Panasonic Live Production Suite Series Operating Manual page 47

2
Turn on the power of the Control Panel AV-HS60C2/AV-HS60C4 while pressing the <KEY1> button, <KEY4> button, and <KEY1
TRNS> button in the KEY operation section of the ME line at the top.
The Control Panel AV-HS60C2/AV-HS60C4 is booted in the network setting mode.
Part of the status display and the source display in the ME line at the top will become as follows when it goes into the network setting mode.
f Status display: Setting item is displayed.
The setting item is switched every time the <AUTO> button in the ME line at the top is pressed.
Display
IP
MSK
GTW
MIP
f Source display: Setting value is displayed.
The value will increase by pressing the A bus XPT button under the setting value.
The value will decrease by pressing the B bus XPT button under the setting value.
3
Set each item.
Change the setting value for each setting item, and confirm by pressing the <CUT> button in the ME line at the top.
f The <CUT> button will light up in green when the setting is correctly made.
f The <CUT> button will light up in red when the setting is not correctly made.
f The changed setting value is not confirmed when the setting item is switched without pressing the <CUT> button.
f When the value of the IP address is changed and the <CUT> button is pressed, the value is checked against the value of the subnet mask. At this
time, if the binary of the host address is changed to 0 or 1, the changed value is not confirmed. The <CUT> button lights up in red. In this case,
change the value of the subnet mask, and then change the value of the IP address.
4
Turn off the power of the Control Panel AV-HS60C2/AV-HS60C4.
@ NOTE
t For the subnet mask, use the same address as the address set for the <LAN> terminal of the Live Production Suite system.
t Set the IP address that does not overlap with the following IP address.
- The IP address set to other device that is connected to the <LAN1> terminal of the Live Production Suite system
- The IP address set for the <LAN1> terminal of the Live Production Suite system
t If the default setting for the <LAN1> terminal of the Live Production Suite system is not changed, it can be connected as the control panel 2/3 when
the value described in the setting example is set.
t For details on the network setting for the <LAN1> terminal of the Live Production Suite system, refer to "Configuring the network for the Live
Production Suite system".
Configuring the network for the Live Production Suite system
Configure the network for the <LAN1> terminal of the Live Production Suite system.
f The default setting is as follows: IP address: 192.168.0.90, subnet mask: 255.255.255.0, default gateway: No setting
1
Select the <SYS> button → [SYSTEM] → [Network] tab.
2
Set/check [IP Address] and [Subnet Mask] in the [Network] column.
[IP Address]
[Subnet Mask]
3
Check [Default Gateway] and [MAC Address] in the [Network] column.
[Default Gateway]
[MAC Address]
4
Select the <PANEL> button → [OTHER SETTINGS] → [Panel2] tab → [Network] column, and set the IP address of the control
panel 2 to be connected.
[IP Address]: Sets the IP address of the control panel 2 to be connected. (Setting example: 192.168.0.8)
Set this only when the control panel 2 is connected.
5
Select the <PANEL> button → [OTHER SETTINGS] → [Panel3] tab → [Network] column, and set the IP address of the control
panel 3 to be connected.
[IP Address]: Sets the IP address of the control panel 3 to be connected. (Setting example: 192.168.0.9)
Set this only when the control panel 3 is connected.
NOTE
@
t To enable the settings, the system must be rebooted. Set the power to <OFF>, and then set it back to <ON>.
t If you do not connect the control panel or computer to the <LAN1> terminal of the Live Production Suite system, it is not necessary to set up via the
menu.
t If you use the device to be connected with the settings matching the default settings of the <LAN1> terminal of the Live Production Suite system, it is
not necessary to set up via the menu.
Chapter 4 Preparations — Various settings
IP address
Subnet mask
Default gateway
IP address of the connecting Live Production Suite system
This can be changed from a web browser.
For details, contact your dealer.
This can be changed from a web browser.
For details, contact your dealer.
Checks the default gateway.
Checks the MAC address.
Setting item
– 47 –
Setting example
192.168.0.8
255.255.255.0
0.0.0.0
192.168.0.90