Pacific energy ULC S628 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Pacific energy Manuals
  4. Indoor Fireplace
  5. ULC S628
  6. Installation and operating instructions manual

Pacific energy ULC S628 Installation And Operating Instructions Manual

Pacific summit insert series - a
Hide thumbs
Table of Contents

Advertisement

Quick Links

IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER
SAVE THESE INSTRUCTIONS
SAFETY NOTICE
If this stove is not properly installed, a house
fi re may result. For your safety, follow the
installation directions. Consult local building
or officials about restrictions and installation
inspection requirements in your area.
TESTED and LISTED
to ULC S628 / UL 1482
Meets the U.S. Environmental Protection
Agency's July 1990 Particulate Emission
Standards
230311-20
Summit
Wood Insert
INSTALLATION
AND OPERATING
INSTRUCTIONS
MODEL: PACIFIC
SUMMIT INSERT
SERIES - A
SINS.BODYC
5055.511

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ULC S628 and is the answer not in the manual?

Questions and answers

Related Manuals for Pacific energy ULC S628

Summary of Contents for Pacific energy ULC S628

  • Page 1 INSTRUCTIONS installation directions. Consult local building or officials about restrictions and installation inspection requirements in your area. TESTED and LISTED to ULC S628 / UL 1482 Meets the U.S. Environmental Protection MODEL: PACIFIC Agency's July 1990 Particulate Emission Standards SUMMIT INSERT...

  • Page 2: Table Of Contents

    Contents Safety ....................3 Clearances ..................3 Masonry or Factory Built Fireplace ............3 Dimensions ..................5 Installation ..................6 Fireplace Specifi cations ................6 Into a Masonry Fireplace ................6 Full Flue Liner - (Required in Canada) ............ 7 Direct Flue Connection ................

  • Page 3: Safety

    Safety Clearances Please read this entire manual before installation Masonry or Factory Built Fireplace and use of this wood burning insert. Failure to follow The minimum required clearances to surrounding combustible these instructions could result in property damage, materials when installed into a masonry or factory built fi replace bodily injury or even death.
  • Page 4 Fireplace hearth requirements: (Measured without the insert) The non-combustible fi replace hearth must be raised 2” above an adjacent combustible fl oor and extend 16” in front and 8” beyond each side of the existing fi replace opening. A non-combustible hearth that extends a minimum 20-1/2” in front of the fi replace opening may be fl ush to an adjacent combustible fl oor.

  • Page 5: Dimensions

    Dimensions OVERSIZED SURROUND DIMENSIONS 52 3/4" 6 5/8” 48 3/4" 9 1/8” 34 1/16" 22 15/16” 32 1/16” 21” 10 7/8” 18” 27 9/16” 25 3/8” 28 7/8” 12 1/4” 23 5/16” 40 7/8” SINS.BODYC 230311-20...

  • Page 6: Installation

    Installation Full Flue Liner Fig. # 2 Your Insert is designed to be installed into a masonry or factory built zero-clearance fi replace. The masonry fi replace must be Rain Cap built according to the requirements of the Standard of Chimneys, Fireplaces, Vents and Solid Fuel Burning appliances, N.F.P.A.

  • Page 7: Full Flue Liner - (Required In Canada)

    Full Flue Liner - (Required in Canada) 5) Push insert into fi replace. Use the rear adjustment legs to level insert. 1) Measure the chimney height from the top of the existing fl ue 6) Attach connector pipe to stove collar. to the fl oor of the hearth.

  • Page 8: Into A Factory Built Fireplace

    Into a Factory Built Fireplace Your Insert may be installed into a factory built fi replace (size permitting) with the following requirements: 1) Inspect your fi replace for damage or other physical defects. The fi replace must be in good working condition. If in doubt about its condition, seek professional advice.

  • Page 9: Surround Assembly And Installation

    Surround Assembly and Installation Fig. # 9 Fig. # 7 1) Lay part A, B and C face down on a fl at, non-marring surface. Fasten together with 1/4" x 1/2" bolts and nuts provided through Part F holes at points “D” (Fig. #8 and #10). 2) Lift the surround assembly to the upright position and make sure the front face is fl at and even at the joints.
  • Page 10 10) Slide the pre-assembled surround behind the ash lip. Ensure 7) Remove wing screws on each side of the Bay top and set that the electric supply cord is located in the slots in the base Bay top aside to prevent damage. (Fig. #12). of the surround.

  • Page 11: Fan Speed Controller Relocation

    Fan Speed Controller Relocation carefully lift up the ash lip and remove from the fi rebox and unscrew the wire support tabs. The fan speed controller is factory installed under the ash lip on SCREWS the right hand side. If required, it can be relocated to the left side Fig.
  • Page 12 7) Route cable from speed control to fan and reattach wire sup- 8) Remove Thermal switch from right hand fan mounting bracket port tabs on the underside of the ash lip. Note wire positions. and relocate to left hand fan mounting bracket. Fig #27&28 (Fig.25 &...

  • Page 13: Operation

    Operation Normal Operation 1) Set air control to desired setting. If smoke pours down across the glass (waterfall effect), this indicates you have shut the Wood Selection control down too soon or you are using too low a setting. As every home’s heating needs vary (i.e.

  • Page 14: More Wood, More Heat

    More Wood, More Heat Blower Seasoned wood has approximately 7500 BTU’s per pound. If you put 10 pounds of wood in your stove for an eight hour burn the wood will be producing 9375 BTU’s per hour. (7500 BTU x The Insert comes equipped with twin variable speed circulating 10 lbs / 8 hrs.

  • Page 15: Creosote

    Chimney Fires Creosote The result of excessive creosote buildup is a chimney fi re. Chimney fi res are dangerous. Chimney inside temperatures can exceed 2000 degrees F. This causes much higher than Formation and Need for Removal normal temperatures in the chimney and on its exterior surfaces thus ignition of nearby or touching combustible material is more When wood is burned slowly, it produces tar and other organic likely during a chimney fi re.

  • Page 16: Maintenance

    Maintenance WARNING: Do not overtighten, tighten screws very care- fully. - Do not clean glass when hot 1. Burn wood only, dry and well seasoned. The denser or heavier - Do not use abrasive cleaners on glass the wood when dry, the greater its heat value. This is why hardwoods are generally preferred.

  • Page 17: Understanding & Operating Your Pacifi C Energy Stove

    (smoke). 5 to 10 minutes more Pacific Energy has and then set the air designed a system that control to the desired solves the problem by position.

  • Page 18: Troubleshooting

    Troubleshooting Problem Cause Cure Excessive Creosote 1) Wood is too wet - Use dry wood Buildup 2) Turning down air control - Do not turn down until: too soon a) there is a good bed of coals b) the wood is charred 3) Draft too low - Improper chimney height and/or diameter - Chimney plugged or restricted, check fl ue...

  • Page 19: Firebrick Installation

    Firebrick Installation Summit Insert Wood Stove This package contains 17 full-size fi rebricks, as well as 7 various cut-size bricks. With the woodstove in the upright position, install fi rebricks as follows: 1) Place the fi rebricks on the bottom of the unit fi rst. Use 7 full-size (D) and 3 cut bricks (C &...

  • Page 20: Replacement Parts

    Replacement Parts (WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION) ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1..Bay Top (c/w Washers and Nuts) ....SINS.50374524 WODC.4147C 2..Casing Top, Back ............. 3502 24..Baffle Pin ............SSER.125001 3..Casing Top, Front ............3502.51 25..Brick Rail Set(2 pcs.
  • Page 21 Fig. # 32 SINS.BODYC 230311-20...
  • Page 22 NOTES: SINS.BODYC 230311-20...

  • Page 23: Label

    ETL# 4001507 MODEL / MODÈLE: PACIFIC SUMMIT INSERT SERIES / SÉRIE: A INSTALL AND USE ONLY IN ACCORDANCE WITH PACIFIC ENERGY’S INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT CODES, RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. INSTALL AND USE ONLY IN MASONRY OR FACTORY BUILT FIREPLACE. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
  • Page 24 PACIFIC ENERGY FIREPLACE PRODUCTS LTD. Technical Support: 1-250-748-1184 www.pacifi cenergy.net 2975 Allenby Rd., Duncan, B.C. V9L 6V8 Printed in Canada...

This manual is also suitable for:

Ul 1482

Table of Contents