Bosch GSH Professional 16-30 Original Instructions Manual page 12

OBJ_BUCH-229-007.book Page 12 Tuesday, December 10, 2013 10:29 AM
12 | English
2000/14/EC: Guaranteed sound power level 106 dB(A).
Conformity assessment procedure according to Annex VI.
Equipment category: 10
Notified body:
TÜV NORD CERT GmbH & Co. KG,
Am TÜV 1, 30519 Hannover
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
10.12.2012
Technical Data
Demolition
Hammer
Article number 3 611 C35 0.. 3 611 C35 1..
Rated power input W
-1
Impact rate min
Impact energy per
stroke according to
EPTA-Procedure
05/2009 J
Tool holder mm
Weight according to
EPTA-Procedure
01/2003 kg
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); sound power level
104 dB(A). Uncertainty K=2 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Chiselling: a =13 m/s , K =1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
1 609 92A 0FC | (10.12.13)
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Carrying Handle
The carrying handle 3 can be turned to any position. Loosen
the knurled nut 4, turn the carrying handle 3 around the ma-
chine axis to the desired position and tighten the knurled nut
4 again.
The carrying handle 3 can also be mounted facing to the other
side. Completely unscrew the knurled nut 4 and then pull out
the hexagon bolt upward. Pull off the carrying handle 3 to the
side and tilt the remaining clamping element by 180°. Mount
the carrying handle 3 in reverse order.
GSH 16-28 GSH 16-30
Changing the Tool (GSH 16-28)
 Before any work on the machine itself, pull the mains
1750 1750
1300 1300
– Clean the tool shank 7 and apply a light coat of grease.
Tools without Shoulder (see figures A–B)
– Pivot the tool retainer 6 upward by approx. 150° and insert
41 41
– Pivot the tool retainer 6 down to lock the tool.
28 30
– Check the latching by pulling the tool.
Tools with Shoulder (see figures C–D)
17.9 16.5
Tools with an insertion length of 152 mm (6") to the shoulder
/II /II can be used.
– Pivot the tool retainer 6 upward by approx. 180° and in-
– Pivot the tool retainer 6 back to the tool to lock it. The
– Check the latching by pulling the tool.
Changing the Tool (GSH 16-30)
(see figures E–F)
 Before any work on the machine itself, pull the mains
– Clean the tool shank 7 and apply a light coat of grease.
2
.
– Pull out the lock bolt 5 and turn it 180° in anticlockwise di-
– Insert the tool into the tool holder 8 to the stop. The groove
– Pull out the lock bolt 5 and turn it 180° in clockwise direc-
– Check the latching by pulling the tool.
plug.
the tool into the tool holder 8.
sert the tool into the tool holder 8.
shoulder 9 must be held by the tool retainer 6.
plug.
rection. Allow the lock bolt 5 to latch again.
of the tool shank 7 must face upward as shown in the figure.
tion. Allow the lock bolt 5 to latch again.
Bosch Power Tools