Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for youli MIG-160PI
- Page 1 USER'S MANUAL MODEL： ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 1 -...
-
Page 2: Safety Caution
·If trouble in installation and operation, please follow this manual instruction to check up. ·If fail to fully understand the manual, or fail to solve the problem with the instruction, you should contact the suppliers or our service center for professional help. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 2 -... -
Page 3: About The Machine
Thanks for purchasing product and hope for your precious advice. We will dedicate to produce the best products and offer the best service. CAUTION！ The machine is mainly used in industry. It will produce radio wave, so the worker should make fully preparation for protection. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 3 -... - Page 4 PARAMETERS MIG-160PI MIG-180PI MIG-200PI MIG-250PI Model 1 phase 1 phase 1 phase 1 phase Power Vol.（V） 220V15% 220V15% 220V15% 220V15% Frequency（HZ） 50/60 50/60 50/60 50/60 Rated input current（A） 20.2 23.8 27.6 Output current （A） 50-160 50-180 50-200 50-250 Output Vol. (V) 16.5-22...
- Page 5 To prevent the bent wire from getting stuck, please cut off this part of the wire. 7) The MIG torch has been setted inside of the machine just need put the wire into the torch by hand. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 5 -...
-
Page 6: Operation
4、 Tune the voltage knob,speed knob and inductance knob to the right position based on the thickness of the work piece and mechanics. 5、Press the torch switch to let out the wire to the torch head and begin to work. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 6 -... -
Page 7: Notes Or Preventive Measures
NOTES OR PREVENTIVE MEASURES 1、Environment 1）The machine can perform in environment where conditions are dry with a dampness lever of max 90%. 2）Ambient temperature is between 10 to 40 degrees centigrade. 3）Avoid welding in sunshine or dripaings. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 7 -... -
Page 8: Safety Norms
User must try to improve welding environment. A、Arcing-striking is difficult and easy to pause： 1) Make sure the earth cable clincher connects the work piece well. 2) Check each connecting point connected or not. B、Output current can not reach rated volume： ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 8 -... -
Page 9: Maintenance
Box And store in dry environment. 6、When wire machine operates for every 300 hours, the electric carbon brush and armature rectifier should be polished, the reducer should be cleaned, and lubricator should be added to the turbo and bearing. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 9 -... -
Page 10: Check Fault
Maybe secondary rectifier tube of transformer is damaged, find out faults and replace rectifier tube with it. If the machine fails to work normally after maintenance and check, please contact us.We will do our best to support you the useful suggestions. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 10 -... -
Page 11: Check Faults
1、 Wheel and leading tube not match 2、 Wheel broken, slot blocked Wire sending 〇 〇 〇 〇 〇 or lack equipment 3、 Over pressing or loosen, powder store up in entrance of SUS tube DAILY CHECKING ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 11 -... -
Page 12: Welding Torch
Forget to insert or the hole May lead to vice (splash) because of blocked, different factory poor gas shield, torch body get burned bypass component. (arc in the torch), please handle. DAILY CHECK ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 12 - WIRE SENDING MACHINE... - Page 13 1.If the earth cable that connects the power supply is To prevent creep age Earth broken and connect tightly. insure security, cable 2. If the earth cable that connects the main part is please make daily broken and connects tightly. check. ·MIG-160PI/MIG-180PI/MIG-200PI/MIG-250PI - 13 -...
Need help?
Do you have a question about the MIG-160PI and is the answer not in the manual?
Questions and answers