Table of Contents
Advertisement
N95RHN
PNEUMATIC STICK NAILERS
CLAVADORA NEUMÁTICA ALIMENTADA POR BARRA
CLOUEUR PNEUMATIQUE EN BANDES
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D'INSTRUCTIONS ET D'ENTRETIEN
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL,
TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU
HAVE ANY QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DIS-
TRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN
ESTUDIAR ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVER-
TENCIAS SOBRE SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS
INSTRUCCIONES CON LA HERRAMIENTA PARA FUTURA REFERENCIA. SI TIENE
ALGUNA DUDA, COMUNÍQUESE CON SU REPRESENTANTE DE BOSTITCH O CON
SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D'UTILISER L'APPAREIL.
PRÊTER UNE ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ
ET AUX AVERTISSEMENTS. GARDER CE MANUEL AVEC L'OUTIL POUR FUTURE
RÉFÉRENCE.
SI
VOUS
AVEZ
DES
QUESTIONS,
CONTACTEZ
VOTRE
REPRÉSENTANT OU VOTRE CONCESSIONNAIRE BOSTITCH.
102953REVG 5/00
Stanley Fastening Systems
Advertisement
Table of Contents
Related Manuals for Bostitch N95RHN
Summary of Contents for Bostitch N95RHN
- Page 1 ESTUDIAR ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVER- TENCIAS SOBRE SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA PARA FUTURA REFERENCIA. SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR. LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL.
-
Page 2: Table Of Contents
INTRODUCTION The Bostitch N95RHN is a precision-built tool, designed for high speed, high volume nailing. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer’s instructions must be followed. -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. -
Page 4: Tool Specifications
DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE. AIR CONSUMPTION: The N95RHN requires 7.8 cubic feet per minute of free air to operate at the rate of 100 nails per minute, at 80 p.s.i.g. (5.6 kg/cm ). Take the actual rate at which the tool will be run to determine the amount of air required. -
Page 5: Air Supply: Fittings, Hoses, Filters, Air Consumption, Regulators, Operating Pressure, Setting Correct Pressure
Frequent, but not excessive, lubrication is required for best performance. Oil added through the air line connection will lubricate the internal parts. Use BOSTITCH Air Tool Lubricant, Mobil Velocite #10, or equivalent. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool mainte- nance. -
Page 6: Loading The Tool
It is not necessary to remove these nuts. Move the lower portion of the NOTE: Use only All-Specs™ nails rec- depth control to the desired height and tighten the nuts. Do not ommended for use in Bostitch N95RHN overtighten. Check that the work contacting element operates freely without sticking or binding. -
Page 7: Tool Operation
THIS MANUAL. II. REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL. There are two available systems on BOSTITCH pneumatic tools. They are: 1. CONTACT TRIP OPERATION 2. SEQUENTIAL TRIP OPERATION OPERATION 1. CONTACT TRIP OPERATION The CONTACT TRIP MODEL tool contains a contact trip that operates in conjunction with the trigger to drive a fastener. -
Page 8: Tool Operation Check
IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANU- AL OBSERVE THE FOLLOWING FOR SAFE OPERATION • Use the BOSTITCH pneumatic tool only for the purpose for which it was designed. • Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area. -
Page 9: Maintaining The Pneumatic Tool
Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force. REPLACEMENT PARTS: BOSTITCH replacement parts are recommended. Do not use modified parts or parts which will not give equivalent performance to the original equipment. ASSEMBLY PROCEDURE FOR SEALS: When repairing a tool, make sure the internal parts are clean and lubricated. -
Page 10: Trouble Shooting
Broken/chipped driver ... . .Replace driver (check piston O-ring) Dry/dirty magazine ....Clean/lubricate use BOSTITCH Air Tool Lubricant Worn magazine . -
Page 11: Driver Maintenance/Directional Exhaust
Loosen screw as shown. Adjust to desired exhaust direction and tighten screw. ACCESSORIES AVAILABLE BC601 4 oz. Bostitch Air-Tool Lubricant. BC602 1 pint Bostitch Air Tool Lubricant. BC603 1 pint Bostitch “Winter-Formula” Air-Tool Lubricant. BC604 1 quart Bostitch Air-Tool Lubricant SEQ1 Sequential Trip Conversion Kit.
Need help?
Do you have a question about the N95RHN and is the answer not in the manual?
Questions and answers
What angle nail