstream
PCM
48
kHz
On
Bitstream
DTS
MPEG
Sample Freq.
DRC
On
Vocal
Move
Select
AUDIO
Advertisement
Chapters
Table of Contents
