To change the master password for DVS part number 4, follow these steps:

1. Click on the User ID in the User column.
2. The password resetting screen will appear.
3. Input the new password and confirm it.
4. Choose ‘OK’ to confirm the setting.

This answer is automatically generated

Marlene or Clarence Hight

April 4, 2025

its 9 camera

Summary of Contents for DVS 4

Page 1 Standalone Digital Video Recorder Premium DVR 4, 8, 16 Channel Models User`s Manual MADE IN KOREA M2313PDCR This document contains preliminary information and is subject to change without notice.
Page 2 FCC Compliance Statement Notice to Users This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 3 Cautions  This product has free voltages (100V and 240V). See installation instructions before connecting to the power supply.  This product uses a Lithium battery.  To avoid any risk of explosion, do not replace the battery on the main board by anything other than a Lithium battery. ...
Page 4 12. Servicing  Do not attempt to service this equipment yourself. Refer all servicing to qualified service personnel. 13. Damage Requiring Service  Unplug this equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions: ①...
Page 5 The List of Configuration A Type 4 / 8 / 16CH DVR Set B Type 4 / 8 / 16CH CD (Software/Manual) Remote Controller Screws HDD Brackets Data Cable Power Cable...
Page 6: Operation Precautions
Operation Precautions  Power Off  Do not turn DVR off, or plug off the power adapter while DVR is in operation (record/playback). Otherwise, it may cause permanent damage to the equipment. Please click ( ) SETUP>SYSTEM>Shutdown sequentially and then remove the power after DVR is shutdown completely.
Page 7: Table Of Contents
Table of Contents Server LINK ..................39 PRODUCT FEATURES .............9 4.6.1 Alarm In ............... 39 4.6.2 Motion Event ............... 40 Unpacking ................9 4.6.3 Video Loss..............40 4.6.4 System Event .............. 41 4.6.5 Popup Link ..............41 Service ...................9 System Connection Diagram ..........9 OPERATION INSTRUCTION ..........
Page 8 Installation ..............95 8.5.2 HDD connections and Operating Status ......65 12.3.3 Site Registration ............96 8.5.3 Recording Status ............66 12.3.4 Connection ..............97 8.5.4 Motion Recording Status..........66 12.3.5 PTZ Control ..............98 8.5.5 Alarm In Connection and Operating Status ....66 12.3.6...
Page 9: Product Features
- Installation CD (CMS Software & User’s Manual) 1.2 Service  If there is any problem in the product, please refer servicing to a supplier or a distributor with qualified service personnel. 1.3 System Connection Diagram A Type - 4 / 8 / 16 Channel Series DVR...
Page 10 B Type - 4 / 8 / 16 Channel Series DVR...
Page 11: Installation
 Main substrate of this DVR has one SATA port: it is indicated as SATA 1.  Only one SATA device (hard disk) is possible to connect in Serial to the SATA port. Storage SATA 1, 2 Port 4 / 8 / 16 CH DVR (A and B Type) 2.1.2 HDD Installation ...
Page 12: Tcp/Ip(Ethernet) Connections
2.2.4 TCP/IP(Ethernet) Connections  Connect to ‘ETHERNET’ connector with the LAN cable.  When connect to Internet, use an ordinary LAN cable (Non-cross cable). However, when connect directly to a PC, please use only ‘Crossover cable’. 2.2.5 Alarm Connections  Connect Alarm Input (Sensor) to ‘AI 1~AI 2’ connectors and connect Sensor Common to ‘G’ connector.
Page 13: Input Device And Screen Icons
3. Input Device and Screen Icons 3.1 Front Panel A Type 4 / 8 / Channel DVR B Type 4 / 8 / Channel DVR KEYS PTZ KEY Operating mode Setup mode • Up/Down/Left/Right ▲, ▼, ◄, ► • Control Pan/Tilt rotation of up/down/left/right in PTZ mode...
Page 14: Screen Icon
Freeze Freeze on live/recorded display Shutdown (SETUP>SYSTEM>Shutdown) Picture in Picture function Cancel Cancel Function key menu En/Disable PTZ control 3.4 Screen Icon Icon Description Icon Description Continuous recording mode In Audio recording Event recording mode CMS access indication/ No. of accesses...
Page 15: Setup
4. Setup 4.1 Login / Logout  At the default setting of DVR, user have to input the password to enter the set up menu.  Please press SETUP key to enter the setup menu and the following screen will appear.
Page 16: System
4.2 SYSTEM 4.2.1 Information  Please click ( ) SYSTEM>Information and the following screen will appear. Status Site Description  Decide name of DVR.  Please click ( ) keyboard icon on Site Description frame and the following virtual keyboard will appear.
Page 17  Import: Copy the Menu setup stored in USB memory stick into DVR. Please plug in the memory stick and then click ( ) Import.  Export: Store the Menu setup of DVR in USB memory stick. Please plug in the memory stick and then click ( ) Export. ...
Page 18 Overwrite Setting  Click( ) Overwrite Setting button and the following screen will appear.  User shall designate the total recording days from 1 day to 30 days and unlimited.  User may set for beeping or notifying messages that notify the used percentage of disk. ...
Page 19: Admin
4.2.2 Admin  Please click ( ) SYSTEM>Admin and the following screen will appear. Date / Time Date  This menu will allow user to adjust the settings.  Please follow the procedure below for time adjustment. ① Click ( ) items (Y, M, D) to change. A designated item will be highlighted in a box (Y: Year, M: Month and D: Date).
Page 20 Time Format  Set time indication format. Please click ( ) Time Format frame to select a format from the list.  When user complete Date/Time input, please click ( ) NTP and the following screen will appear.  This menu is for accurate setting of time of day clock in DVR. ...
Page 21  Four rows will show as follows: - 1: SATA 1 Port Format  User must format when: - install new HDD - add another HDD - replace HDD - move HDD (change installation port) - remove HDD  Click ( ) Add/Remove frame in Format column and choose ‘OK’ on the dialogue box to start formatting. ...
Page 22: Account
- While pressing (+) or (-) button on the rightmost side of Temperature or HDD Damage item, a target value increases or decreases by 10 units.  Choose ‘OK’ to confirm the setting. 4.2.3 Account  Please click ( ) SYSTEM>Account and the following screen will appear.
Page 23: New User
New User  Please click ( ) New User and the following screen will appear.  Click ( ) the keyboard icon on the right-hand side of User Name frame and the virtual keyboard will appear. Click desired characteristics (up to 8 characteristics) on the virtual keyboard. ...
Page 24: System Log
 Input password by clicking the keyboard icon on the right-hand side of the frame.  Use key if wish to erase password on keyboard. 4.2.4 System Log  Please click ( ) SYSTEM>System Log and the following screen will appear.
Page 25: Exit
- Press Factory Reset Switch on the back panel. Please note that the entire menu setup is also defaulted. 4.2.5 Exit  Please click ( ) SYSTEM>Exit and choose ‘OK’ on the popup dialogue box to exit from the setting.
Page 26: Display
4.3 DISPLAY  Please click ( ) DISPLAY and the following screen will appear. 4.3.1  Please click ( ) DISPLAY>OSD and the following screen will appear.  The OSD menu will allow user to configure full features (i.e., on/off every letter and icon) displayed on the screen.
Page 27: Spot Monitor
 Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to 3>5>10>15>30>60 seconds by each press.  ‘4 Split Screen sequencing’ is disabled in the following modes. - 8 channel DVR: 3x3 Mode - 16 channel DVR: 4x4 Mode X9 Seq ...
Page 28: Spot Monitor Control On Display Mode
- SP mode: Sequential display is activated as configured on spot monitor Setup menu. - SP1 mode: Displayed channel on Spot monitor 1 can be changed by pressing channel button. Sequence stops at “SP1” mode. 4.4 DEVICES  Please click ( ) DEVICES and the following screen will appear. 4.4.1 Network ...
Page 29 Network Type  Please click ( ) Network Type. Every time click ( ), it changes to Static (fixed IP) and DHCP (floating IP).  In Static, user must manually set the static IP address for use. - Set IP Address, Subnet Mask and Gateway. Please ask your network administrator for more details. - To input address, please click (...
Page 30 Frames 1, 2, 3, 4, 5, 7, 15 frames for NTSC (1, 2, 3, 4, 5, 6, 12.5 frames for PAL) - Quality : Std. 1, Std. 2, Std. 3, Std. 4 (standard), High 1, High 2, High 3, Super 1, Super 2, Super 3 ...
Page 31: Camera / Ptz
SO PLEASE INACTIVATE THE SSL FEATURE IN THE SERVER SETUP. NOTE THAT SOME SERVER MAY NOT HAVE THIS INACTIVATE FEATURE CAUTION DEPENDING ON THE VARIOUS LOCAL CONDITIONS, SOME e-MAIL SERVERES MAY NOT WORK PROPERLY WITH THIS FUNCTION. 4.4.2 Camera / PTZ  Please click ( ) DEVICES>Camera/PTZ and the following screen will appear.
Page 32: Audio
 Click ( ) ▲, ▼ direction buttons on the right-hand side of the ID column to set ID number (i.e., 0 ~ 9999) of each PTZ.  While pressing (+) or (-) button, ID increases or decreases by 10 units.  Choose ‘OK’ to confirm the setting. 4.4.3 Audio  Please click ( ) DEVICES>Audio and the following screen will appear.
Page 33: Alarm In
 If users check on bind to cam, then the audio and video of same channel will come out. If not, the audio of unchecked channel will not come out. (The default audio channel is No. 1)  Choose ‘OK’ to confirm the setting. 4.4.4 Alarm In  Please click ( ) DEVICES>Alarm In and the following screen will appear.
Page 34: Serial In
 Choose ‘OK’ to confirm setting. 4.4.6 Serial In (NOTE) Please refer to “14 Serial In”. 4.5 RECORD  Please click ( ) RECORD and the following screen will appear. 4.5.1 Setting  Please click ( ) RECORD>Settings and the following screen will appear.
Page 35  Click ( ) each frame on Frames column to select recording rate of a corresponding camera. Recording rate varies by camera. Below lists the maximum recording rate of each camera. NTSC(PAL) 360x240 720x240 720x480 4 Channel DVR 120(100) 120(100) 60(50) 8 Channel DVR 240(200)
Page 36: Schedule
Below lists the maximum recording rate of each camera. NTSC(PAL) 360x240 720x240 720x480 4 Channel DVR 120(100) 120(100) 60(50) 8 Channel DVR 240(200) 120(100) 60(50) 16 Channel DVR 480(400) 240(200) 120(100)  Click ( ) each frame on Quality column to select recording quality of a corresponding camera. User may select one of Super, High and Std.
Page 37: Pre Alarm
 Choose ‘OK’ to confirm the setting. (NOTE) Holiday (H) registration is done with a separate menu. 4.5.3 Pre Alarm  Please ( ) RECORD>Pre Alarm and the following will appear.  Pre Alarm is effectively used when user selected recording mode by Alarm or Motion.
Page 38: Motion Detection
 Click ( ) each frame on Frames column to select recording rate of a corresponding camera. Recording rate varies by camera. Below lists the maximum recording rate of each camera. NTSC(PAL) 360x240 720x240 720x480 4 Channel DVR 120(100) 120(100) 60(50) 8 Channel DVR 240(200)
Page 39: Link
 Since holidays may vary every year, we recommend user to update on a regular basis.  Choose ‘OK’ to confirm the setting. 4.6 LINK  Please click ( ) LINK and the following screen will appear.  The LINK menu will allow user to set recording modes of all kinds of alarms (Sensor, Motion Event, Video loss, System Event, etc.), alarm output, e-mail notification and the like.
Page 40: Motion Event
 Choose ‘OK’ to confirm the setting. 4.6.2 Motion Event  Please click ( ) LINK>Motion Event and the following screen will appear.  Select cameras for recording while the motion sensor is in operation and alarm outputs and set up E-mail addresses for notification.
Page 41: System Event
⑤ Repeat the above procedure for Video Loss 2~ Video Loss 16.  Click No Beep  to deactivate alert sounds from video loss. Apply to all channel.  Choose ‘OK’ to confirm the setting. 4.6.4 System Event  Please click ( ) LINK>System Event and the following screen will appear.
Page 42  When Motion or Alarm-In is detected, user can select a popup or beep sound for warning, or have a particular channel of interest to pop-up on Spot Screen.  Please follow the setup procedures below. ① Select camera ② Popup: Please Check  a check box under making the popup screen for main monitor. ③...
Page 43: Operation Instruction
 At the normal state, HDD Overwrite mode is on and icon shows.  When Overwrite mode is off (see 4.2.1 Information>Record>Overwrite Setting), will show. And when the disk becomes full, the icon will be changed into ...
Page 44: Digital Zoom
In 8 channel DVR, 4-camera sequencing view mode is possible and in 16 channel DVR, 4 or 9-camera sequencing view modes are possible.
Page 45: System Log
 Available 1 ~ 255 Preset numbers can saved it depends on camera specification.  As explained earlier in 4.4.2. press Menu button to pop-up PTZ camera OSD setup screen and set up Tour and Pattern items. - Since these functions make use of a memory function of the camera itself, user should set them in Camera OSD.
Page 46: Search
5.2 Search  This involves searching recorded video to playback the wanted video of a specific date and time.  Press SEARCH key on the viewing screen, or Click Search menu at “Function Keys” and the following Search menu will appear.
Page 47: Event Search
 Follow the procedure below to search video by calendar. ① Select Year and Month by using the arrow buttons in the calendar. : search subsequent ‘Year’ : search previous ‘Year’ : search subsequent ‘Month’ : search previous ‘Month’ ② Click ( ) a date. The date will be displayed in black color. ③...
Page 48: Playback
5.3 Playback  This involves searching recorded video to playback the wanted video of a specific date and time in search mode.  Press SETUP key or please press the mouse right button and click in Playback mode. Then, the following screen will appear. ...
Page 49: One-Touch Playback
Go to End  Press SEARCH key to stop playing back video. 5.4 One-touch Playback  Press the PLAY/PAUSE key or double click the mouse wheel (central button) in the viewing mode. Then, user will be able to view the wanted recorded video right away without going through the search procedure. The video plays back the recorded video from the last one minute.
Page 50: Menu Bar
: Turn the display as 1 channel full screen. Additional click on full screen, it will change to next channel in sequence. : Turn the display as 4 channels split screen, Additional click on quad-screen, it will change to the next four channels in sequence.
Page 51: Color Control And Position
 Please click ( ) Color / Alarm in SEARCH popup menu or in front panel and the following input box will appear. (NOTE) THIS FUNCTION IS ENABLED ONLY WHEN LIVE MODE AND 4 SPLIT SCREEN MODE OR HIGHER. (NOTE)
Page 52  Please click ( ) Color / Alarm in SEARCH popup menu or in front panel and the following input box will appear.  Choose ‘Close’ to confirm the setting.
Page 53 Standalone Digital Video Recorder (Central Monitoring Station) User`s Manual This document contains preliminary information and is subject to change without notice.
Page 54: Program Installations
6. PROGRAM INSTALLATIONS 6.1 System Recommendations  Power on DVR and the following live video will appear, while viewing and recording at the same time. - Processor: Intel Pentium(R) (at 2.8GHz or higher) - Memory: 1.00GB or more - Video: 128 MB AGP VGA card, 1024 x 768 Resolution, 32-bit Color, DirectX® 8.1 version or later - HDD Space: 500 MB of space - Monitor: SVGA or XGA, 1024 x 768 Resolution, 32-bit Color - OS: Windows®...
Page 55: Login
⑥ When the following screen appears, select folder and click Next. ⑦ When the following screen appears, click Install. ⑧ When the following screen appears, click Finish to complete the installation. 6.3 Login  After install CMS software, CMS icon below appears on desktop. Please double click on the icon to execute the program.
Page 56: Function And Instructions
7. FUNCTION AND INSTRUCTIONS  Below lists are functions of the program. ICON ICON NAME WATCH MODE SEARCH MODE REMARKS System Log DVR System Log PTZ Control DVR PTZ Control System Health Check DVR System Health Check DVR Data Playback DVR Data Playback CMS(PC) Data Playback CMS(PC) Data Playback...
Page 57: Watch Mode
8. WATCH MODE 8.1 LOGIN Screen  When user login CMS, the following screen will appear. This screen is of Watch mode.  Because it is not connected to DVR, images do not show.  Please do Local Setting first before connecting to DVR. 8.2 Local Setting ...
Page 58: Remote Site
 Save Option: allow user to select Drive(C, D) and folder to save data.  Choose ‘OK’ to confirm the setting. 8.2.2 Remote Site  This menu is for Network setup.  Make CMS IP address and Port coincide with DVR. ...
Page 59 - Click “Scan DVR” button then IP address of DVR will be listed which is currently connected with PC in the network. - Select the IP address and click “Add site” then the connected DVR is automatically registered in the CMS. ...
Page 60: Live Video
8.3 Live Video 8.3.1 Network Connection  As the setup is completed, user should connect CMS to DVR over Network.  Please click in REMOTE DVR on the screen.  It will turn to blue, while being activated.  Please click REMOTE CONNECT button. ...
Page 61: Watch Mode
Quad Screen Mode: Click on QUAD SPLIT button and a quad screen will display. The quad screen is in combination of 1~4, 5~8, 9~12 and 13~16. If user selects Channel No. 7 and click the button, 5~8 quad screen will display.
Page 62: Multi Screen
 Camera Drag & Drop: Drag & Drop a camera of Remote Site to any screen. Then the camera will display. 8.3.4 Screen Color Adjustment  Adjust color of the screen using three bars (Brightness / Contrast / Saturation). Selecting a channel and dragging the bar(s) with a connected mouse.
Page 63: Audio
 Click on INSTANT RECORD button to save video of every channel in HDD of Local System (PC with CMS installation). 8.4 PTZ Control  This is for the control of Pan/Tilt of DVR.  Click on PTZ button in Watch mode and the following screen will appear.
Page 64 ① ② ③  Buttons on the screen have the following functions. ① Up/Down/Left/Right direction buttons ② Up/Down/Left/Right direction buttons Zoom Out/ In Focus Near / Far Iris Close / Open Preset Control / Go to Preset ③ Preset Control button The completed Preset ...
Page 65: Health Check
Camera is not in use.  Camera is not connected or Video Loss.  Camera is Covert status. 8.5.2 HDD connections and Operating Status  Camera is in normal operation.  HDD is not connected (up to 4).  HDD has an error.
Page 66: Recording Status
Recording Status Camera is in normal operation.   Recording is stopped.  Above the maximum number of cameras allowed. 8.5.4 Motion Recording Status  Camera is in normal operation.  Recording is stopped.  Above the maximum number of cameras allowed.
Page 67  The setup procedure is same as that of DVR.  When the setup is completed, do not click Exit button on the SETUP screen, but click OK or Cancel button on the Remote Setup screen.
Page 68: Search Mode
9. SEARCH MODE 9.1 Search Screen  This menu is for playing back recorded data.  Click on REMOTE SEARCH button in Watch mode and the following Screen mode screen will appear.  Search mode provides three search functions. One is for searching DVR video by clicking REMOTE SEARCH button and another is for searching video stored in CMS (HDD of PC) by clicking LOCAL SEARCH button and the other is for searching event recorded data stored in DVR by clicking REMOTE EVENT button.
Page 69: Remote Search
9.2 Remote Search  The REMOTE SEARCH button allows user to playback recorded video of DVR.  Select Date - In Calendar, dates with recorded data are marked in blue. - Click the wanted date among the dates marked in blue. In background of Time Select Bar, data recorded time is displayed in bar shape.
Page 70: Event Search
9.4 Event Search  The REMOTE SEARCH button allows user to search event recorded data of DVR. ① Designate Event Search start time. ② Designate Event Search end time. ③ Select camera (video) to search data. ④ Check a check box (Motion/Alarm In/Emergency/Serial in) Check box.
Page 71: Print
 Input the name of the file to save and execute Save. CAUTION If images are not saved properly, click UNDO button and save again. 9.5.4 Archive  This is to back up the DVR’s moving image data to EXE file in PC(CMS).
Page 72 ① Designate Archive start time. ② Designate Archive end time. ③ Designate file name. ④ Select camera (video) to save. ⑤ Click on Start button to begin Archive.
Page 73: Others
10. Others 10.1 Viewer  The Format of archive file is .exe(executable file).  Please double click on the icon to execute the program. PLAY • Playback mode: 1X PLAY • Playback mode: PAUSE PAUSE • Frame-by-frame backward still image BACKWARD playback •...
Page 74  Please click on the icon to load the image file.  To move the icon just drag and drop.  You can also rotate the icon.  Please click on the icon and input the name of the E Map file to save and execute. ...
Page 75: Watermark Check System
EXE to AVI Converter  Users are able to convert Archived file(EXE format) to AVI format.  Users will be required a converting codec between “ Microsoft MPEG-4 codec” and “XVID MPEG-4 codec” or able to use both.  Both are able to download freely in many web-sites.
Page 76  Click “File Open” and choose an Archived file(EXE format).  Click “EXE to AVI File” and select a directory to save the converted AVI file.  Select a channel to convert (Only one channel can be converted at once). ...
Page 77: Cms Web Client
CMS Web Client CMS Web Client User`s Manual This document contains preliminary information and is subject to change without notice.
Page 78: Setup And Login
11. CMS WEB CLIENT 11.1 Setup and Login  MS Explorer web browser is required for installation and using this program.  Open a browser and type the IP address of DVR.  It is required to install ActiveX in the first connection. ...
Page 79: Live Display
Zoom In / Zoom Out control button. Focus Near / Focus Far control button. ④ Select display split mode. User can choose 1, 4, 9, 16 split display consequently. - Check boxes for hiding/showing text from OSD. ⑤ Channel selection button - available to check the channel (camera) number of current display.
Page 80: Playback Screen
Go to the Previous Image Go to the Next Image ⑤ Select display split mode. User can choose 1, 4, 9, 16 split display consequently. - Check boxes for hiding/showing text on OSD. ⑥ Indicate the recorded data in Time bar figure.
Page 81: Cms Mobile Viewer
CMS Mobile Viewer CMS Mobile Viewer User`s Manual This document contains preliminary information and is subject to change without notice.
Page 82: Iphone Mobile
12. CMS MOBILE VIEWER 12.1 iPhone Mobile 12.1.1 System Requirements  There are no other requirements to run this program because it is specialized to perform on iPhone interface. 12.1.2 Installation  Turn on the iPhone then connect to App Store. ...
Page 83  Select “ ” program which is offered from dvrdomain by free.  When user clicks a “ ” button, it will be turned to “ ”  Click “ ” to start installation.  If user already has a iTunes account, then input user’s account to download the program. ...
Page 84: Site Registration
 When user registered the account, the program will be automatically installed. 12.1.3 Site Registration  Click “ ” icon on iPhone menu then below will show.  Move to “ ” and enter site information which are same as CMS site registration. ...
Page 85: Connection
 Enter ID/Password.  Click “ ” to save the setting. 12.1.4 Connection  On “ ” window, click one of the registered site and click “ ”.  Click “ ” to connect the DVR to the iPhone.  To select other channels, click the channel bar below the Site Name.
Page 86: Search
12.1.5 Search  Users are able to search the recorded data in the mobile CMS program.  Click “ ” to use search function of the application.  click “ ” for date setting.  If users click “ ”, then the month with recorded data will show up.
Page 87  Choose the month that wish to search and click “ ”.  Click “ ” to select the date in the month and click “ ”  Click “ ” to select the time of the date of the recorded data. ...
Page 88: Ptz Control
12.1.6 PTZ Control  Users are able to control PTZ with iPhone by touching the screen.  Touch and drag upside on the center of the screen to zoom out.  Touch and drag downside on the center of the screen to zoom in. ...
Page 89: Disconnection
12.1.8 Disconnection  When disconnecting, please click “ ” and exit the mobile viewer program. 12.1.9 Uninstallation  Click the “ ” icon and hold for a while until the program icon shows x mark on the top-left side.  Click the “ ”...
Page 90: Android Phone
12.2 Android Phone 12.2.1 System Requirements  This program is designed and applied only for Android OS(version 1.6 or higher) based Smart phones. 12.2.2 Installation  Turn on the phone then connect to Android Market.  Move to search menu and type “mviewer” then select “ ”...
Page 91: Site Registration
 Click “ ” then “ ” to start installation.  The program will be automatically installed in user’s application menu. 12.2.3 Site Registration  Click “ ” icon on application menu then below will show.  Move to “ ”...
Page 92: Connection
” icon below the Site Name.  16 channel multi view is available for CIF resolution.  4 channel multi view is available for H.D1 and D1 resolution.  Only 1 channel view(full screen) is available for 720p and 1080p.
Page 93: Audio
 Users are able to search the recorded data in the mobile CMS program.  Click “ ” to use search function of the application.  click “ ” to select the month, the date and the time in order. ...
Page 94: Information
 Touch sides and corners of the screen to change the direction as user want.  Touch right side of the screen to move right and left side to move left.  Touch up side of the screen to move up and down side to move down. ...
Page 95: Uninstallation
 When disconnecting, please click " ” and exit the mobile viewer program. 12.2.10 Uninstallation  Move to Setup > Application > Manage Applications then select “ ”.  Click “ ” icon then it will ask to delete the program. ...
Page 96: Site Registration
 Click “search” icon and type “DVR Viewer” program.  Select the “DVR viewer” which is offered from dvrdomain by free and start to install the program by clicking the icon. 12.3.3 Site Registration  After downloading the program, click “ ”...
Page 97: Connection
 If the site is registered appropriately, the following screen will be shown.  Click “Menu>Connect” to connect the site.  Users can select the display mode from 1, 4, 9 and 16 multi view.  16 channel multi view is available for CIF resolution.
Page 98: Ptz Control
 Press 1~9 number buttons to change directions as user want.  For example, click no. 4 to move left and no.6 to move right.  In the same way, click no.2 to move upside and no.8 to move downside.
Page 99: Symbian Mobile
12.4 Symbian Mobile 12.4.1 System Requirements  This program is designed and applied only for Symbian OS based Smart phones. 12.4.2 Installation  Turn on the phone then connect to ovi store.  Move to “Search all items” and Type “dvr viewer” then click “Search”...
Page 100  When user clicks a DVR Viewer icon, it will be changed to login page.  If user does not have the account, then click “create a Nokia account” and it is registered by free.  Type e-mail address and password and select country and type the identified text shown at the below, then you can click “OK”...
Page 101: Site Registration
 When users registered the account, then click “download”  When downloading has been completed, Click “Launch” to complete the installation. 12.4.3 Site Registration  Click “DVR Viewer” icon on Symbian menu then below will show.
Page 102: Connection
 Enter the information which is similar as CMS site registration.  Enter site Name, IP.  Enter Admin/Stream port value.  Enter ID/Password  Click “Submit” to save the setting. 12.4.4 Connection  Click one of the registered site and then select “options” to click “Connect” to choose connection.
Page 103  Choose available connection and it will start connecting the DVR to the Symbian.  Choose required channel to display.  Selected channel will be displayed.
Page 104: Ptz Control
12.4.5 PTZ Control  Users are able to control PTZ with Symbian by touching the screen.  Touch sides and corners of the screen to change the direction as user want.  Touch right side of the screen to move right and left side to move left.
Page 105: Information
12.4.6 Information  Click “Options” and select “About” to check the information of the application. 12.4.7 Disconnection  When disconnecting, please click “Disconnect” and exit the mobile viewer program. 12.4.8 Uninstallation  Click “option” and select “Remove” to uninstall the program.
Page 106: Windows Mobile
12.5 Windows Mobile 12.5.1 System Requirements  OS : Windows Mobile Professional 6.1 or higher version.  Memory : 512Kb or Higher.  Device : Smartphone  Network : Available all wireless networking method. I.e. Wi-fi, HSDPA, Wibro. 12.5.2 Installation ...
Page 107  Click accepting the license agreement, then click “Finish” button.  Installation box will appear.  Click [OK] to start installation.  When installation completed, following pop-up will appear.  Click [OK].  If following message appeared, it has successfully installed. (NOTE) Depending on mobile device, successful installation message may not appear.
Page 108: Site Configuration
12.5.3 Site Configuration  Click [Add] to appear following screen.  Fill in correct information. - Site Name : Insert the name of site. - IP/Domain : Insert the IP address or Domain name of the site. - ID : Input the registered ID of the site. - Password : Input the password of the registered ID.
Page 109: Connection
 Correct items then click [Save]. Delete  Select a site and click [Del].  Confirmation message will pop up.  Click [Yes] then the site information will be removed. 12.5.4 Connection  Select a site then click [Connect].
Page 110: Uninstall
 Live display screen of the site will appear if it is successfully connected.  Users are able to select a camera by clicking camera button.  Click [Disconnect] then, live display screen will be closed and Site list box will appear. 12.5.5 Uninstall ...
Page 111: Keyboard Controller
Keyboard Controller Keyboard Controller CP1200A User`s Manual This document contains preliminary information and is subject to change without notice.
Page 112: Connection
13. KEYBOARD CONTROLLER 13.1 Connection  User may connect cameras and Keyboard through DVR in various ways.  Below shows the major probable connection methods through RS-485; 13.1.1 Configuration Diagram I  Single system configuration (1 Camera, 1 DVR) DVR PTZ Port RS485 RS485 Tx1+...
Page 113: Configuration Diagram Iii
13.1.3 Configuration Diagram III  Multiple system configuration (Multi Cameras, Multi DVRs) Max 16 camera RS485 RS485 RS485 RS485 … … … … Multi port Max 16 DVR DVR 1 DVR 2 … … Multi port  Please make sure to connect “Tx to Rx “or “Rx to Tx” with positive polarity. (+ to +) and (- to -). 13.2 Keyboard Setup in DVR ...
Page 114: Keyboard Configuration
 In DVR control mode, all buttons are operated according to texts written underneath of each button. The functions are same as Front buttons of DVR as follows: - DISPLAY: change channel split screens in sequence of 1>4>9>16>1. - SEQ: turn on/off Sequence function.
Page 115: Ptz Control Mode
PIP channel. In case of 4 or 9 channel screen, it changes the screen to a next one in the sequence. - FREEZ: freeze a current image. - SETUP: pop up Setup window. - PLAY/PAUSE: play/pause recorded data in play mode.
Page 116 Serial In (POS / ATM) Serial In (POS / ATM) User`s Manual This document contains preliminary information and is subject to change without notice.
Page 117: Serial In (Pos/Atm)
Connection Method  Four ATM/POS channels are available as a default.  Connect the USB slot of DVR by using USB to RS-232 Converter Cable and it is available to connect up to 4 serial-in devices by using the converter.
Page 118: Link
14.4 Link 14.4.1 Link Setup  Click “Setup>Link>” then shows as below. (NOTE) The above menu is only available on the DVR model with Serial-In function.  Click “Serial In” to appear following screen.  Select POS/ATM port by clicking ‘Serial In’ button.
Page 119: Setup
 Tick the box(□) item Alarm In.  Click the Time/Date that wishes to activate ATM/POS function on schedule.  It is possible to activate all the time by clicking top-right side of table.  Click “OK” to save the schedules. (NOTE) Please do not select the Alarm In and Motion simultaneously on schedule setup.
Page 120: Osd Display
 User can select the name of serial device if click ( ) the keyboard button of Title.  When “Use” items of Numbers 1-4 are checked on Serial-In page, it receives the data from the applicable serial device.  Check the “Auto” item so as to capture automatically all the data which includes unnecessary dummy data out of serial device as below.
Page 121  Input a certain repeated string to “Line Delimiter”.  Decide the number of minimum characters in “MCPL” item to hide data under the designated number of characters.  Input the pattern of dummy data to Discard Pattern.  Choose the data which willing to display and enter the Start Pattern and End Pattern.
Page 122: Search
 Then tick the Auto box off in order to make the DVR recognizes the data between the Start and End patterns.  Finally, test again and adjust data to remove missed dummy data. 14.6 Search  Using event search function. ...

This manual is also suitable for:

8 16

DVS 4 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for DVS 4

Summary of Contents for DVS 4

This manual is also suitable for: