Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E1C E1K AVR-X1100W P P P AVR-S700W INTEGRATED NETWORK AV RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied.
TECHNICAL SPECIFICATIONS FOR AVR-X1100W n Audio section n Wireless LAN section • Power amplifier Network type Rated output : (wireless LAN standard): Conforming to Wi-Fi®z1 Front : Security : WEP 64 bit, WEP 128 bit 80W+80W(8Ω、20Hz~20kHz with 0.08% T.H.D.) WPA/WPA2-PSK (AES) 120W+120W(6Ω、1kHz with 0.7%...
TECHNICAL SPECIFICATIONS FOR AVR-S700W n Audio section n Wireless LAN section • Power amplifier Network type Rated output : (wireless LAN standard): Conforming to Wi-Fi®z1 Front : Security : WEP 64 bit, WEP 128 bit 75W+75W(8Ω、20Hz~20kHz with 0.08% T.H.D.) WPA/WPA2-PSK (AES) 110W+110W(6Ω、1kHz with 0.7%...
Initialize this unit if you have replaced the microcomputer, one of the parts around the microcomputer, or the digital PCB. Press the power button to turn off the power. AVR-X1100W Hold down buttons "ZONE2 SOURCE" and "DIMMER" at the same time and press the power button to turn on the power.
DISASSEMBLY • Remove each part in the order of the arrows below. • Reassemble removed parts in the reverse order. • Read "Precautions During Work" before reassembling removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Explanatory Photos for DISASSEMBLY • The angles from which the photos are taken are shown by "Photo angle: A, B, C, D". • See the diagram below about the shooting direction of each photograph. • Photographs with no shooting direction indicated were taken from the top of the unit. •...
2. DIGITAL PCB TOP COVER → Proceeding : DIGITAL PCB (1) Remove the screws. (2) Remove the connector wire and FFC. Remove the screws. Front side STYLE PIN CN8221 CN761 CN762 CN619 CON1 CON2 CN741 CN823 CN914 STYLE PIN...
3. RADIATOR ASSY TOP COVER → → Proceeding : DIGITAL PCB RADIATOR ASSY (1) Remove the screws. (2) Remove the screws. Front side 4. SMPS PCB Proceeding : TOP COVER → SMPS PCB (1) Remove the connector wire. Remove the screws. See "EXPLODED VIEW"...
↑ ↑ ↑ Mode channel/video channel. (See page) If there are multiple DENON AV receivers in the same area, this mode stops the other AV receivers from being Remote ID Setup Mode ↑ ↑ ↑ operated concurrently with this device.
↑ ↑ ↑ Mode channel/video channel. (See page) If there are multiple DENON AV receivers in the same area, this mode stops the other AV receivers from being operated Remote ID Setup Mode ↑ ↑ ↑ concurrently with this device.
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up Hold down buttons "DIMMER" and "STATUS" at the same time and press the power button to turn on the power. Press the "STATUS"...
Page 19
i Ethernet 1st Boot Loader, Hardware ID : E t h e r n e t F B L Press the "STATUS" button. * * * * * * - b d o Ethernet 2nd Boot Loader, Rhapsody Flag : E t h e r n e t S B L Press the "STATUS"...
1.4. Error display See the table below for descriptions of displayed errors and countermeasures for these. Display order is q , w , e , r . Condition States Display TROUBLE SHOOTING The model name, brand name and F I R M E R R O R region information written in the firmware are compared to the region settings in...
Page 21
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware Version XXXX - XXXX - XXXX...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Turn the PANEL LOCK and REMOTE LOCK modes on and off. 2.2. Starting up Hold down buttons "TUNER PRESET CH+" and "ZONE2 SOURCE" at the same time and press the power button to turn on the power.
Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 3.2. Starting up AVR-X1100W Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
Page 25
The Video and Audio paths can be checked. The backup data is not rewritten. 3.4.2. Starting up AVR-X1100W Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power. AVR-S700W Hold down buttons "TUNER PRESET CH +", "TUNE -"...
Page 26
A 1 1 : A S S I G N - B i A M P (Amp Assign: Bi-Amp) Input Mode : Auto ・Check of Analog input ⇒ Speaker output. AVR-X1100W Only Sound mode: MULTI CH STEREO Surround Back L/R fig.12 Amp assign : Bi-Amp (※...
Page 31
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL AUDIO BLOCK DA02 DA_FR...
Page 34
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL AUDIO BLOCK DA02 DA_FR...
Page 36
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL AUDIO BLOCK DA02 DA_FR...
Page 38
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL DA_FL AUDIO BLOCK DA02...
Page 40
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL AUDIO BLOCK DA02 DA_FR...
Page 41
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL DA02 AUDIO BLOCK DA_FR...
Page 42
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL AUDIO BLOCK DA02 DA_FR...
Page 44
Media Player CBL/SAT DA_SL DA05 AUDYSSEY MIC(AUTO SETUP) DA_SR DA06 DA_SBL DA07 (FL-H/FL-B/BI-AMP-FL/ZONE-FL) DA_SBR DA08 ZONE2 MUTE AVR-X1100W E3 ONLY (FR-H/FR-B/BI-AMP-FR/ZONE-FR) VOL IC BD3812F VOL IC NJU72340A PRE OUT AD_FL AD_FR MUTE TO DIGITAL DA01 DA_FL AUDIO BLOCK DA02 DA_FR...
Page 45
This mode records and displays an event in which the THERMAL, ASO or DC protection was activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.5.2. Starting up AVR-X1100W ・Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
Page 46
3.5.4. Clearing the Protection History There are two ways to clear the protection history. (1) Start Protection History Display Mode. Press the button "STATUS" to display the protection history. Press and hold the button "DIMMER" for 3 seconds. P R T : D C Press and hold the button "DIMMER"...
Page 47
This mode displays the accumulated operating time, power on count and each protection count. 3.6.2. Starting up AVR-X1100W ・Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
Page 48
This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.7.2. Starting up AVR-X1100W ・ Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
4. Remote ID Setup Mode 4.1. Actions This function allows only the desired AV receiver to be operated if multiple DENON AV receivers are used in the same room. 4.2. Starting up AVR-X1100W ・Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
• This is the same as normal power-on, except that protections are not activated. 5.2. Operations AVR-X1100W ・ Hold down buttons "TUNER PRESET CH +", "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power.
(6) User ID (7) Resume Playback station 7.2. Operations AVR-X1100W ・Hold down buttons "ZONE2 SOURCE" and "DIMMER" for at least 3 seconds while the power is on. AVR-S700W ・Hold down buttons "TUNER PRESET CH +" and "TUNE -" for at least 3 seconds while the power is on.
SERVICE JIGS The following jigs (extension cable kit) are used when repairing the PCBs. Order the jigs from your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for DIGITAL PCB -Items to Be Prepared- 8U- 110084S EXTENSION UNIT KIT 1 Set...
Page 53
(4) Connect the expansion cables. PCB DIGITAL PCB DIFF-AMP Connection table of Board to Board Ref. No. Ref. No. 15pin CN201 DIFF-AMP CN822 DIGITAL Procedure after Replacing the WLAN MODULE. When replaced of the WLAN MODULE(CX870-3B-D60), confirm contents of the following. (1) Part numbers differ depending on the region of the WLAN MODULE.
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Procedure PCB Name Ref. No. Description Remark after Replace- ment DIGITAL IC722 MX25L3206EM2I-12G SOFTWARE: GUI ROM DIGITAL IC751 R5F56108VNFP SOFTWARE: Main DIGITAL IC773 5M80ZT100C5N...
Page 55
1.3. File structure on USB Memory Copy the update files to the USB memory with the following structure: USB memory root Model Name Model Area Product ID AVR-X1100WE3 North America (E3) 000100670100 AVR-X1100WE2/E1 Europe (E2)/Asia (E1) 000100670200 AVR-X1100WE1C China (E1C) 000100670500 AVR-X1100WK Japan (JP)
Page 56
1.5. Start the update. AVR-X1100W ・ Hold down buttons "TUNER PRESET CH +" and "STATUS" at the same time and press the power button to turn on the power. AVR-S700W ・ Hold down buttons "ZONE2 SOURCE" and "TUNE +" at the same time and press the power button to turn on the power.
Page 57
1.10. About the error code See the table below for error codes and details of faults when the firmware is updated through USB memory. Error Details of Error code Display Coping strategies Code Disconnect and connect the USB Unable to detect USB. C o n n e c t i o n F a i l 0 1 memory.
Page 58
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. BlockErase failed before rewriting If the FL display stops at the Error dis- E r a s e f a i l Main.
Page 59
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. TimeOut in USBCheck. If the FL display stops at the Error dis- C o n n e c t i o n F a i l 3 9 play, press and hold the "Power opera- tion"...
Page 60
Error Details of Error code Display Coping strategies Code This unit automatically retries several Abnormal data in UpdatePacket times. Wait until the FL display stops. received from CX870 (FormatEr- If the FL display stops at the Error dis- U p d a t i n g f a i l ror).
Page 61
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. Mismatched CheckSum in Check- If the FL display stops at the Error dis- U p d a t i n g f a i l Sum comparison after rewriting.
Page 62
1.11. Device display during firmware update Display of target device during firmware update. Target device Display Error code when an error occurs 08 - 0B 10 - 15 Main CPU 20 - 27 M a i n : * * % * * * m i n 36 - 3B 50 - 52 Audio PLD...
2. Updating by DPMS Download the latest firmware from the internet and update the firmware. 2.1. Network Connection (1) System Requirements • A broadband internet connection • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Settings Internet Computer Modem LAN port / Ethernet connector...
Page 64
2.3. About the error code See the following table for details on the error code, details of the error code, display and coping strategies when updating the firmware from DPMS. (DPMS:Denon Product Management Server). Error Details of Error code Display...
Page 65
Error Details of Error code Display Coping strategies Code Main CPU failed to receive firm- Turn on the power again. Update will ware for rewriting sent from U p d a t i n g f a i l start automatically. CX870 (when an error occurred).
Page 66
Error Details of Error code Display Coping strategies Code Check the network connection. Update Connection to DPMS has timed in an environment where there is a C o n n e c t i o n F a i l 3 9 out when rewriting the Main CPU.
Page 67
Error Details of Error code Display Coping strategies Code DSP, PLD etc. failed to receive the Turn on the power again. Update will firmware for rewriting sent from U p d a t i n g f a i l start automatically.
Page 68
Error Details of Error code Display Coping strategies Code Notified that the access to the Check the network connection. Update DPMS is congested line, when in an environment where there is a S e r v e r b u s y A 3 rewriting the CX870 system (Ap- small network load.
Page 69
Device display during firmware update Display of target device during firmware update. Target device Display Error code when an error occurs 08 - 0C 10 - 15 Main M a i n : * * % * * * m i n 22 - 24 36 - 3E 50 - 52...
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DV voltmeter. (2) Place the unit in normal usage conditions, away from highly ventilated areas such as next to an air conditioning ma- chine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. (3) Settings of This Unit •...
SURROUND MODES AND PARAMETERS Contents Connections Playback Settings Tips Appendix Sound modes and channel output SThis indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.”. (v p. 174) Channel output Sound mode (v p.
Page 72
Contents Connections Playback Settings Tips Appendix Surr.Parameter (v p. 145) Audyssey (v p. 151) Neo: 6 Music Pro Logicg/gx Music mode only mode only Restorer Tone Control Sound mode (v p. 114) (v p. 111) 10 (v p. 149) Panorama Dimension Center Width Center...
Page 73
Contents Connections Playback Settings Tips Appendix Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. 2-channel signal Multi-channel signal Analog /PCM Dolby Digital DTS-HD DTS Express DTS Dolby TrueHD Dolby Digital Plus Dolby Digital EX Dolby Digital Sound mode (v p.
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator Does the power indicator on the on the front panel flash in front panel flash in red when the green when the power is power is turned on? turned on?
2. Analog video MONITOR OUT(CVBS) output NG Is the power supply voltage being output correctly? Power circuit is faulty. +5VV :C8812 : + side -5VV :C8813 : - side Is a signal being input to the video Check the pattern from JK881 to Is a signal being output from amplifier? IC881, and check the cable between...
(6) Are the HDMI output settings of the Blu-ray/DVD player correct? ray/DVD player and set the HDMI output correctly. (7) If using a DENON Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES if using a Blu-ray/DVD player from another company.
Page 77
(13) Is HDMI input set on the TV? check the input setting. The TV is faulty. (14) Are a picture and sound output when a different TV is used? Check the unit. See "AVR-X1100W/S700W_HDMI Rx-Tx Failure Detection Procedure Manual ver_1.00" of SDI.
4. AUDIO 4.1. AUDIO CHECK No audio output SURROND DIAGNOSTIC CHECK1 INPUT SOURCE MODE PATH DIAGRAM Check the ANALOG AUDIO BLOCK ANALOG Audio output OK? DIRECT ANALOG fig.7 SURROND DIAGNOSTIC CHECK2 INPUT SOURCE MODE PATH DIAGRAM Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT...
Page 79
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuited? Replace the power transistor. 2SB1560/2SD2390 Is the emitter resistor of the power transistor open? Replace the emitter resistor. 0.47Ω Is the base resistor of the power transistor open? Replace the base resistor.
4.3. Analog audio No audio output. Is a voltage of ±12V supplied to Repair the ±12V power supply. DIGITAL PCB CN823? Is there an audio signal in DIGITAL Repair the power amplifier. PCB CN822? Is electron volume serial data being Check the CPU.
5. Network/Bluetooth/USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn Is the LAN cable correctly inserted? on the power again. Check the connection environment Set the IP address, etc. correctly. If the IP settings are fixed, check that no Are the network settings of this unit correct? other devices have the same IP address and...
Page 82
5.2. Cannot connect to the Bluetooth Can a voltage (5V) be confirmed between pin 1 and pin 4 of CN471 The circuit between the AC inlet and BN601 is faulty. on DIGITAL PCB? Check the SMPS PCB. The circuit between CN741 of the DIGITAL PCB and Can a voltage (3.6V) be confirmed to BN921 on Bluetooth PCB? BN921 of the Bluetooth PCB are faulty of wire or board.
Page 83
5.3. A connected USB device is not recognized. Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16 and FAT32-formatted mass storage class, MTP- Is the USB device supported by this unit? compatible devices and iPods (with the exception of some models).
6. SMPS DC 5V is not output. Replace the IC601 (TOP258MG) and Is IC601 (TOP258MG) damaged? D6001 - D6004. Has a fuse (F6001) broken? Is there the damage in D6001 - D6004? Replace the damaged part. Are there any short circuits caused by Repair the short circuited area(s) by the the soldering of the PCB? soldering of the PCB.
Page 85
Operation waveform for each part SMPS Primary drain After primary side rectification (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) D6013 OPTION RBQ30T65A C6002 0.01uF 250V OPTION D6001 1N4007 After secondary rectifications D6002 1N4007 D6011 OPEN D6003 1N4007 D6004 1N4007 LF602 E3,JP:LF-4ZB-E273H...
BLOCK DIAGRAM VIDEO HDMI OPTICAL ANALOG AVR-S700W/X1100W GND DIAGRAM IN/OUT INPUT/OUT ETHERNET COAXIAL ZONE2 OUT PRE OUT INPUT TUNER AC CORD SPEAKER OUT HDMI 2.0 MN864778 DIR/ADC MN864778A PCM9211 OPEN HDMI TRANSCEIVER ADV7623 PCM5100 TRANS NETWORK PCM1690 CY920 OPEN PRE GND OPEN AGND(MIC) DGND...
50mA TUNER+5V A-12V KIA7912PI VOLUME IC MAIN TRANS (NJU72340A) MM1Z7V5 ZONE VOLUME IC 34mA (BD3812F) MM1Z6V8 ZONE VOLUME IC (BD3812F) MM1Z6V8 AVR-X1100W E3 ONLY V+5V 22mA (NJM2595) MM1Z5V1 V-5V (NJM2595) MM1Z5V1 RELAY 68mA AC CORD S3(FL+Vdisp) Vdisp(+37V) 163mA FILAMENT AC...
L7530 * AVR-S700W/X1100W VERSION OPTION CB03YTYH600 REMOTE IN VER. R7581(PU) R7582(PD) X1100 E3 OPEN X1100 E1 OPEN AVR-X1100W E3 ONLY X1100 E1C X1010 E1C X1010 JP SCHEMATIC DIAGRAMS (5/19) S700W E3 SCH05_MCU GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO...
MCU_LEVEL_CHG PART TEMP DETECT & POSISTOR NOT USE : OPTION1,OPTION2,OPTION3 NOT USE & MCU 62PIN,65PIN SET OUTPUT PORT TEMP DETECT USE : OPTION1,OPTION3 POSISTOR USE : OPTION2,OPTION3 (BUT R7633 NOT USE) OPTION1 TO H/S TEMP DETECT PART 2.0mm 3PIN WAFER CN762 CN761 CN764...
DIR/PLD PART TO B0 TO 8C MN864778_HAINT MN864778_HAINT HDMI2_I2S0 TO B9 HDMI2_I2S1 HDMI2_I2S2 RXI2S0 HDMI2_I2S3 RXI2S1 IC774, IC775 CONTROL HDMI2_FS HDMI2_64FS L : A OUT(MN864778A_I2S) HDMI2_MCK H : B OUT(MN864778_I2S) TX64FS TX64FS TXFS TXFS TXI2S0 TXI2S0 C7726 0.1uF TO A4 RXI2S3 TO C4 HDMI1_I2S0...
AVR-S500BT/X510BT/S700W/X1100W FRONT PART BN12B1 TO CN751 BN12B1 FL101 AVR-X1100W E3 ONLY CJP27GB286ZN CFL18BT021GINK RC101 F1001 T 100mA L 250V (37.9kHz) Q1001 D1001 R1061 1N4007ST AVR-S500BT/X510BT KTC1027YT VOUT GND Q1007 OPEN R1060 R1022 OPEN C1012 OPEN R1023 OPEN R1059 C1013 100P...
T 1.25A L 250V 932 TYPE BK301 CHASSIS 1A569 Q3001 1.MCU_3V3 RT1P141C 2.B/P_IRIN_DE JK301 CJJ2D008Z 3.DGND BN302 TO CN754 AVR-X1100W E3 ONLY SCHEMATIC DIAGRAMS (18/19) SCH18_REGULATOR GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL ANALOG VIDEO STBY POWER...
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's ADV7623 (DIGITAL_HDMI_ADV7623 : IC721) DDCC_SCL DDCA_SDA CVDD PIN 1 RTERM CGND 5V_DETA RXC_C–...
Page 123
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 124
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 125
Pin No. Mnemonic Type Description PGND Ground PVDD Ground. PVDD Power PLL Supply Voltage (1.8 V). XTAL Miscellaneous Input pin for 28.63636 MHz crystal or an external 1.8 V 28.63636 MHz clock oscillator source to analog clock the ADV7623. XTAL1 Miscellaneous Crystal Output Pin.
Page 126
ADV7623 Block diagram XTAL XTAL1 VIDEO DATA RXA_C RXB_C RXC_C AUDIO DATA VIDEO DATA RXD_C RXA_0 EQUALIZER SAMPLER RXA_1 RXA_2 AUDIO DATA VIDEO DATA RXB_0 VIDEO DATA SAMPLER RXB_1 EQUALIZER RXB_2 AUDIO DATA RXC_0 AUDIO DATA EQUALIZER SAMPLER RXC_1 RXC_2 RXD_0 RXD_1 EQUALIZER...
Page 127
DIGITAL_HDMI_ADV7623 : IC722 MX25L3206EM2I-12G (except : E2) MX25L6406EM2I-12G (ONLY E2) PIN DESCRIPTION SYMBOL DESCRIPTION SO/SIO1 HOLD# Chip Select Serial Data Input (for 1 x I/O)/ Serial Data SCLK SI/SIO0 Input & Output (for Dual Output mode) SI/SIO0 Serial Data Output (for 1 x I/O)/ Serial Data SO/SIO1 Output (for Dual Output mode) SCLK...
Page 128
Part Number Package Markings Temp Rating (° C) Package Description EN5339QI EN5339 -40 to +85 24-pin (4mm x 6mm x 1.1mm) QFN T&R EN5339QI-E EN5339 QFN Evaluation Board Packing and Marking Information: http://www.enpirion.com/resource-center-packing-and-marking-information.htm EN5339QI (DIGITAL_DIGITAL SUPPLY : IC741~146) Figure 3: Pin Out Diagram (Top View) NOTE A: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage.
Page 130
Pin Name Symbol Pu/Pd STBY STOP Function STBY P32/IRQ2-A/PO10/ MN864778A MN864778A HDMI INT input TIOCC0/TCLKA-A HINT P31/IRQ1-A/PO9/ ADV7623 INT1 ADV7623 INT1 output TIOCA0/TIOCB0 P30/IRQ0-A/PO8/ RC IN RemoteControl Signal input TIOCA0 P27/PO7/TIOCA5/ Hi-B RL HIGH B RELAY Control TIOCB5/SCK1 P26/PO6/TIOCA5/ PSCL MN864778/778A Control TMO1/TxD1 3VPu...
Page 131
Pin Name Symbol Pu/Pd STBY STOP Function STBY P76/IRQ14-A TU GPO2_INT TUNER Control ZVOL MUTE(NA)/ ZONE VOL(BD3812) Control NC(AP/CH) PC7/A23/CS4#-D/ DSP MOSI DA3VPu DSP communication (transmission) CS7#-D/TxD5 PC6/A22/CS6#-D/ DSP MISO DA3VPu DSP communication (reception) RxD5 PC5/A21/CS5#-D/ DSPI CLK DA3VPu DSP communication (CLK) SCK5 PC4/A20 DSP RST...
Page 132
Pin Name Symbol Pu/Pd STBY STOP Function STBY MN864778A PE7/IRQ7-A/D15 MN864778A HDMI Audio INT input HAINT PE6/IRQ6-A/D14 MN864778 HINT MN864778 HDMI INT input MN864778 PE5/IRQ5-A/D13 MN864778 HDMI Audio INT input HAINT Input Selector Rotation detection input PE4/D12 ISEL A (ENCODOR)※ Operate as VSEL B Input Selector Rotation detection input PE3/D11 ISEL B...
Page 133
MC14094B MC14094BDTR2G (DIGITAL_MCU : IC753-754) MC14094B PIN ASSIGNMENT 3−STATE TEST CIRCUIT STROBE FOR t AND t FOR t AND t OUTPUT DATA ENABLE CLOCK R1 = 1 k = t R1 = 10 k = t O.E. DATA OUTPUT 50 pF Q′...
Page 134
R1EX24128BSASOI (DIGITAL_MCU : IC752) Internal Package Shipping Orderable Part numbers organization tape and reel Halogen free Inner wire Block diagram Pin Function Descriptions SN74LVC244APWR (DIGITAL_MCU LEVEL CHG : IC761) SN74LVC244A OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS www.ti.com SCAS414X – NOVEMBER 1992 – REVISED MARCH 2005 Block diagram LOGIC DIAGRAM (POSITIVE LOGIC) Pin numbers shown are for the DB, DGV, DW, N, NS, PW, and RGY packages.
Page 141
PCM1690DCAR (DIGITAL_MAIN DAC : IC791) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 —...
Page 142
BD82065FVJ-E2 (DIGITAL_NETWORK : IC801) BD82061FVJ BD82065FVJ Block diagram SN74LVC827APWR (DIGITAL_NETWORK : IC804) SN74LVC827A 10-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS www.ti.com TSZ02201-0E3E0H300350-1-1 SCAS306J – MARCH 1993 – REVISED FEBRUARY 2005 Block diagram 2013.03.11 Rev.001 FUNCTION TABLE INPUTS OUTPUT LOGIC DIAGRAM (POSITIVE LOGIC) To Nine Other Channels TSZ02201-0E3E0H300350-1-1 2013.03.11 Rev.001...
Page 143
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION PCM5100PWR (DIGITAL_NETWORK : IC805) TERMINAL FUNCTIONS, PCM510x PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM...
Page 146
NJM2595 BD3812F BD3812F (DIGITAL_ANALOG : IC851) Application circuit 5-INPUT 3-OUTPUT VIDEO SWITCH 10µ OUT1 I GENERAL DESCRIPTION I PACKAGE OUTLINE The NJM2595 is a 5-input 3-output video switch. Its switches OUT2 select one from five signals received from VTR,TV,DVD, AGND TV-GAME and others.
Page 147
Input Voltage CONTROL (C) Lead Bend DRAIN (D) INTERNAL SUPPLY Outward from Drawing SHUNT REGULATOR/ ERROR AMPLIFIER (Refer to eSIP-7F Package SOFT START 5.8 V 4.8 V Outline Drawing) 5.8 V INTERNAL UV PS(UPPER) TOP258MG (SMPS : IC601) COMPARATOR V I (LIMIT) CURRENT M Package LIMIT...
Page 150
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 151
FRONT REF No. Part No. Part Name Remarks Q'ty New C1019 CAP,ELECT(50V/10uF) CCEA1HH100T C1020 CAP,CHIP(1608,50V/0.01uF,X7R)_SAMSUNG CCUS1H103KCS C1038 CAP,ELECT(16V/47uF)-S CCEA1CKS470T C1039 CAP,CHIP(1608,50V/100pF,C0G)_SAMSUNG CCUS1H101JAS C1050 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C1052 CAP,ELECT(10V/220uF)-S CCEA1AKS221T C1053-1055 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C1065 CAP,ELECT(50V/1uF) CCEA1HH1R0T C1066 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C1067 CAP,ELECT(50V/1uF) CCEA1HH1R0T C1068 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS...
Page 152
MAIN MAIN PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 153
MAIN REF No. Part No. Part Name Remarks Q'ty New R5417,5418 RES,M-OXIDEFILM(1W/4.7ohm) CRG1SANJ4R7RT R5419-5422 943124500050S RES,M-OXIDEFILM(2W/0.47ohm) CRG2SANJR47RT R5423 RES,CARBON(1/5W,820Kohm,J) CRD20TJ824T R5424 RES,CARBON(1/5W,180Kohm,J) CRD20TJ184T R5425 RES,CARBON(1/5W,10Kohm,J) CRD20TJ103T ! R5426 252310006506S PTCTHEMISTORS,CHIP(115'C) CRTPRF18BB471QB R5427 RES,CARBON(1/5W,5.6Kohm,J) CRD20TJ562T R5429 RES,CARBON(1/5W,15Kohm,J) CRD20TJ153T R5430,5431 RES,CARBON(1/5W,22Kohm,J) CRD20TJ223T R5432 RES,M-OXIDEFILM(1W/10ohm) CRG1SANJ100RT...
Page 154
MAIN REF No. Part No. Part Name Remarks Q'ty New C5508 13405014940AS CAP,ELECT(63V/100uF) CCEA1JH101T C5509 CAP,MYLAR(50V/0.1uF/J) HCQI1H104JZT C5510 CAP,MYLAR(50V/0.047uF/J) HCQI1H473JZT C5511 CAP,MYLAR(50V/0.018pF/J) HCQI1H183JZT C5513 CAP,MYLAR(50V/1500pF/J) HCQI1H152JZT C5607 943134500070S CAP,ELECT(100V/10uF) CCEA2AH100T C5608 13405014940AS CAP,ELECT(63V/100uF) CCEA1JH101T C5609 CAP,MYLAR(50V/0.1uF/J) HCQI1H104JZT C5610 CAP,MYLAR(50V/0.047uF/J) HCQI1H473JZT C5611 CAP,MYLAR(50V/0.018pF/J) HCQI1H183JZT...
Page 155
POWER POWER PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 156
POWER REF No. Part No. Part Name Remarks Q'ty New ! F6001 963652010500S FUSE(S506Series,250V,1.6A) E2/E1/E1C CBA2C1600TLEC ! F6002 90M-FS001430R FUSE(218Series,250V/6.3A) E3/K KBA2C6300TLEY ! F6002 90M-FS001420R FUSE(218Series,250V/3.15A) E2/E1/E1C KBA2C3150TLEY...
Page 158
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R7101 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R7102 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7103-7105 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R7106-7108 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R7111 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R7112 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7113-7115 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R7116-7118 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R7121 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R7122 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7123-7125 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T...
Page 159
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R7453,7454 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R7455 RES,CHIP(1608/1%/348Kohm) CRJ10DF3483T R7456 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T R7457 RES,CHIP(1608/1%/174Kohm) CRJ10DF1743T R7463-7477 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7478 RES,CHIP(1005/5%/3.3Kohm) CRJ06IJ332T R7479,7480 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7481 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R7482 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R7483 RES,CHIP(1005/5%/100Kohm) CRJ06IJ104T R7484 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T...
Page 160
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R7771-7781 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7801 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7802-7804 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R7805 RES,CHIP(1608/5%/1Mohm) CRJ10DJ105T R7806 RES,CHIP(1608/5%/390ohm) CRJ10DJ391T R7807-7810 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7811,7812 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7813 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R7815,7816 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7817 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7818 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T...
Page 161
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R8026-8028 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R8041 RES,CHIP(1005/5%/10ohm) CRJ06IJ100T R8055 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R8057 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R8058 RES,CHIP(1608/5%/10Kohm) CRJ10DJ103T R8060 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R8061,8062 RES,CHIP(1005/5%/470ohm) CRJ06IJ471T R8063,8064 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T R8074 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R8076 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R8077 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T...
Page 162
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C7139 CAP,CHIP(1608,50V/12pF,C0G)_SAMSUNG CCUS1H120JAS C7140-7142 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7143,7144 CAP,CHIP(1005,50V/1000pF,X7R)_SAMSUNG CCUI1H102KCS C7145,7146 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7147,7148 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS C7153,7154 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS C7157,7158 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS C7163,7164 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS C7166,7167 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS C7169,7170 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS C7180,7181 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS...
Page 163
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C7460 CAP,CHIP(2012,6.3V/22uF,X5R)_SAMSUNG CCUC0J226KCS C7461 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C7464 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7465 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C7466 CAP,CHIP(2012,6.3V/22uF,X5R)_SAMSUNG CCUC0J226KCS C7467 CAP,CHIP(1608,50V/5pF,C0G)_SAMSUNG CCUS1H050CAS C7468 CAP,CHIP(1608,10V/1uF,X7R,X7S)_SAMSUNG CCUS1A105KCS C7469 CAP,CHIP(2012,6.3V/22uF,X5R)_SAMSUNG CCUC0J226KCS C7470 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C7471 CAP,CHIP(2012,6.3V/22uF,X5R)_SAMSUNG CCUC0J226KCS C7472 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS...
Page 164
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C8060 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C8061 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C8062 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C8063,8064 CAP,CHIP(1608,50V/2200pF,X7R)_SAMSUNG CCUS1H222KCS C8101-8105 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C8108-8111 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C8112 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C8113-8121 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C8122 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C8127 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C8128 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS...
Page 165
DIGITAL REF No. Part No. Part Name Remarks Q'ty New L7528-7530 FERRITECHIPBEAD(1608/60R,CB03YTYH600) X1100E3 CLZ9R005V L7601-7617 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L8001-8004 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L8007,8008 COMMONMODEFILTER(2012,90ohm) CLZ9Z174Z L8009,8010 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L8101,8102 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T L8201,8202 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V X7101 943141100720S X-TAL,SMD3.2X2.5,27.000MHz,10PF COX27000I100ST X7201 943141100600S X-TAL,SMD3.2X2.5,28.636MHz,12PF COX28636I120ST X7301 943141100720S X-TAL,SMD3.2X2.5,27.000MHz,10PF...
Page 166
KDIFF-AMP KDIFF-AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 168
ADAPTER ADAPTER PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 171
PACKING PACKING ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Need help?
Do you have a question about the AVR-X1100W and is the answer not in the manual?
Questions and answers