Page 1
JIG 3 SPI EXTEND CARD User Manual Released by C hris Gao : : : : Firmware R&D Center Revision 1.0.0.5 October 14, 2011 ASUSTeK Confidential PROPRIETARY INFORMATION This document contains information proprietary to ASUSTeK Computer Inc. Use or disclosure without permission of an offer of ASUSTeK is expressly forbidden.
ASUS JIG Board User Manual Tables of Content JIG3 Board Overview ................... 2 SPI Extend card Overview ................... 3 Update BIOS binary file to Target via SPI extend card if the manufacturer of EC is ENE ......................4 ShareROM Architecture (One file) ................4 Non-ShareROM Architecture (Two files) ..............
ASUS JIG Board User Manual SPI Extend card Overview Front Back To Notebook To Notebook To EPC Notebook Small keyboard Down connector. Notebook Big keyboard Down connector. Notebook Small keyboard Up connector Notebook Big keyboard Up connector EPC Big keyboard Down connector.
ASUS JIG Board User Manual Update BIOS binary file to Target via SPI extend card if the manufacturer of EC is ENE 3.1 ShareROM Architecture (One file) Please Reference Appendix A Step 1: Remove all power sources (include battery and power supply) from target board.
Page 6
ASUS JIG Board User Manual Step 6: Set SW1 to 0000. Step 7: Press POWER button to turn on power. Power led will turn on. Step 8: Check LED4 will show 00. Step8 Step9: Check all connecter are ready. Step9...
Page 7
ASUS JIG Board User Manual Step 10: Run ASUS_WinFlash utility. Step 11: The Log will show the project name that have connect target board and SPI extend card. If it didn’t be connected yet, please exit ASUS_WinFlash and go to Step1...
Page 8
ASUS JIG Board User Manual Step 13: Check the USB Device “Asus JIG3” is Plug-In Flash of SPI extend card Check Check Check Step 13 Step 14: Check Protect NVRAM to Protect GPNV (Appendix A).(Can choose protect it or not)
Page 9
ASUS JIG Board User Manual Step 17: When this message show on the screen, choose pre backup BIOS ROM before burning or not. Step 17 ASUSTeK Confidential October 14, 2011...
Page 10
ASUS JIG Board User Manual Step 18: When this message show on the screen, turn-on EC power. (Plug-on Power source) And then, show to start burning BIOS ROM. Step 18 Step 19: After burning done, press POWER button again to turn off main power and turn off the ASUS_WinFlash utility.
ASUS JIG Board User Manual Non-ShareROM Architecture (Two files) Please reference Appendix A Step 1~Step14: The same as chapter 3.1. Step 15: Press LoadFile icon to load EC ROM & BIOS ROM file. Step 16: Press AutoBurn icon to burn EC ROM & BIOS ROM file to Target board.
Page 12
ASUS JIG Board User Manual Step 18: When this message show on the screen, turn-on EC power. (Plug-on Power source) Step 18 Step 19: This message notify to start burning EC ROM Step 19 ASUSTeK Confidential October 14, 2011...
Page 13
ASUS JIG Board User Manual Step 20: When this message show on the screen, turn-off EC power. (Plug-out Power source) Step 20 Step 21: When this message show on the screen, turn-on EC power again. (Plug-on Power source again) Step 21...
Page 14
ASUS JIG Board User Manual Step 22: This message notify to start burning BIOS ROM Step 22 Step 23: After burning done, press POWER button again to turn off main power and turn off the ASUS_WinFlash utility. At this time you can remove all devices form target board.
ASUS JIG Board User Manual Update BIOS binary file to Target if the manufacturer of EC is ITE Please reference another SOP ASUSTeK Confidential October 14, 2011...
ASUS JIG Board User Manual Read Target board’s BIOS ROM 5.1 Read Target board’s BIOS ROM via SPI extend card if the manufacturer of EC is ENE Step 1: Remove all power sources JIG Board (include battery and power supply) from target board.
Page 17
ASUS JIG Board User Manual Step 6: Set SW1 to 0000. Step 7: Press POWER button to turn on power. Power led will turn on. Step 8: Check LED4 will show 00. Step 9: Run ASUS_WinFlash utility. Step 8 Step 10: The Log will show the project name that have connect target board and SPI extend card.
Page 18
ASUS JIG Board User Manual Step 12: Press Read Rom icon to read BIOS ROM from target board. Step 13: When this message show on the screen, turn-on EC power(Plug-on Power source) Step 13 Step 14: After read BIOS ROM from...
ASUS JIG Board User Manual 5.2 Read Target board’s BIOS ROM if the manufacturer of EC is ITE Please reference another SOP ASUSTeK Confidential October 14, 2011...
ASUS JIG Board User Manual Example 6.1 Update BIOS binary file to Target on ShareROM architecture via SPI extend card if the manufacturer of EC is ENE Step 1 Remove all power sources Step 2~8 Connect all cable and turn on JIG3 power...
Page 21
ASUS JIG Board User Manual Step 9 Check all connecter Check Step 10~13 Check Check Check Run ASUS_WinFlash utility and check all information ASUSTeK Confidential October 14, 2011...
Page 22
ASUS JIG Board User Manual Step 14 Check Check Protect NVRAM to Protect GPNV (Appendix A). Step 15 Load file ASUSTeK Confidential October 14, 2011...
Page 23
ASUS JIG Board User Manual Step 17 Press AutoBurn and when this message show on the screen, choose pre backup BIOS ROM before burning or not Step 18 When this message show on the screen, turn-on EC power ASUSTeK Confidential...
Page 24
ASUS JIG Board User Manual Step 18 Turn-on EC power Step 19 Check After burning done, check “Auto Flash OK!” → ASUSTeK Confidential October 14, 2011...
ASUS JIG Board User Manual 6.2 Read Target board’s BIOS ROM The Step 1~11 is the same as chapter 4.1 Step 12~13 Press ReadRom and turn on EC power Step 14 After reading, save file ASUSTeK Confidential October 14, 2011...
ASUS JIG Board User Manual Appendix A KeyBoard Connector Up Connector: The pin connect on the up side Down Connector: The pin connect on the down side ASUSTeK Confidential October 14, 2011...
ASUS JIG Board User Manual KeyBoard Type Big Keyboard: keyboard have extend numeric keypad extend numeric keypad Small Keyboard: keyboard have no extend numeric keypad ASUSTeK Confidential October 14, 2011...
ASUS JIG Board User Manual EC Manufacturer ID EC=ENE : The Manufacturer of EC is ENE EC=ITE : The Manufacturer of EC is ITE Platform Platform=HR: The platform is Huron River. Normally, the manufacturer of EC on Huron River is Platform=NONHR: The platform is not Huron River.
ASUS JIG Board User Manual Architecture ShareROM: The EC ROM and the BIOS ROM is the same ROM. So, there is only one BIOSBIN file to burn on BIOS ROM. Non-ShareROM: The EC ROM and the BIOS ROM are not the same ROM. So, there are files that have to burn.
ASUS JIG Board User Manual Appendix B Build “ENEProjectList.ini” file Step 1:Open the “ENEProjectList.ini”, in the file path “\\INI\ ENEProjectList.ini” Step 2:Type Project Name into [ that all of the manufacturer of EC in these projects are ENE ex. [TestProject1]...