COLOR MONITOR SyncMaster 570sTFT (CN15LS*) SyncMaster 580sTFT (CN15LO*) SERVICE Manual COLOR MONITOR CONTENTS 1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Troubleshooting AUTO AUTO EXIT EXIT MENU MENU 5. Exploded View & Parts List SyncMaster 570sTFT 6. Electrical Parts List 7.
Page 2
Samsung Electronics Co., Ltd. May 2000. Printed in Korea P/N. : BN68-00097C-01...
1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the (READING SHOULD circuit board. NOT BE ABOVE 0.5mA) Disconnect the AC power and DC Power Jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
2 Product Specifications 2-2 Pin Assignments Sync 15-Pin Signal Cable Connector Type Separate Composite Sync-on-green Pin No. Green + H/V Sync Green Green Blue Blue Blue GND (DDC Return) GND (DDC Return) GND (DDC Return) GND-R GND-R GND-R GND-G GND-G GND-G GND-B GND-B...
2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode VESA VGA1/70 Hz VGA3/60 Hz VGA2/70 Hz 640/72 Hz 800/60 Hz 640/75 Hz 800/56 Hz...
Page 8
2 Product Specifications Table 2-1. Timing Chart Continued Mode VESA MAC. 640/67 Hz 832/75 Hz 1024/60Hz 1024/70Hz 1024/75Hz 800/72 Hz 800/75 Hz 1024x768 1024x768 1024x768 60 x 480 832 x 624 800 x 600 800 x 600 Timing fH (kHz) 35.000 49.726 48.077...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the Sync Master 570s TFT / 580s TFT monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1.
Page 10
3 Disassembly and Reassembly 4. Remove the Stand Rear from the Stand 3-1-6 Wire frame stand Disassembly (option) assembly. 1. Carefully pull the cover hinge. 5. Remove the Stand Front from the Stand 2. Remove the cover vesa from the Stand assembly.
Page 11
3 Disassembly and Reassembly 4. Dis-assembled the lamp ass’y from LCD completely. 3-3 Replacement Order of Lamp Assemblies (CN15LSS/CN15LOS : Samsung Panel) 1. After confirm there is nothing on the disk Turn the LCD module over and put it on a flat desk set to the ground.
Page 12
3 Disassembly and Reassembly 3. Please take out the lamp unit from the LCD module. 4. Please fix the new lamp units on the LCD module : opposite process 2 and 3 Replacement of lamp unit should be done at the power off state and recommanded clean bench condition.
4 Troubleshooting Notes: 1. Before troubleshooting, setup the PC’s display as below. • Resolution: 1024 x 768 • H-frequency: 48 kHz • V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. •...
Page 15
4 Troubleshooting 4-2-A No Video (CN15LSS/LOS) Power indicator is green Does the clock pulse Does the H-sync pulse appear Does the pulse appear at Pin 9 appear at Pin 84 of at Pin 94 of IC133? of IC182 or Pin 1 of IC181? IC133? Replace IC182.
Page 16
4 Troubleshooting 4-2-B No Video (CN15LSB/LOB) Power indicator is green Does the clock pulse Does the pulse appear at Pin 9 Does the H-sync pulse appear appear at Pin 84 of of IC182 or Pin 1 of IC181? at Pin 94 of IC133? IC13? Replace IC182.
Page 18
4 Troubleshooting 4-3 No Video of Alternate Vertical Line (CN15LSS/LOS) (CN15LSB/LOB) One or more even or odd vertical lines do not display. WAVEFORMS Does the waveform appear Replace IC251 and IC252 at Pin 10 or Pin 2 of CN201? or check its related circuit. cn201 #20 Replace LCD panel.
Page 19
4 Troubleshooting 4-5 User Controls Don’t Work (CN15LSS/LOS) (CN15LSB/LOB) Does the DC level change at Check the buttons. Pins 35 and 36 of IC311 when you (SW801~SW808) push the front panel button? Go to 4-4 No OSD Display. 4-6 No Sound (CN 15LSS/LOS) (CN15LSB/LOB) Does the DC 12V appear at Pin Check IC801, VR803 and related 2 of IC801, Pin 6 of CN801?
Page 20
4 Troubleshooting 4-7 Microphones Don’t Work Does the PC’s sound Check the PC’s sound program program operate well? and compatibility. Is the connection between the PC Connect the cable between the PC and monitor secure? and monitor. Check the connection between Is the Internal Microphone CN808 on the Audio PCB and the connector attached?
Page 21
5 Exploded View and Parts List 5-1 Simple Base (CN15LSS) SyncMaster 570sTFT/580s TFT...