DTX Vortex Owner's Manual
  1. Manuals
  2. Brands
  3. DTX Manuals
  4. Kitchen Appliances
  5. Vortex
  6. Owner's manual

DTX Vortex Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

TM
Vortex Cotton Candy Machine
Owner's Manual
Copyright 2012 DTX International All Rights Reserved

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vortex and is the answer not in the manual?

Questions and answers

Related Manuals for DTX Vortex

Summary of Contents for DTX Vortex

  • Page 1 Vortex Cotton Candy Machine Owner’s Manual Copyright 2012 DTX International All Rights Reserved...

  • Page 2: Important Safety Precautions

    • DO NOT immerse any part of your • ensure that your Vortex machine is machine in water. Immersion may result in properly grounded to avoid potential damage to the machine. Use minimal electric shock.
  • Page 3 16. Clean daily. Do not use detergent to clean, clean with water and a soft cloth. 17. NOTE: If your spinning head becomes jammed, switch Power to OFF, unplug, remove head and clean off sugar and reassemble. SAVE THESE INSTRUCTIONS Copyright 2012 DTX International All Rights Reserved...

  • Page 4: Grounding Instructions

    Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges. Copyright 2012 DTX International All Rights Reserved...

  • Page 5: Electrical Specifications

    • Our commercial, heavy-duty motor WARRANTY • The Vortex Cotton Candy machine carries the Great Northern Popcorn Company’s limited 1 year warranty. Motor bearings and the floss kettle/pan are excluded. Copyright 2012 DTX International All Rights Reserved...

  • Page 6: Components & Specifications

    CHILDREN AND UNAUTHORIZED OR UNTRAINED PERSONS AWAY DURING OPERATION! SPECIFICATIONS Yield Frequency Motor Power Voltage Heating Power Dimensions Machine Only: 20.5” x 20.5” x 19.7” 1/30sec 110V 60Hz 950W Machine with Cart: 28.3” x 28.3” x 19.7” Copyright 2012 DTX International All Rights Reserved...

  • Page 7: Assembly Procedures

    If the plug or cord are damaged, DO NOT Figure F ATTEMPT TO START MACHINE. Instead, Figure E call support or contact us online (See page 5 for contact details). Figure I Figure G Figure H Copyright 2012 DTX International All Rights Reserved...

  • Page 8: Operating Procedures

    Figure K. Finally, hook the metal rings of the clamps over the lips of the brackets and close the clamps into place securely. Repeat for the other side of the machine, securely fastening all four clamps and brackets. Copyright 2012 DTX International All Rights Reserved...
  • Page 9 5. To clean the floss head, TURN MACHINE OFF, UNPLUG AND ALLOW TO COOL COMPLETELY, THEN WIPE WITH A CLEAN MOISTENED WARM SOFT CLOTH. CLEAN MACHINE AFTER EVERY USE. Figure Q Copyright 2012 DTX International All Rights Reserved...

  • Page 10: Important Precautions

    CAUTION! Spinning floss head is HOT! Do not touch head immediately after use! NOT TOUCH PLUG WITH WET HANDS! ALWAYS wear protective eyewear USE ONLY COTTON CANDY FLOSS CONES TO COLLECT SUGAR FLOSS. Copyright 2012 DTX International All Rights Reserved...
  • Page 11 USE. TURN MACHINE OFF, UNPLUG AND ALLOW TO COOL COMPLETELY, THEN WIPE WITH A CLEAN MOISTENED WARM SOFT CLOTH. AVOID USING EXCESSIVE AMOUNTS OF WATER WHEN CLEANING AND ENSURE THAT THE MACHINE IS THOROUGHLY DRY BEFORE USE. Copyright 2012 DTX International All Rights Reserved...
  • Page 12 Parts List - Cart Major Components Parts List - Nuts & Bolts Bag Copyright 2012 DTX International All Rights Reserved...

  • Page 13: Cart Assembly

    4) Ensure the cart frame sits level when placed upside down on the floor or other flat surface, and that the two grooves in the axle posts are facing sideways to the assembly, as shown in F igure T Figure T Copyright 2012 DTX International All Rights Reserved...
  • Page 14 When finished your cart frame and wheels should look like Figure Y. Ensure the cart sits flat on the floor or table top before proceeding. You are now ready to mount the frame onto the cotton candy machine. Copyright 2012 DTX International All Rights Reserved...
  • Page 15 7mm nuts ( ). Repeat until all four small bolts and nuts are fastened securely (see Figure BB Repeat step 12 with Shelf ( ) on the opposite side of the machine (the side opposite the wheels). Figure BB Copyright 2012 DTX International All Rights Reserved...
  • Page 16 Congratulations! Your Great Northern Cotton Candy Cart is now finished. You may now reinstall your gray cover and return to Page 8 to complete your setup and begin making the best cotton candy you ever tasted! Copyright 2012 DTX International All Rights Reserved...

Table of Contents