Table of Contents
Advertisement
Available languages
Available languages
TROUBLESHOOTING
35
ERROR CODES
_!_i_i_iiii_!_!_!!i!!!!iiiiiiii_i_!_i_!_!_i_i!ii_!_iiiiiii_i_!_!!ii!!_i_!_!_!!_!!_!!_!!_!_!_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_
iThe display shows:
i||
shows:
i
The display shows:
Washer fills with water slowly or
not at all, or the display shows:
The lid is not closed properly.
Washer will not turn on
Lid lock switch error.
Special Drain Feature.
Water supply faucets are not fully
open.
Water line hoses are kinked,
pinched, or crushed.
Water inlet filters are clogged.
Water supply pressure to faucet or
house is too low.
Water supply connected with leak-
limiting hoses.
Power cord is not properly
plugged in.
House fuse is blown, circuit break-
er has tripped, or power outage
has occurred.
Make sure that the lid is closed properly
and press the START/PAUSE button. After
starting
a cycle, it may take a few moments
before the tub begins to turn or spin. The
washer will not spin unless the lid is locked.
If the lid is closed and the lid lock error mes-
sage is displayed, call for service.
Make sure that the lid is closed properly and
sress the START/PAUSE button. The washer
will not operate unless the lid is locked.
Make sure that nothing is caught under the
lid, including shipping material or clothing.
Make sure that the latch mechanism
is fully
retracted.
If the lid is closed and the lid lock error mes-
sage is displayed, call for service.
If the washer is paused during a cycle for
more than five minutes, the cycle will be
cancelled and any water remaining in the tub
wiUI be drained.
Make sure that the water faucets are fully
open.
Make sure that the hoses are not kinked or
3inched. Be careful when moving the washer
during cleaning and maintenance.
Clean the inlet fluters. See Maintenance
in
the Care and Cleaning section.
Check another faucet in the house to make
sure that household
water pressure is ad-
equate and flow is not restricted.
Disconnect
the inlet hose from the washer and run a few
gallons of water through the hose to flush
the water supply lines. If flow is too low,
contact a plumber to have the water lines
repaired.
Hoses designed to limit leaks can trip falsely
and prevent the washer from filling. The use
of leak limiting hoses is not recommended.
Make sure that the plug is plugged seruely
into a grounderd, 3-prong. 120-VAC, 60-Hz.
outlet.
Reset circuit breaker or replace fuse. Do not
increase fuse capacity. If the problem is a
circuit overload, have it corrected by a quali-
fied electrician.
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the WT5680HVA and is the answer not in the manual?
Questions and answers
Washer will not fill. Hoses and inlet filters are ok.
The LG WT5680HVA washer may not be filling despite the hoses and inlet filters being okay due to the following reasons:
1. Insufficient Water Supply – Ensure that both hot and cold water faucets are turned on fully.
2. Lid is Open – The washer will not operate if the lid is open. Close the lid completely, ensuring nothing is obstructing it.
3. Reversed Inlet Hoses – Verify that the hot water supply is connected to the hot inlet valve and the cold water supply to the cold inlet valve.
4. High-Efficiency Washer Design – The water level may appear low since this is a high-efficiency washer, and it does not always cover the clothes.
This answer is automatically generated
My washing machine is leaking from the bottom
Your LG WT5680HVA washing machine may be leaking from the bottom due to the following reasons:
1. Faulty Drain Pump Assembly – This is the most common cause, responsible for 45% of leakage issues. If the pump assembly is damaged or clogged, water may leak from the washer.
2. Oversudsing from Excess Detergent – Using too much or the wrong type of detergent (non-HE) can cause excessive suds, leading to leaks.
3. Incorrect Detergent Dispenser Use – Ensure detergent and additives are placed in the correct dispenser compartments.
4. Damaged or Improperly Installed Water Supply Hoses – Cracks, leaks, or improper installation of the water supply hoses can cause water to leak.
5. High Water Supply Pressure – If the water pressure exceeds 116 psi, a pressure-reducing valve may be required to prevent leaks.
6. Hose Issues – Stretched, pinched, crushed, or kinked water lines can lead to leaks.
Checking these components and making necessary repairs or adjustments should help resolve the issue.
This answer is automatically generated