Page 1
00571A-SCC-C6403P-ENG 8/17/06 1:52 PM Page 1 SmartDome Camera SCC-C6403P Owner’s Instructions Benutzerhandbuch Manuel d’instruction Manual del usuario Istruzioni per l’uso Part : AB68-00571A(00)
00571A-SCC-C6403P-ENG 8/17/06 1:52 PM Page 3 Important Safety Instructions Safety Precautions 1. Read these instructions. The purpose of this information is to ensure proper use of this product to 2. Keep these instructions. prevent danger or damage to property. Please be sure to observe all 3.
Never disassemble or modify this product in Note: This equipment has been tested and found to comply with the limits for any way. (SAMSUNG is not liable for problems caused by unauthorized a Class A digital device, pursuant to part 15 of the FCC Rules. These modifications or attempted repair.)
Page 1-1 Table of contents Before Usage Before Usage .......................1-1 This is a basic instruction manual for the SCC-C6403P user. It contains all the instructions needed to use the SCC-C6403P Chapter 1 SCC-C6403P Overview ................1-4 from a simple introduction of the control locations and functions of SCC-C6403P Introduction ................1-5...
- ZONE ID SET ...................3-21 - ZONE ENABLE.................3-21 5. AUTO SET....................3-22 - AUTO PAN ..................3-22 In this chapter we will briefly introduce the SCC-C6403P - POSITION SET.................3-22 - SPEED....................3-23 and show main functions, locations of control and Switch - DWELL TIME..................3-23 Setting.
SCC-C6403P Introduction Locations of Control FRONT SCC-C6403P is a zoom lens built in smart dome camera which provides you with the best monitoring function in connection with CCTV at banks or companies. The SCC-C6403P is a high quality surveillance camera using x32 zoom lens and digital zoom IC, it can catch clear images up to 320 times.
SW701 SW702 SW703 lowest. Setting communication Protocol Use number 1~4 PIN of SW704 to set communication Protocol. Division n < 32 A : SAMSUNG HALF PIN1 PIN2 PIN3 PIN4 Comp B : SAMSUNG FULL Termination SW1-ON...
Chapter 2 SCC-C6403P Installation package: In this chapter, we will check the contents of the package before installing the SCC-C6403P, and prepare a power adapter suitable for the power supply system. (Power Consumption: 18W; Voltage: AC24V, 1.5A) Then, we will install the SCC-C6403P and connect the cables.
Video Output Terminal Power Adapter Cable (VIDEO OUT) The cable that plugs into the SCC-C6403P power input receptacle has the 2. Then, connect the other end of rated voltage of AC24V, 1.5A. the connector to the Video Input Check the rated voltage before using the cable.
1) Make sure that the installation site can sufficiently support a minimum of This housing is used for installing the SmartDome Camera to an indoor four times the net weight of the SCC-C6403P SmartDome Camera and wall or a ceiling.
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 2-7 Installing the Camera 1. [Figure 1] Install the structure on the ceiling. (Refer to Installation reference 5) CEILING MOUNT ADAPTOR (SADT-100CM) for the Length of the structure) This adaptor is used for installing the indoor housing or the outdoor * Built in by the builder of the structure housing for the SmartDome Camera to a concrete ceiling.
[Figure 5] [Figure 6] In this chapter, we will look over the Setup Menu of the SCC-C6403P, First we'll look over the overall structure of the Setup Menu, and then we'll look at the functions of each menu. [Figure 7] 7.
In this section, a description of the Setup menu features will enable users of the ZONE SET ZONE DIR SET OFF/ON... ZONE AREA SET OFF/ON... SCC-C6403P to tailor it to their personal needs. EXIT QUIT/SAVE AUTO SET AUTO PAN 1.../2.../3.../4...
QUIT CAMERA ID to ON and press [Enter]. You will see the sub screen for deciding on the ID of the SCC-C6403P. The Camera ID can have up to 20 alphanumeric characters, along with several special characters. The assigned camera ID may be positioned to any desired location on the...
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-6 COLOR/BW In AUTO mode, AGC will be displayed as “---“. You can’t adjust the settings manually. In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter. In a poor illumination environment, the IR filter is turned off in the BW mode the its sensitivity increases as high as a black and white camera.
The magnification ratio ranges from OFF to 10. If you set Digital RIGHT..., CENTER... or USER... as AREA where the Motion Detection Zoom of SCC-C6403P to max. 10 times, the mode will become the 32 time function is applied.Select one from TOP..., BOTTOM..., LEFT..., RIGHT..., optical zoom and you will be able to enlarge a subject by max.
The EXIT menu is used to quit the CAMERA SET menu of the the [Left, Right] key. For SIZE items, you can use the [Up, Down, Left, SCC-C6403P and return to the MAIN MENU. - QUIT : Ignores the changed information and restores the saved Right] key to designate the SIZE, and then press the [ENTER] key.
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-12 SHUTTER You may designate both the fast electronic shutter speed and low The AGC menu was designed to provide you with brighter screen electronic shutter speed in the SHUTTER menu. The fast electronic supposed you photographed any subject in the dark resulting in less shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to brighter image than regulated.
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-14 You can select one of four modes for white balance adjustment as follows: WHITE BAL Lights are generally denoted as color temperatures and expressed in - ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the Kelvin (K) units.
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-16 EXIT FOCUS MODE It's the same as the EXIT function of the CAMERA SET menu. In the FOCUS MODE MENU, the Focus method can be set to ONEAF (One Auto Focus), or MF(Manual Focus).
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-18 POSITION SET 4. ZONE SET From "POSITION SET..." press [ENTER] to get into the PAN/TILT, FOCUS/ZOOM SET screen The ZONE SET menu includes the setup of ZONE DIRECTION, and to set the PAN/TILT location and FOCUS/ZOOM condition then press ZONE AREA.
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-20 ZONE AREA LOCATION The “LOCATION...” menu designates the left/right LIMIT positions of Press [ENTER] to enter the ZONE AREA MAP screen from “ZONE ZONE AREA. Enter the setup screen to move PAN, then select a start AREA SET...”.
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-22 5. AUTO SET SPEED This is a setting function for movement speed setup. It can be set from The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is STEP1 to STEP64.
This function sets up the motion which will be repeatedly performed by set up before the 2-minutes ends, press [ENTER]. SCC-C6403P whenever the time set by AUTO RETURN elapses. It covers SCAN, AUTO PAN, PATTERN, and PRESET setup. PLAY NUMBER SCAN This menu allocates a number to the motion set by AUTO PLAY.
00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 3-26 AUTO SET 6. ALARM SET This menu designates what to do at the time of ALARM input. Once an alarm is given, the camera will shortly move to the PRESET position It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an corresponding to the respective alarm as follows.
AUTO CAL [Enter] PASSWORD ON... This function turns on or off Auto Calibration. SCC-C6403P has the Auto EXIT QUIT Calibration function to improve the precision of LENS and PAN/TILT motor. You may set to OFF/6H/12H/18H/24H. Without user’s key input for Press UP/DOWN/LEFT/RIGHT key to locate the cursor on a number and the time designated by the user, A.C will appear on the screen while...
8/17/06 1:53 PM Page 3-30 9. SHORT KEYS SSC-1000 or SSC-2000 Controller supports the following short keys. Function SCC-C6403P has two FANs inside for preventing overheating. CAMERA SET… If FAN doesn't work properly, messages below will be displayed. COLOR/BW COLOR [PRESET] + [1] + [2] + [8] + [Enter] In those case, replace the FAN.
Remark Product Type Zoom lens single body SmartDome CAMERA • The copyright of the manual belongs to Samsung Electronics Co., Ltd. Power Input AC 24 ± 10% (50Hz ± 0.3Hz) • Without the permission of Samsung Electronics it cannot be reproduced...