Sony MEX-DV2000 Installation/Connections

3-099-739-21 (1)
Multi Disc Player
Многодисковый
проигрыватель
Installation/Connections
Установка/Подсоединение
* not supplied
B
* not supplied
MEX-DV2000
© 2007 Sony Corporation Printed in Thailand
  
  
* not supplied
× 2
Cautions
 
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the power supply lead  to the unit and
speakers before connecting it to the auxiliary power
connector.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to in su late any loose un con nect ed leads with
electrical tape for safety.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
Front speaker stereo components, the connected car circuit's rating
Power amplifi er
must be higher than the sum of each component's fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts list
Rear speaker
CD changer
• The numbers in the list are keyed to those in the
instructions.
• The bracket  and the protection collar  are
attached to the unit before shipping. Before mounting
the unit, use the release keys  to remove the bracket
 and the protection collar  from the unit. For
Rotary commander RM-X4
Center speaker
details, see "Removing the protection collar and the
bracket ()" on the reverse side of the sheet.
• Keep the release keys  for future use as they
are also necessary if you remove the unit from
your car.
Active subwoofer
A
Monitor* FRONT VIDEO
SUB OUT
*
OUT
REAR VIDEO
Monitor*
OUT
*
CENTER REAR AUDIO
OUT OUT
Monitor*
*
FRONT VIDEO
BUS AUDIO IN OUT
BUS CONTROL IN REAR VIDEO
OUT
Monitor*
*
Monitor*
*
FRONT VIDEO
BUS AUDIO IN
OUT
Source selector*
*
XA-C40
REAR VIDEO
BUS CONTROL IN
OUT
Monitor*
*
Caution
Handle the bracket  carefully to avoid injuring your Warning
fi ngers. If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power supply lead
 may damage the antenna (aerial).
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
• When your car has built-in FM/MW/LW antenna (aerial) in the

Catch
Note • A power antenna (aerial) without a relay box cannot be used
Before installing, make sure that the catches on both sides of
the bracket  are bent inwards 2 mm. If the catches are straight
Memory hold connection
or bent outwards, the unit will not be installed securely and may
When the yellow power input lead is connected, power will
spring out.
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
Connection example
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
Notes (-A) • Do not connect the speaker terminals to the car chassis, or
• Be sure to connect the ground (earth) lead before connecting
the amplifi er.
• The alarm will only sound if the built-in amplifi er is used. • Do not connect the ground (earth) lead of this unit to the
Tip (-B- )
• Do not attempt to connect the speakers in parallel.
For connecting two or more CD changers, the source selector
• Connect only passive speakers. Connecting active speakers
XA-C40 (not supplied) is necessary.
• To avoid a malfunction, do not use the built-in speaker leads
Connection diagram
• Do not connect the unit's speaker leads to each other.
 To AMP REMOTE IN of an optional power Notes on connection
• If speaker and amplifi er are not connected correctly, "FAILURE"
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
• If you are to use the monitor for the rear seats, connect the
 To the interface cable of a car telephone
 To the parking brake switch cord
 To the microphone (not supplied)
FRONT AUDIO OUT
FRONT VIDEO OUT
Monitor (not supplied) BUS AUDIO IN
CENTER OUT
REAR AUDIO OUT SUB OUT

* 2
REAR VIDEO OUT
Fuse (10 A)
6
MIC IN *
* 1 from car antenna (aerial)

Max. supply current 0.3 A Blue/white striped
AMP REM
Light blue
ATT
PARKING Light green
BRAKE
* 5
See "Power connection diagram" on the reverse
side for details.
DC when you turn on the tuner, or when you activate the AF
(Alternative Frequency) or TA (Traffi c Announcement) function.
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.

with this unit.
adequate power handling capacities to avoid its damage.
connect the terminals of the right speakers with those of the
left speaker.
negative (–) terminal of the speaker.
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
parking brake switch cord to the ground (earth).
Monitor (not supplied)
* 2
Source selector
(not supplied)
Supplied with the CD changer
* 4
XA-C40
* 2
REMOTE
IN
* 3
BUS
CONTROL IN

5
from the car's power connector
4 6
Yellow continuous power supply
4
Blue power antenna (aerial) control
5
Orange/White switched illumination power supply
6
Red switched power supply
7
Black ground (earth)
8
Positions 1, 2 and do not have pins.
Примечания (-A)



Совет (-B- )










Пpимeчaниe


* 1 Note for the antenna (aerial) connecting
If your car antenna (aerial) is an ISO (International Organization for
Standardization) type, use the supplied adaptor  to connect it. First
connect the car antenna (aerial) to the supplied adaptor, then connect
it to the antenna (aerial) jack of the master unit.
* 2 RCA pin cord (not supplied)
Insert with the cord upwards
* 3
* 4 Supplied with XA-C40
* 5 For details on connecting to the parking brake switch cord, see
"Connecting the parking brake cord ()" on the reverse side.
* 6 For details on connecting to the MIC input cord, see "Connecting a
microphone ()" on the reverse side.
*
1

* 2
* 3
* 4
* 5
()
* 6
()
1 3 5 7
from the car's speaker connector
2 4 6 8
Speaker, Rear, Right
1 +
Purple
Speaker, Rear, Right
7
2 –
Speaker, Front, Right
3 +
Gray
Speaker, Front, Right
4 –
Speaker, Front, Left
5 +
8
White
Speaker, Front, Left
6 –
Speaker, Rear, Left
7 +
Green
Speaker, Rear, Left
8 –
Negative polarity positions 2, 4, 6 and 8 have striped leads.
О проводах управления и питания
Подсоединение для поддержки памяти
Примечания относительно подсоединения
громкоговорителей
Примечания отноcитeльно подcоeдинeния