Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch Control 8311
Summary of Contents for Bosch Control 8311
- Page 1 Operating instructions for users Control unit Control 8311/8313...
-
Page 2: Table Of Contents
3.6.4 Modifying settings ......11 7.1.2 Dialling in to the Bosch MEC Remote Portal..26 3.6.5 Labelling a text field . -
Page 3: Explanation Of Symbols And Safety Instructions
“If the power cable is damaged, it must be replaced by the manufacturer, its customer service department or a similarly qualified person, so that risks are avoided.” Control 8311/8313 – 6720859790 (2020/02) -
Page 4: Product Information
Open Source Software further drainage points (e.g. upstream of the non- This product contains proprietary software by Bosch (licensed according to the Bosch standard licensing conditions) and Open Source return valves). Software (licensed according to the Open Source licensing conditions). -
Page 5: Explanation Of The Terms Used
For a description of this function, refer to the technical documentation for the module. Determined use The control unit controls and monitors heating systems in apartment buildings, residential complexes and other buildings. ▶ Observe country-specific standards and regulations concerning installation and operation! Control 8311/8313 – 6720859790 (2020/02) -
Page 6: Operation Of The Control Unit
Reset button (e.g. high limit safety cut-out, SAFe) Chimney sweep button (Flue gas test) Manual operation button USB connection (e.g. for service purposes) [10] LED status display [11] Type plate [12] F1-, F2 circuit breaker [13] ON/OFF switch [14] Back panel Control 8311/8313 – 6720859790 (2020/02) -
Page 7: Function Buttons And System Status
The start page is then displayed with the system overview. System (Heat distribution) Header with status display, e.g. display disabled Status display of Internet connection (display depends on software version) Status display of the system (display depends on the software version) Control 8311/8313 – 6720859790 (2020/02) - Page 8 Heat source with status display, boiler temperature Footer with navigation symbols [10] Flue gas temperature [11] Information on heat transfer (situation-dependent) [12] Advanced functions of the heat source 1) Set value and actual value (set value in parentheses) Control 8311/8313 – 6720859790 (2020/02)
- Page 9 Field for switching between the display type (old/new display version) on the display [10] Information menu [11] Field for returning to the previous level/screen [12] Field for returning to the system overview [13] Status display of system components Control 8311/8313 – 6720859790 (2020/02)
-
Page 10: Control System
If several menus or functions exist at one level: Fig. 8 Scrolling ▶ Tap the corresponding position (function) on the display with your -or- finger. ▶ Swipe your finger across the display. 50 °C on/off 30 % 12:00 0010006537-002 Fig. 9 Swipe Control 8311/8313 – 6720859790 (2020/02) -
Page 11: Calling Up Submenus
▶ Enter a suitable text for the length of the field. ▶ Confirm entry with To save the changes: Auto ▶ Tap box for Save. To cancel the operation: 12:00 ▶ Tap box for Cancel. 0010008712-001 Fig. 12 Heating circuit view, CSM/CFB series Control 8311/8313 – 6720859790 (2020/02) -
Page 12: Function Keys Of The User Interface
▶ Press and hold the key for 2 seconds. (minimum/maximum boiler temperature, minimum/maximum performance). Only for Control 8311: when using separate burners, the burner control unit cannot be reset via the key. • The maximum boiler temperature cannot be changed in the Flue gas test. -
Page 13: Manual Operation
( Fig. 15, [4]) opens the screen in which WARNING: faults are displayed. Risk of scalding from hot water! Setting the set temperature > 60 °C creates a risk of scalding. ▶ Do not draw off DHW unmixed. Control 8311/8313 – 6720859790 (2020/02) -
Page 14: Setting The Date And Time
• Statuses of safety equipment appears in the footer of the message window. • Temperatures To close the notification window: • Operating modes ▶ Tap at the top on the right. • Status of components • Hours run Control 8311/8313 – 6720859790 (2020/02) -
Page 15: Selection Of Control Units
Further information on the selected control unit Press symbol to return to the previous level/screen of the selected control unit Press symbol to access the selected control unit in the system overview or in the control unit overview Control 8311/8313 – 6720859790 (2020/02) -
Page 16: Settings
– Deleting switching points – Linking heating phases ( Chapter 6.2.4, page 24) – Deleting heating phases • DHW heating • Creating a new DHW program • Creating a new circulation program Table 3 Standard functions Control 8311/8313 – 6720859790 (2020/02) -
Page 17: Advanced Functions For Heating Circuits
Off/On Setting that specifies how long the DHW The holiday period can be set via a year settings are not taken into account. calendar ( Chapter 5.3.1, page 19). Table 5 Advanced functions for DHW Control 8311/8313 – 6720859790 (2020/02) -
Page 18: Information On The Standard Functions And The Advanced Functions
▶ Select desired Operating mode. This change does not affect the other parameters. The temperatures in The selected Operating mode is applied. the other operating modes are not affected. If you reselect the function, the value is displayed again. Control 8311/8313 – 6720859790 (2020/02) -
Page 19: Manual Operation
In this operating mode, the heating circuit is switched off. The holiday function must be set for every heating circuit (DHW heating) ▶ Select the heating circuit in which the temperature is to be changed. separately. ▶ Select operating mode Off. Control 8311/8313 – 6720859790 (2020/02) -
Page 20: Party Function
(constant setback mode) Button with LED for automatic mode (heating mode and setback modes as programmed) Button with LED for manually selecting heating mode (constant heating mode) LED for summer mode (only DHW heating is possible) Control 8311/8313 – 6720859790 (2020/02) -
Page 21: Advanced Functions For Dhw
During continuous operation, the DHW circulation pump operates continuously in heating mode, and is switched off in setback mode. To make the setting go to Domestic hot water > Advanced functions ( Chapter 4.3, page 17). Control 8311/8313 – 6720859790 (2020/02) -
Page 22: Time Program
Program Dropdown list Program Indoor temperature Operation mode Save Active time program Cancel [10] Switching point [11] Clock [12] Set room temperature for heating mode [13] Set room temperature for setback mode [14] Indoor temperature Control 8311/8313 – 6720859790 (2020/02) -
Page 23: Modifying The Standard Program
▶ Tap box for Save. ▶ Tap Prog field again. ▶ Tap Program selection box. ▶ Select Family from the list. ▶ Tap Day of week selection box. ▶ Select Saturday to Sunday. ▶ Tap box for Save. Control 8311/8313 – 6720859790 (2020/02) -
Page 24: Dhw Time Program
▶ In the Circulation time program field, tap the Auto field. ▶ Tap box for Program setting. ▶ Adjust Day of week and Program in the same manner as the time program ( Chapter Creating a new DHW time program, page 24). ▶ Tap Save. Control 8311/8313 – 6720859790 (2020/02) -
Page 25: Connectivity
Britain) • Password (The password must be at least 12 characters long in keeping with Bosch rules, and include at least one special character in addition to upper and lower case letters.) • Confirm password (When you enter the password again, it must exactly match the password previously entered.) -
Page 26: Dialling In To The Bosch Mec Remote Portal
Cleaning the control unit 7.1.2 Dialling in to the Bosch MEC Remote Portal Operating and fault displays Following registration, you can log in via the following page: ▶ Call up log-in mask via https://www.mec-remote.com/register. WARNING: ▶ Fill out the mask. -
Page 27: Faults
• The DHW heating is running for too ▶ Check DHW heating. long. • Heat sources are delivering ▶ Check the heat source. insufficient thermal energy or are shut down. • Room temperature sensor has ▶ Phone Service. been adjusted incorrectly. Control 8311/8313 – 6720859790 (2020/02) - Page 28 Burner is not going into operation. • Internal safety device of burner has ▶ Phone Service. safeguard for ZM5311 burner triggered. output • Current consumption by the burner is too high. Table 7 Unit troubleshooting Control 8311/8313 – 6720859790 (2020/02)
-
Page 29: Environmental Protection And Disposal
Data Protection Officer, Information Security and Privacy (C/ISP), This symbol means that the product must not be disposed Robert Bosch GmbH, Postfach 30 02 20, 70442 Stuttgart, GERMANY. of with other waste, and instead must be taken to the waste... - Page 32 Bosch Thermotechnik GmbH Junkersstrasse 20-24 D-73249 Wernau www.bosch-thermotechnology.com...