Important Safety Instructions - Sony DMX-WL1 Reference Manual

G:\Work\SONY\TV\847342S
DMX-WL1T\0724\387708311DMX-WL1\020WAR.fm
010COV.book Page 3 Thursday, July 24, 2008 2:04 PM
Important
Safety
Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this equipment near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other equipment (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
equipment.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
equipment. When a cart is used, use caution when
moving the cart/equipment combination to avoid
injury from tip-over.
13) Unplug this equipment during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the equipment has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the equipment, the equipment has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
USE
AC power cord and other cables
If you damage the AC power cord or other cables, it may result in a fire
or an electric shock. If the AC power cord or any other cables is damaged,
stop using it at once and contact the Sony service center.
s Do not place the equipment where the power cord and cables are
subject to wear or abuse.
s Do not pinch, bend, or twist the cord excessively. The core lines may
be bared and cut, and cause a short-circuit, resulting in a fire or an
electric shock.
s Do not convert or damage the power cord and cables.
s Do not allow anything to rest on or roll over the power cord and
cables.
s Do not pull the power cord and cables.
s Do not move the equipment with the power cord and cables plugged
in.
s Keep the power cord and cables away from heat sources.
s Be sure to grasp the plug when disconnecting the power cord and
cables.
s Do not place the equipment in an area where the cables may become
entangled and catch on your feet or hands.
Wall outlet
Do not use a poor fitting outlet. Insert the plug fully into
the outlet. If it is loose, it may cause arcing and result in
a fire. Contact your electrician to have the outlet
changed.
Cable wiring
For your safety, unplug the AC power cord when wiring cables. Take care
not to catch your feet on the cables. It may damage the equipment.
Electric shock
Do not touch the AC power cord or the equipment
with a wet hand. If you plug/unplug the AC power
cord from the equipment with a wet hand, it may
cause electric shock.
Lightning
For added protection for this equipment during a lightning storm, or when
it is left unattended and unused for long periods of time, unplug it from
the wall outlet. This will prevent damage to the equipment due to
lightning and power line surges.
Small accessories
Keep small accessories out of children's reach.
accessories with this product.
CLEANING
s Clean the AC power plug regularly.
s If the plug is covered with dust and it picks up
moisture, its insulation may deteriorate and
result in a fire.
s Unplug the AC power cord when cleaning this
equipment. If not, it may result in electric
shock.
Clean the casing of the equipment with a dry
soft cloth. Stubborn stains may be removed with a cloth slightly
moistened with a solution of mild soap and warm water. Never use
strong solvents such as thinner or benzine for cleaning.
s If using a chemically pretreated cloth, please follow the instruction
provided on the package.
s Dust the ventilation holes with a dry cloth.
masterpage:Right
Use only the specified
3 3
DMX-WL1
3-877-083-11(1)