Page 1
Built-Under Larder AB170 Installation & User Instructions - Please keep for future reference BUCL6082 Installation & User Instructions – Please keep for future reference – Please read these instructions fully before installing or using Important These instructions contain important information that will help you get the best from your appliance, ensuring safe and correct installation, use and maintenance.
Thermostat setting If your larder is not cold enough Reversing the door Cleaning and Maintenance General Defrosting the refrigerator Replacing the light bulb Trouble Shooting Technical Specifi cations Tips for Saving Energy Product code BUCL6082 AB170 Customer Helpline 0845 600 4632...
Safety Information Important Important - Please read these instructions fully before installation IMPORTANT - Please read this booklet before WARNING - This appliance is not intended for installing and switching on this appliance. The use by people (including children) with reduced manufacturer assumes no responsibility for physical, sensory or mental capabilities, or lack of incorrect installation and usage as described in this...
Before Using the Appliance Recommendations Switching on the appliance • Before switching on, place the appliance in an upright position and wait at least three hours without moving the appliance. This will give the freezing circuit time to settle and operate effi...
Parts Please check you have all of the attaching parts listed below Installation Installation kit contents Wood screw x17 B. Door hang C. Door Bottom Fixings x2 D. Hang cover E. Screw F. Top bracket Tools required Spirit level Screwdriver Setsquare Wrench Customer Helpline 0845 600 4632...
Installation Dimensions for installation Caution: 2 people are required to unpack and handle the larder. It is recommended that gloves are worn. a: Carefully remove all packaging materials and dispose of correctly. b: Make sure that the space available for the larder is large enough as per the dimensions (1).
Installation Fitting the door gasket Height adjustment a: Take out the gasket (G) located on the side panel, and remove the protective tape. b: Stick the gasket (G) on the larder side panel, on the opposite side to the door hinges, as shown (3). Height adjustment a: If necessary, the height of the larder can be adjusted, by loosening the locking nuts on the...
Installation Installation Installation Position the larder Caution: The larder may require 2 people Setsquare to handle it when pushing it into position. a: Check behind the larder to make sure there are no tools or obstructions that may cause damage. b: Carefully slide the larder into position until the hinge surface is aligned with the front surface of the kitchen unit.
Installation a: Unscrew and remove the nuts and washers from the appliance door. b: Place door hang (B) on the appliance door by inserting the holes to adjustment bolts. c: Dimension B= Measure from the underside surface of kitchen unit to the bottom of door hang. Dimension C= Measure from the underside surface of kitchen unit to the top of next unit door.
Page 11
Installation Installation f: Close the door and check the alignment with the other cabinet doors. g: Make the adjustment of the unit door by screwing or unscrewing the adjustment bolts for vertical adjustment and by the help of the slots on the door hang for other directions.
Installation k: Slide the hang cover (D) onto the door hang (B). Installing the plinth a: Position the plinth providing minimum 25 mm gap between the cabinet door and fi x it. Continued on next page Customer Helpline 0845 600 4632...
Installation Installation Installation Reversing the door a: Unscrew the screws on the front surface of the appliance door. Take the appliance door to a safe place. b: Move the hole plugs on the appliance door’s front surface, to the holes on the reverse side. c: Open the door upper hinge and door lower hinge, disassemble them.
without packaging. • To prevent cold air escaping, try not to open the larder door too often, and do not leave the door User Instructions open for long periods. User Instructions Thermostat setting • The thermostat automatically regulates the inside Do not try to rotate the knob beyond position 1 as temperature of the larder.
Cleaning and Maintenance General Warning: Disconnect the appliance from the power supply before cleaning. • Do not pour water over the appliance. • The larder compartment should be cleaned periodically using a solution of bicarbonate of soda and lukewarm water. •...
Trouble Shooting If your larder is not working properly there may be a minor problem, therefore check the following. Problem Possible Causes Possible Solutions The appliance does not operate There is a power failure The socket is defective. To check this, plug in a fully operable The mains plug is not properly appliance into the same socket...
Technical Specifi cations Technical Specifi cations Technical Specifi cations Model/Item AB170 Model/Item Model/Item AB170 AB170 Model / Item BUCL6082 Supplier’s name or trademark BUSH Supplier’s name or trademark Supplier’s name or trademark BUSH BUSH Supplier’s name or trademark BUSH Supplier’s model AB170 Supplier’s model...
Tips for Saving Energy 1. Install the appliance in a cool, well-ventilated room, but not in direct sunlight and not near a heat source (radiator, cooker etc.). Otherwise, use an insulating plate. 2. Allow food and drink to cool down outside of the appliance.
Page 19
Guarantee Product Guarantee This product is guaranteed against manufacturing defects for a period of Year This product is guaranteed for twelve months from the date of original purchase. Any defect that arises due to faulty materials or workmanship will either be replaced, refunded or repaired free of charge where possible during this period by the dealer from whom you purchased the unit.
Need help?
Do you have a question about the BUCL6082 and is the answer not in the manual?
Questions and answers