Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele KFN12823 SD
Summary of Contents for Miele KFN12823 SD
-
Page 1: Installation Instructions
Installation Instructions KFN12823 SD en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions. -
Page 2: Electrical Connection
Electrical connection Failure to follow these Electrocution hazard instructions can result in death, fire, Electrical grounding required. This or electrical shock. appliance is equipped with a three-prong (grounding) polarized Improper connection of the plug for your protection against equipment grounding conductor possible shock hazards. - Page 3 Electrical connection The appliance must be connected to an Do not use an extension cord to electrical outlet that is properly connect the appliance to the power grounded. The electrical installation supply. Extension cords do not must comply with the applicable guarantee the required safety of the electrical code.
-
Page 4: Installation Information
Installation information Location Safe operation of the appliance is This appliance should not be installed only assured if it has been installed near windows where it is exposed to and connected in accordance with direct sunlight or directly adjacent to these operating and installation heat-producing appliances such as an instructions. - Page 5 Installation information Appliances with supplied wall Climate class spacers The appliance is designed for use within a certain climate class (room To achieve the indicated level of temperature range) and should not be energy consumption, you should used outside this range. The climate use the wall spacers that are class for your appliance is stated on the included with a number of...
- Page 6 Installation information Installing the appliance Supporting the appliance door ^ First, remove the cable clip from the back of the appliance. ^ Check that all parts at the back of the appliance can vibrate freely. Carefully bend apart any parts that are touching.
- Page 7 Installation information Appliance dimensions KFN 12823 SD edt/cs-2 1817 mm 600 mm 630 mm* * Dimension without spacers. When the supplied spacers are installed, the depth of the appliance increases by 35 mm.
-
Page 8: Reversing The Door Hinging
Reversing the door hinging The appliance is delivered with Removing the door handles: right-hand door hinging. If left-hand hinging is required, the door hinging must be reversed: To reverse the door hinging, you will need the following tools: When reversing the door hinging, always enlist the help of another person. - Page 9 Reversing the door hinging Removing the appliance doors: the left and pulling the cover forwards. Remove all food and drink from the ^ Turn the retaining plate f 180°. door shelves on the inside of the ^ Fit cover e onto the front of the doors.
- Page 10 Reversing the door hinging ^ Close the lower door. Caution! The lower door is no longer secured in place once the hinge plate has been removed in the next step. ^ Lift each of the plugs l out of the door bushings and reinsert them on ^ Remove the middle bearing pin i by the opposite side.
- Page 11 Reversing the door hinging Reversing the appliance doors: ^ Screw the hinge plate f into place on the opposite side, using only the ^ Pull the entire bearing pin a, outer slotted holes to do so. Do not including washer b and adjustable use the centre screw.
- Page 12 Reversing the door hinging ^ Switch the positions of the covers a and b. ^ Align the door with the appliance housing using the slotted holes in the lower hinge plate. Then firmly tighten the screws. ^ Slide the bearing pin i through the middle hinge plate k and into the lower door.
- Page 13 Reversing the door hinging Reattaching the door handles: Make sure that the sidebar d does It is critical that you follow the not come into contact with the door instructions below for attaching the seal when the door is opened. Over door handle.
-
Page 14: Aligning The Appliance Doors
Aligning the appliance doors The appliance doors can be aligned Align the upper door using the slotted with the appliance housing after being holes in the middle hinge plate: mounted back into place. In order to more clearly illustrate the necessary steps, the following figures do not show a closed door. -
Page 15: Installing The Appliance
Installing the appliance This appliance can be installed in any array of kitchen units. To ensure a uniform height over the entire array, a suitable overhead cabinet a can be installed above the appliance. A ventilation channel with a depth of at least 50 mm must be provided across the entire width of the overhead cabinet to guarantee proper air circulation. - Page 20 KFN 12823 SD edt/cs-2 en - CA M.-Nr. 09 852 800 / 00...