Bosch GTA 2500 Compact Professional Original Instructions Manual page 9

OBJ_BUCH-1648-002.book Page 9 Monday, December 12, 2016 2:14 PM
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Saw stand
Article number
Length of saw stand without table
extension
Length of saw stand with table ex-
tension
Height of saw stand
Max. carrying capacity
(power tool + workpiece)
without table extension
– Attachment set
Max. carrying capacity
(power tool + workpiece)
with table extension
– Attachment set
– Per table extension
Weight according to EPTA-
Procedure 01:2014
Assembly
Delivery Scope
Please also observe the representation of
the delivery scope at the beginning of the op-
erating instructions.
Before assembling the saw stand, check if all
parts listed below are provided:
No. Designation
Saw stand GTA 2500 Compact
5 Attachment set
1 Workpiece support
10 Open-end spanner
15 Power tool fastening kit
consisting of:
– Hexagon bolt (M8 x 45)
– Washer
Assembling the Saw Stand
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packaging material.
Setting Up the Saw Stand (see figures A1 – A2)
– Lay the saw stand upside down on the floor (legs facing up-
ward).
– Push the locking pin 11 in and tilt the leg upward until the
locking pin can be heard to engage.
– Repeat this workstep with the other three legs.
– Turn around the saw stand to the working position.
– Ensure that the saw stand is stable and that all locking pins
have engaged.
Bosch Power Tools
The saw stand is easily aligned with the height-adjustable leg
8.
– Screw the leg in or out until the saw stand is aligned level
and all four legs face against the floor.
Mounting the Workpiece Support (see figure B)
GTA 2500 Compact
– Insert the workpiece support 1 into the table extension 3.
3 601 M12 400
– Tighten the locking knob 2 to lock the workpiece support.
– Repeat the worksteps with the second workpiece support.
mm 1050
Preparing the Saw Stand
mm 2500
Preparing the Attachment Sets (see figures C1 – C4)
mm 862
– To release the attachment sets 5, press buttons 12 each
and open the levers 13.
– Measure the distance x between the mounting holes and
your power tool.
kg 250 – Position the attachment sets 5 centred on the saw stand
and at the matching clearance x to each other.
– Lock the levers 13 again. The attachment sets are now
firmly positioned on the saw stand.
kg 150
Fastening the Power Tool to the Attachment Sets
kg 50
(see figure D)
– Position the power tool in the transport position.
kg 15.8
Notes on the transport position are given in the operating
instructions of the respective power tool.
– Position the movable nuts 14 in the attachment sets so
that they match the mounting holes of the power tool.
– Screw the attachment set and the power tool with the hex-
agon bolts and the washers from the fastening kit 15 using
the provided open-end spanner 10.
Operation
Working Advice
Quantity
Do not overload the saw stand. Always observe the maximum
1
carrying capacity of the saw stand and the two table exten-
2
sions.
2
Always hold the workpiece firmly, especially the longer and
1
more heavy section. After cutting through the workpiece, the
centre of gravity may become dislocated in such an unfavour-
able manner that the saw stand tips over.
4
Extending the Saw Stand (see figures E1
4
Long workpieces must be underlaid or supported at their free
end.
– Place your long workpiece onto the saw table of the power
tool.
– Loosen locking knob 7 and pull the table extension 3 out to
the desired clearance.
– Retighten the locking knobs again.
– Loosen locking knob 2 and adjust the height of the work-
piece support 1 so that the workpiece rests level.
– Retighten the locking knobs again.
English | 9
E2)
–
1 609 92A 2W2 | (12.12.16)