Table of Contents
Advertisement
Quick Links
High Lift Collection, Parking Stand Kit, and Carrier
Frame
Groundsmaster
Model No. 30818
Model No. 30866—Serial No. 315000001 and Up
Model No. 30869—Serial No. 315000001 and Up
Important: For machines with a Kubota engine, kit 30801 must be installed on the machine. For machines with a
Yanmar engine, kit 30898 must be installed on the machine.
This product contains a chemical or chemicals known to the State of California to
This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at
the back of this publication.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
Replace any decal that is damaged or lost.
1. Crushing hazard—secure the cylinder locks.
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
360 4-Wheel Drive Multi-Purpose Machine
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
132-4868
Register at www.Toro.com.
WARNING
CALIFORNIA
1. Crushing hazard—keep away from actuating parts.
Form No. 3390-683 Rev B
Installation Instructions
132-4867
Original Instructions (EN)
All Rights Reserved *3390-683* B
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro 30818
Summary of Contents for Toro 30818
- Page 1 Frame Groundsmaster ® 360 4-Wheel Drive Multi-Purpose Machine Model No. 30818 Model No. 30866—Serial No. 315000001 and Up Model No. 30869—Serial No. 315000001 and Up Installation Instructions Important: For machines with a Kubota engine, kit 30801 must be installed on the machine. For machines with a Yanmar engine, kit 30898 must be installed on the machine.
- Page 2 132-4866 1. Crushing hazard—keep away from actuating parts. 132-4862 1. Attention—read the Operator’s Manual before performing maintenance; do not transport the vehicle with a full hopper. 2. Only transport the vehicle when the hopper is almost empty. 3. Do not remove the collection system when the hopper is full. 4.
-
Page 3: Installation
Installation Installing the Carrier Frame Kit Installing the Bumpers 1. Move the machine to a level surface, engage the parking brake, shut off the engine, and remove the key from the ignition. 2. Loosen the jam nut on the adjusting bolt on the end of a bumper and lower the adjusting bolt as far as it can (Figure 3. - Page 4 Installing the Carrier Frame 1. Raise the roll bar on the machine and install a pin to secure it on only 1 side of the roll bar. 2. On the other side of the roll bar, install a bolt and nut supplied in the kit into the holes instead of the pin (Figure Figure 2...
- Page 5 5. Move the carrier frame up to the roll bar bracket and secure it using a tabbed pin through the rear hole in the bracket (Figure Note: Place the tab over the end of the pivot bolt. 6. Secure the pivot bolt and tabbed pin using the nut you removed previously (Figure 7.
- Page 6 5. Secure the tabs on the cooler assembly to the carrier-frame plate using 4 bolts and nuts, 2 above and 2 below the assembly (Figure 6. Secure the high-lift-collection assembly to the rear of the carrier frame using 4 bolts, 2 on each side of the assembly (Figure Figure 11...
-
Page 7: Operation
3. Install the deck adapter over the opening in the mower, securing it with the pin assembly and nut as shown in Figure g029474 Figure 14 3. Remove the nut and pin assembly securing the deck adapter to the mower and remove the adapter (Figure 13);... -
Page 8: Greasing The Machine
WARNING The hopper may lower when in the raised position, crushing anyone under it. Install the cylinder locks before performing maintenance that requires the hopper to be in the raised position. Greasing the Machine 1. Lower the hopper and shut off the engine of the machine. - Page 9 Adjusting the Closing Force 1. Lift the hopper and open the hopper door. 2. Put the lowering safeguard in place (Figure 16). 3. Remove both cylinders on the rod-side end. 4. Loosen the locknuts on the cylinder rods. 5. Adjust the length as needed. 6.
-
Page 10: Removing The Fan
Removing and Installing the Turbine Fan Removing the Fan 1. Remove the turbine fan cover (Figure 12). 2. Remove the central fastening bolt of the fan (Figure 19). Figure 19 1. Turbine housing 3. Fan 2. Drive shaft with key 3. -
Page 11: Troubleshooting
There is a strong vibration when the 1. The fan blades are out of balance. 1. Contact your Toro Distributor. blower is running. The fan turns off while operating the 1. The hopper is open. - Page 12 Notes:...
- Page 13 Notes:...
- Page 14 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 15 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.