Hitachi SINELINK 24G User Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Radio
  5. SINELINK 24G
  6. User manual
Hitachi SINELINK 24G User Manual

Hitachi SINELINK 24G User Manual

150mbps high-speed radio link
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
150Mbps High-speed Radio Link
User's Manual
Please read ahead of the use.

Advertisement

Table of Contents
loading

Related Manuals for Hitachi SINELINK 24G

Summary of Contents for Hitachi SINELINK 24G

  • Page 1 150Mbps High-speed Radio Link User’s Manual Please read ahead of the use.
  • Page 2 SINELINK24G Caution: Changes or modifications not expressly approved by Hitachi Kokusai Electric Inc. could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 3: Table Of Contents

    SINELINK24G 1. INTRODUCTION ................1 1-1 T ..................1 ARGETS 1-2 P ..............1 RODUCT SUMMARY 1-3 F ...................1 EATURES 1-7 N .......2 AME AND EXPLANATION OF MAIN BODY EACH PART 1-8 D .............3 IRECTIVITY OF ANTENNA 1-9 C SINELINK24G............4 ONNECTING 2. INSTALLATION, CONNECTION, SETTING........5 2-1 I ..............5 NSTALLATION...

  • Page 4: Introduction

    SINELINK24G 1. INTRODUCTION This manual describes the use of SINELINK24G. Please read this manual carefully before using the equipment. 1-1 Targets This manual targets the engineer who has knowledge of LAN, TCP/IP, and a WWW browser at the business level. 1-2 Product summary * Using unlicensed 24GHz band, everybody can use SINELINK and install anywhere.

  • Page 5: Name And Explanation Of Main Body Each Part

    SINELINK24G 1-7 Name and explanation of main body each part approximately approximately approximately approximately 29cm 29cm Name explanation Antenna The radio wave emits from the antenna side. The antenna side is turned to the opposing device for set up. Direction Adjustment Scope By looking from the hole in scope, the direction of this antenna is adjusted.

  • Page 6: Directivity Of Antenna

    SINELINK24G 1-8 Directivity of antenna Directivity of antenna Horizontal direction 0.5° Vertical direction 0.5° Antenna pattern Angle(degree) Angle(degree)

  • Page 7: Connecting Sinelink24G

    (3) PoE-PSE connects with Switching-HUB. (4) The terminal GND of SINELINK 24G must connect with grounding conductors. (5) Use the Switching-HUB corresponding to 100Mbps(full-duplex). (6) Ground it through PoE-PSE when you use the STP cable for (2).

  • Page 8: Installation, Connection, Setting

    SINELINK24G 2. Installation, Connection, Setting 2-1 Installation Flow Setting up from PC Install after setting values by WWW browser of PC. (1) Confirm a setting environment. (2) Change IP Address of PC for setting. (3) Setting this product from PC. Preparation Prepare in indoor environment before installation.

  • Page 9: Setting Up From Pc

    (2) Change IP Address of PC for setting. Change IP Address and Subnet Mask of PC for setting to the following values. * IP Address: 192.168.0.1 ~ 192.168.0.254 (without 192.168.0.202) * Subnet Mask: 255.255.255.0 Factory Default of SINELINK 24G * IP Address: 192.168.0.202 * Subnet Mask: 255.255.255.0...
  • Page 10 SINELINK24G (3) Setting this device from PC. Set this device by WWW browser so that the wireless may communicate with the opposite product. setting pages, browse SINELINK entering the URL in the location bar of your browser. http://192.168.0.202/ (factory default). Enter “administrator”...
  • Page 11 SINELINK24G Enter following settings field. Device Name Enter this product name. The field will accept alphanumeric string and has a maximum length of 20 characters. Factory default is all space. Operation Mode Select “Master” “Slave”. wireless communication with opposite product, it is necessary to set one of them "Master"...
  • Page 12 SINELINK24G Subnet Mask Enter Subnet Mask. IP Address Range of Subnet Mask The table on the right Classes shows range Class A 255.0.0.0 Subnet Mask. ~ 255.255.255.252 Factory default Class B 255.255.0.0 255.255.255.0. ~ 255.255.255.252 Class C 255.255.255.0 Default Gateway ~ 255.255.255.252 Enter Default Gateway.
  • Page 13 SINELINK24G Enter settings each item, and click "Apply" button. The setting is changed, and this device does restart. It takes about 30 seconds until restart is completed. ※example Change IP address of PC to the value that can be communicated with this device.

  • Page 14: Preparation For Installation

    SINELINK24G 2-3 Preparation for installation. (1) Confirm the fit of mounting bracket Confirm the fit of the mounting bracket. “V” There are markings of V and H on the back of the Antenna. If you set the V upward (factory default), then vertically polarized wave...

  • Page 15: Installation

    SINELINK24G 2-4 Installation Fix this product to pole after completion of the preparation and the setting by WWW browser. Mounting kit corresponds to pole phi from 25 to 45mm. In the followings, please do not install. * No line of sight between this products. No radio communication is established under such condition, * Where distance is variable between this products.
  • Page 16 SINELINK24G Outdoor installation example Fix this product to the pole designed for veranda, wall and roof top installation, depending on circumstances. Installation on veranda...
  • Page 17 SINELINK24G (1) Fixing to pole Arrange pole for this product installation. Pole phi is from 25 to 45mm. recommended that pole 10mm or more length less than 700mm Mount bracket : for indoor and less than approx. 70mm 400mm outdoor installation.
  • Page 18 SINELINK24G Scope Look into the scope at a distance of 30cm. Direction adjustment scope several scopes with different diameter. Find opposite product distance 30cm 以上離れて through bigger 30cm or more from the scope scope, then adjust the 覗きます sight of the opposite Scopes アンテナ調整用...
  • Page 19 SINELINK24G Adjustment of horizontal angle Adjust angle of direction to the opposite product looking into scope. Adjust sight opposite product to the horizontal centre of the Adjust horizontal angle hole. Vertical center adjusted accommodation vertical angle. Visual recognition become harder longer the distance to opposite products.
  • Page 20 SINELINK24G Adjustment of vertical angle Look into the adjusting scope correctly and find the proper angle by viewing opposite product. Vertical angle Vertical angle can be adjusted between the range of +/- 15 degrees. In case of 15 degrees, relation between distance and height will be as follows;...
  • Page 21 SINELINK24G Next, fix the product with the fixing pole. Certainly tight the M6 bolt, that Antenna would stably fixed. Fix tightly Next, tight the M6 bolt (4pcs.) to fix the vertical angle of the mounting plate. Fixing Torque of M6 bolt should be 2.36 to 2.74 [N/cm] (24 to 28[kgf/cm])
  • Page 22 SINELINK24G Connect the LAN cable (with water protection cap/ refer to 2-3) Water protection cap Shielded RJ45 connector Check the LAN cable (Check points) quality using Cable = All 8 cable cores are connected straightly. tester. = No communication problem at 100BASE-TX = Cable length should be less than 100m = Communication quality would not be changed in case RJ45 connector portion is touched slightly.

  • Page 23: Connect To Lan Equipments

    SINELINK24G 2-5 Connect to LAN equipments This product complies with IEEE802.3af. It can be connected with LAN equipments, such as Switching HUB, through PoE supply apparatus. (Follow the instruction below) LAN cable =Distance to Switching HUB should be less than 100m. =LAN cable should be straight cable.

  • Page 24: Use Of This Device

    SINELINK24G 3. Use of this device 3-1 Power-On Plugging the LAN cable into IEEE802.3af PoE-PSE enables SINELINK 24G to be powered on and start running. The power output LED of PoE-PSE will light up. 3-2 Power-Off To power off SINELINK 24G, unplug LAN cable plug from IEEE802.3af PoE-PSE.
  • Page 25 ・ User Name is “administrator” ・ Factory Default password is none. (example : Factory Default) Top page is displayed. When you click the item from a left menu, the content displayed right page. (example : Setting "SINELINK 24G" to Device Name)
  • Page 26 SINELINK24G (2) Displays Device Status Click Device Status. Device Status page is displayed. Device Name Device Name displayed. Firmware Version Current firmware version is displayed. MAC Address Address displayed. Serial Number Serial Number of this device is displayed. Date & Time Date and time of this device is displayed.
  • Page 27 SINELINK24G (3) Displays Wireless Status. Click Wireless Status. Wireless Status page is displayed. Operation Mode Operation Mode displayed. Link Status Link Status is displayed. Air Data Rate Data Rate displayed. This device does the adjustment modulation. Data Rate dynamically changes into 50M/100M/50Mbps according situation.
  • Page 28 SINELINK24G Proper value of RSSI The graph of distance and RSSI (theory value) The graph of distance and RSSI (theory value) Proper value of RSSI when it is not is shown right. raining RSSI becomes about -50dBm by ATPC(Auto Power Control) in the short distance.
  • Page 29 SINELINK24G (4) Displays LAN Status. Click LAN Status. LAN Status page is displayed. Link Status Link Status is displayed. Link Speed Link Speed is displayed. Receive Packets Receive Packets displayed. Receive Errors Receive Errors displayed. Click “Clear Counters” button. Receive Packets and Receive Errors returned to 0.
  • Page 30 SINELINK24G (5) Displays Device Log. Click Log Reference. Log Reference page is displayed. Device Log Device displayed. The latest 63 logs from power displayed. Click “Save” button. Device saved to PC. Click “Clear” button. All Logs is cleared.
  • Page 31 SINELINK24G (6) Change password. Click Password Change. Password Change page is displayed. Login Name Login Name displayed. Login Name administrator. New Password New Password (again) Enter New Password. The field will accept alphanumeric string and has a maximum length characters. Factory default is none.
  • Page 32 SINELINK24G (7) Settings date and time. Click Date & Time Setting. Date & Time Setting page is displayed. Date & Time Date and time of this device is displayed. The User needs to set "Date & Time" after Power OFF/ON. New Date &...
  • Page 33 SINELINK24G (8) Initialize the setting. Click Initialization. Initialization page displayed. Current Setting of this device will be reset to factory defaults, this device does restart. takes about seconds until restart is completed.
  • Page 34 SINELINK24G (9) Update firmware of this device. Click Firmware Update. Firmware Update page is displayed. Current Version Current Version displayed. Enter the path and filename firmware update Enter path filename firmware update. Enter path filename, click “Update” button. PC starts to send the firmware file this...
  • Page 35 SINELINK24G (10) Restart this device. Click “Restart” button. Click “OK” button. takes about seconds until restart is completed.

  • Page 36: Appendix

    SINELINK24G 4. Appendix 4-1 Specification Items Specifications Note Applied regulations FCC Part 15.249 Frequency band 24.05 ~ 24.25GHz Number of available channels 24.08 ~ 24.22GHz (20MHz Step) Occupied bandwidth 28MHz Antenna 26cm-square(522 unit) planar Beam angle antenna (All-in-one) degrees or less Gain: 34dBi Vertical/Horizontal polarization...
  • Page 37 SINELINK24G Items Specifications Note Security * Unique and nonpublic radio protocol * Scrambled data * Login password Maintenance The following items can be IEEE802.1Q VLAN controlled by PC based Tag for maintenance tool via LAN cable. can be used. * Firmware update * Reboot * Link ID setting * Status and Log display...

  • Page 38: Rf Channel Allocation Number

    SINELINK24G 4-2 RF channel allocation number 24.05GHz CH1: 24.08GHz CH2: 24.10GHz CH3: 24.12GHz CH4: 24.14GHz CH5: 24.16GHz CH6: 24.18GHz CH7: 24.20GHz CH8: 24.22GHz 24.25GHz...

  • Page 39: Factory Default

    SINELINK24G 4-8 Factory Default Settings Factory Default Memo Name Setting Device Name All space Wireless Operation Mode Slave Settings Link ID (none) LAN Settings IP Address 192.168.0.202 Subnet Mask 255.255.255.0 Default Gateway (none) VLAN VLAN Tag Not Used Password Change (none) 2006.3 Rev.1...

Table of Contents