Table of Contents
Advertisement
'14/Jul
3
Transit, Installation (using) environment, Note
[ 1 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[ 2 ] MX-C250/250E/C250F/C250FE/C250FR/C300F/C300W/C300WE
C300A/C300WR(MAIN UNIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[ 3 ] MX-CS11 (500 SHEET Paper Feed Unit) . . . . . . . . . . . . . . . . . . 3 - 1
[ 4 ] Setting, Adjustments, Operation check
[ 5 ] Setup and adjustment data recording . . . . . . . . . . . . . . . . . . . . . 5 - 1
[ 6 ] Necessary works before moving the machine . . . . . . . . . . . . . . . 6 - 1
Parts marked with "
specified ones for maintaining the safety and performance of the set.
INSTALLATION MANUAL
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
MODEL
CONTENTS
" are important for maintaining the safety of the set. Be sure to replace these parts with
SHARP CORPORATION
CODE: 00ZMXC250/I3E
MX-C250/C250E
MX-C250F/C250FE
MX-C250FR
MX-C300F/C300W
MX-C300WE/C300A
MX-C300WR
. . . . . . . . . . . . . . . . . . . . . . . . . . .
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
3
3
3
4 - 1
Advertisement
Table of Contents
Related Manuals for Sharp MX-C250
Summary of Contents for Sharp MX-C250
- Page 1 [ 1 ] CONFIGURATION ........1 - 1 [ 2 ] MX-C250/250E/C250F/C250FE/C250FR/C300F/C300W/C300WE C300A/C300WR(MAIN UNIT) .
- Page 2 Service Manual Machine Environment, Installation, and Transportation 1.Machine Environment and Installation (2)Power voltage Measure the voltage during copying to check that the voltage is in the Before installing the machine, check that the following conditions are range of the specified voltage +/- 10%. satisfied.
- Page 3 F.Note for handling PWB and electronic parts Condensation may form inside the machine causing multiple prob- lems. Make sure machine has proper ventilation. When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against damage by static Humidity RH electricity.
-
Page 4: Transit And Delivery
G.Note for proper drum, developing, fusing and transfer unit handling When handling the OPC drum, developing, fusing units and transfer units, observe the following items. Drum unit To prevent damage to the OPC drum, avoid working on the drum unit in high intensity light areas. When the OPC drum is removed from the machine, cover it with light blocking material. -
Page 5: Configuration
Panel Copy iFAX Scan SAPL Mono MX-C250 25cpm Mono MX-C250F 25cpm Mono MX-C300F 30cpm RSPF Mono MX-C300W 30cpm RSPF Mono MX-C300A 30cpm RSPF *The same speed in both Color/Monochrome. The same speed in both A4/LTR. MX-C250 CONFIGURATION 1- 1... -
Page 6: Option List
‘14/Jul 3. Option list MX-C250, MXC250E, MX-C250F, MX-C250FE, MX-C300E, MX-C250FR, Model Name Model name MX-C300F, MX-C300W, MX-C300W, MX-C300A MX-C300WR Feeding equipment 500-SHEET Paper Feed Unit MX-CS11 Sharpdesk 1 License Kit MX-USX1 Sharpdesk 5 License Kit MX-USX5 Application Sharpdesk 10 License Kit... -
Page 7: C300A/C300Wr(Main Unit)
1) Check that all the parts are in the package. Packed part names Quantity Toner cartridge 1 piece for each color (Other than North America) AC cord 200V series only: 1 piece 120V (USA) Operation Manual 1 set Ferrite core MX-C250 MX-C250/C250E/C250F/C250FE/C250FR/C300E/C300F/C300W/C300WE/C300A/C300WR(MAIN UNIT) 2 – 1... - Page 8 4) Remove fixing tapes and the caps on the developing units. Black Magenta Cyan Yellow NOTE: Be sure to keep the caps. Caps are used when the machine is transferred to the different location. MX-C250 MX-C250/MX-C250E/MX-C250F/MX-C250FE/MX-C300E/MX-C300F/C300W/C300WE(MAIN UNIT) 2 – 2...
- Page 9 When connecting the line cable (to LINE or TEL), wind the line cable two turns or one turn around the included ferrite core as shown in the figure, and connect to the modular jack which is marked with “LINE.” MX-C250 MX-C250/MX-C250E/MX-C250F/MX-C250FE/MX-C300E/MX-C300F/C300W/C300WE(MAIN UNIT) 2 – 3...
- Page 10 Or, fit the STOP key, SCANNER key and COPY key with the Key sheet. (For the machine without FAX) Note : Do not make the buttons overlapped by the Key sheet when putting the key sheet. The Key sheet could be banked by the buttons. MX-C250 MX-C250/MX-C250E/MX-C250F/MX-C250FE/MX-C300E/MX-C300F/C300W/C300WE(MAIN UNIT) 2 – 4...
-
Page 11: Image Quality Check
Make a copy of the servicing color test chart (UKOG- 0326FCZZ/UKOG-0326FC11), and check that they are proper. If the test results are not proper, refer to [5] ADJUSTMENT of the Service Manual and perform the adjustments. MX-C250 MX-C250/MX-C250E/MX-C250F/MX-C250FE/MX-C300E/MX-C300F/C300W/C300WE(MAIN UNIT) 2 – 5... -
Page 12: Mx-Cs11 (500 Sheet Paper Feed Unit)
Plate A) and the screws (Packed items M4x10 P Tight and M4x8 S Tight). Name Quantity Plate A Plate B Fixing screws (M4 x 10 P Tight) Fixing screws (M4 x 8 S Tight) MX-C250 MX-CS11 (500 SHEET PAPER FEED UNIT) 3 – 1... - Page 13 Perform the procedures of 2) - 3) for the printed adjustment pat- RRCB- Manual 1 - 99 tern of each paper feed tray. tim- paper feed 4) Press [OK] key. adjus 1 - 99 The adjustment result becomes valid. RRCB- ment MX-C250 MX-CS11 (500 SHEET PAPER FEED UNIT) 3 – 2...
- Page 14 (Adjust so that the lead edge image from 4.0mm is not copied in either of different copy magnification ratios.) Repeat the above procedures until a satisfactory result is obtained. Scale image 4.0mm position Paper lead edge 100% 200% 10mm MX-C250 MX-CS11 (500 SHEET PAPER FEED UNIT) 3 – 3...
-
Page 15: Setting, Adjustments, Operation Check
With the desk unit installed feed tray Paper size detection Originals size Original table detection mode RSPF mode RSPF operation / S-S mode two sided copy D-S mode S-D mode D-D mode Paper exit operation MX-C250 Setting, Adjustments, Operation check 4 – 1... -
Page 16: Setup And Adjustment Data Recording
- In case of a memory trouble, if the data is not kept, all the adjust- ments must be made again. If the data is kept, the setup values and the adjustment values can be entered without adjustments, shortening the servicing time. MX-C250 Setup and adjustment data recording 5 – 1... -
Page 17: Necessary Works Before Moving The Machine
- Scanner (Optical section) - Paper cassette lift plate Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit. MX-C250 Necessary works before moving the machine 6 – 1... - Page 18 © COPYRIGHT XXXX BY SHARP CORPORATION Since the melting-point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land ALL RIGHTS RESERVED.
- Page 19 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
- Page 20 SHARP CORPORATION Business Solutions CS Promotion Center II Yamatokoriyama, Nara 639-1186, Japan First Edition 2013 September Latest Edition 2014 July...