Vision Fitness T9200 SIMPLE Troubleshooting Manual
Troubleshooting for 2007 treadmills
Hide thumbs
Also See for T9200 SIMPLE:
- Owner's manual (56 pages) ,
- Assembly manual (3 pages) ,
- Service manual (56 pages)
Advertisement
Table of Contents
TROUBLESHOOTING
T R O U B L E S H O O T I N G F O R 2 0 0 7 T R E A D M I L L S :
(T9200 SIMPLE, T9500 SIMPLE, T9600 SIMPLE, T9250 SIMPLE, T9450 SIMPLE)
(T9200 DELUXE, T9500 DELUXE, T9600 DELUXE, T9250 DELUXE, T9450 DELUXE)
(T9200 PREMIER, T9500 PREMIER, T9600 PREMIER, T9250 PREMIER, T9450 PREMIER)
(T9700S, T9700HRT, T9800S, T9800HRT)
1
TREADMILL.TROUBLESHOOTING.2007.REV1
Date of last revision: 11.06
Advertisement
Table of Contents
Related Manuals for Vision Fitness T9200 SIMPLE
Summary of Contents for Vision Fitness T9200 SIMPLE
-
Page 1: Troubleshooting
T R O U B L E S H O O T I N G F O R 2 0 0 7 T R E A D M I L L S : (T9200 SIMPLE, T9500 SIMPLE, T9600 SIMPLE, T9250 SIMPLE, T9450 SIMPLE) -
Page 2: Table Of Contents
Troubleshooting: Treadmills INDEX 10. Elevation problems 1. Data cables • Elevation does not move when key is pressed • Large data cable • Elevation does not reach minimum or maximum elevation • Small data cable • Elevation jumps to maximum elevation on power up •... -
Page 3: Data Cables
Troubleshooting: Treadmills continued DATA CABLE Small Data Cable Large Data Cable The small data cable carries power (11 volts) from the The large data cable carries the communication between lower board to the upper board. This is the only function the lower board and the upper board. -
Page 4: Error Message Codes
Troubleshooting: Treadmills ERROR MESSAGE CODES If an error occurs during auto-calibration of new console, an override of the error may be necessary. Cycle power, press “STOP”, then, on the speed key numeric press “5”, “9”, then “3”. Incline position is outside the tolerances Elevation stall condition Signal from elevation is lost Speed time out error... - Page 5 Troubleshooting: Treadmills continued E4: Solution 1. Check power to the treadmill, as insufficient voltage to the treadmill can cause this error to reoccur. Check the power socket that the tread is plugged into. Eliminate any extension cords or surge protectors (plug the tread directly into a functional power source).
-
Page 6: Maintenance Messages
Troubleshooting: Treadmills continued MAINTENANCE MESSAGES: The T9700 have maintenance messages programmed into the software. These messages indicate that the treadmill has reached the recommended number of hours of use since the last lubrication (LUBE HRS) or the recommended distance since the last cleaning (CLEAN) or the motor brushes (BRUSH) should be replaced. This is NOT an error message and the treadmill can continue to be used, providing the user arranges for the appropriate service. -
Page 7: Treadmill Trips The Circuit Breaker On Power Up
Troubleshooting: Treadmills continued RUNAWAY BELT Symptom Solution Zero to fast in seconds 1. Replace lower board (Console does not reflect • Lower board has a damaged component or moisture on it increase in speed) 2. Inspect and clean brushes and commutator. Replace worn brushes. 3. -
Page 8: Treadmill Running Belt Surges
Troubleshooting: Treadmills continued TREADMILL RUNNING BELT SURGES Symptom Solution Running belt surges 1. Check the power socket that the tread is plugged into. Eliminate any extension cords or surge protectors (plug the tread directly into a functional power source). Make sure the circuit is not overloaded. Make sure the circuit is NON-GFI. 2. -
Page 9: No Power To The Treadmill
Troubleshooting: Treadmills continued NO POWER TO THE TREADMILL Symptom Solution Power switch does not glow. 1. Check the power socket that the tread is plugged into. Eliminate any extension cords or surge protectors (plug the tread directly into a functional power source). Make sure the circuit is not overloaded. -
Page 10: Elevation Problems
Troubleshooting: Treadmills continued ELEVATION PROBLEMS Symptom Solution Elevation does not move 1. Check data cable connections at the lower and the upper boards when key is pressed 2. Calibrate (See engineering mode guide for specific treadmill) 3. Check that the Up Elevation LED on lower board lights when the Up key is pressed and the Down Elevation LED lights when the Down key is pressed. -
Page 11: Noise Problems
Troubleshooting: Treadmills continued NOISE PROBLEMS (continued) Symptom Solution Squeaking or chirping noise 1. Adjust motor pulley and align with front roller pulley 2. Remove drive belt and check the grooves in the belt for debris. Clean drive belt, under front motor cover motor pulley and front roller pulley. -
Page 12: Deck And Belt Problems
HR with all other electrical devices in area turned off. Ex: TV's, Computer monitors, home security, electric dog fence, and various motors. No Heart-Rate Training 1. Check configurations. function Note: All Vision Fitness Heart-Rate transmitters have an operational life of approximately 2500 hours. Date of last revision: 11.06 TREADMILL.TROUBLESHOOTING.2007.REV1...
Need help?
Do you have a question about the T9200 SIMPLE and is the answer not in the manual?
Questions and answers