GE AF-650 GP Programming Manual page 47

Parameter Descriptions
E-10 Accel Time 2
Range:
3 3
E-11 Decel Time 2
Range:
3.00 [0.01
s - 3600
*
s]
E-12 Accel Time 3
Range:
3.00 s [0.01 -
*
3600 s]
E-13 Decel Time 3
Range:
3.00 [0.01
s - 3600
*
s]
E-14 Accel Time 4
Range:
3.00 [0.01 -
s 3600 s]
*
46
AF-650 GP Programming Guide
Function:
the output current does not exceed the current
limit in F-43 Current Limit during ramping. The
value 0.00 corresponds to 0.01 s in speed mode.
See decel time in E-11 Decel Time 2.
t acc s x n s RPM
Par . E − 10 =
ref RPM
Function:
Enter the decel time from the rated motor speed
n to 0 RPM. Choose a decel time such that no
s
over-voltage arises in the inverter due to
regenerative operation of the motor, and such
that the generated current does not exceed the
current limit set in F-43 Current Limit. The value
0.00 corresponds to 0.01 s in speed mode. See
accel time in E-10 Accel Time 2.
t dec s x n s RPM
Par
. E − 11 =
ref RPM
Function:
Enter the accel time from 0 RPM to the rated
motor speed n . Choose a accel time such
s
that the output current does not exceed the
current limit in F-43 Current Limit during
ramping. The value 0.00 corresponds to 0.01
s in speed mode. See decel time in
E-13 Decel Time 3.
Function:
Enter the decel time from the rated motor speed
n to 0 RPM. Choose a decel time such that no
s
over-voltage arises in the inverter due to
regenerative operation of the motor, and such
that the generated current does not exceed the
current limit set in F-43 Current Limit. The value
0.00 corresponds to 0.01 s in speed mode. See
accel time in E-12 Accel Time 3.
t dec s x n s RPM
Par
. E − 13 =
ref RPM
Function:
Enter the accel time from 0 RPM to the rated
motor speed n . Choose a accel time such that
s
the output current does not exceed the current
limit in F-43 Current Limit during ramping. The
value 0.00 corresponds to 0.01 s in speed mode.
See decel time in E-15 Decel Time 4.
t acc s x n s RPM
Par
. E − 14 =
ref RPM
E-15 Decel Time 4
Range: Function:
3.00 [0.01 Enter the decel time from the rated motor speed
s - 3600 n to 0 RPM. Choose a decel time such that no
*
s
s] over-voltage arises in the inverter due to
regenerative operation of the motor, and such
that the generated current does not exceed the
current limit set in F-43 Current Limit. The value
0.00 corresponds to 0.01 s in speed mode. See
accel time in E-14 Accel Time 4.
Par
. E − 15 =
3.4.3 E-2# Digital Output
Parameters to configure terminal 27 and 29 digital outputs
controlled by serial communications and to configure Relay
1 and Relay 2.
Parameters for configuring the output functions for the
output terminals. The 2 solid-state digital outputs are
common for terminals 27 and 29. Set the I/O function for
terminal 27 in E-51 Terminal 27 Mode, and set the I/O
function for terminal 29 in E-52 Terminal 29 Mode. These
parameters cannot be adjusted while the motor is running.
[0] No operation Default for all digital outputs and relay
outputs
[1] Control ready The control board receives supply
voltage.
[2] Drive ready The frequency converter is ready for
operation and applies a supply signal on
the control board.
[3] Drive ready / The frequency converter is ready for
remote control operation and is in Auto mode.
[4] Enable / no Ready for operation. No start or stop
warning command is been given (start/disable).
There are no warnings.
[5] Drive running Motor is running.
[6] Running / no Output speed is higher than the speed
warning set in H-81 Min Speed for Function at Stop
[RPM]. The motor is running and there
are no warnings.
[7] Run in range / Motor is running within the programmed
no warning current and speed ranges set in
H-70 Warning Current Low to
H-73 Warning Speed High. There are no
warnings.
[8] Run on Motor runs at reference speed.
reference / no
warning
[9] Alarm An alarm activates the output. There are
no warnings.
[10] Alarm or An alarm or a warning activates the
warning output.
DET-618C
t dec s x n s RPM
ref RPM