Table of Contents
Advertisement
MODEL
HT-SB20
HT-SB30
SOUND BAR HOME THEATER SYSTEM
ON /
ST AN D-
MU TE
MO DE
SO UN D
NE WS
MU SIC
A
CIN EM
INP UT
ND
SU RR OU
BY PA SS
TV
CH
VO L
VO L
WS A
GA 32 2A
RR MC
(HT-SB30 only)
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other
trademarks and trade names are those of their respective owners.
Note: This product is recommended for flat panel TV (LED, LCD and plasma).
Caution: Before operating this product, refer "IMPORTANT SAFEGUARDS AND
10 :
*TINSZB534AWZZA6*|
TINSZB534AWZZ
OPERATION MANUAL
BY
WARRANTY" at the reverse page of English operation manual.
ENGLISH
Printed in Malaysia
1
13A R AS
Advertisement
Table of Contents
Related Manuals for Sharp HT-SB20
Summary of Contents for Sharp HT-SB20
-
Page 1: Operation Manual
(HT-SB30 only) The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and trade names are those of their respective owners. Note: This product is recommended for flat panel TV (LED, LCD and plasma). -
Page 2: Controls And Indicators
Remote Sensor On/Stand-by Left Channel Button Speakers Surround Button Right Channel Surround Indicator Speakers SOUND BAR HOME THEATER SYSTEM HT-SB20 Volume Indicator Volume Down Button SOUND BAR HOME THEATER SYSTEM HT-SB20 Front Panel (HT-SB30) ■ 3 4 5 8 9 10... -
Page 3: Rear Panel
Turn up/down the TV Channel Up and Switch up/down the TV and Down volume. Down Buttons channels. Buttons Note: ● Some models of SHARP TV may not be operable. ● SHARP TV remote control will not work with HT-SB20/HT-SB30 system. -
Page 4: System Preparation
3/8” (8-9 mm) Driving screws ■ SHARP designed the sound bar so you may hang Wall surface it on the wall. Use proper screws (not supplied). Fasten the screws to the wall as shown below. See below for size and type. -
Page 5: Placing The Sound Bar
Placing the sound bar Notes: Installation image: Remove the protective film covering the sound ● bar before turning on the system. The front panel of the sound bar is not ● removable. Place the sound Caution: bar as Do not change the installation direction when ●... - Page 6 When mounting on the wall ■ Screw eye (not supplied) Safety wires (not supplied) SOUND BAR HOME THEATER SYSTEM HT-SB30 Sound bar Wall When placing on the shelf/table ■ Sound bar Screw eye Safety (not supplied) Rack/ wires table (not supplied) Screw eye (not supplied)
-
Page 7: Sound Bar Connections To Tvs
Sound bar connections to TVs Caution: Turn off all other equipment before making any connections. Notes: ● To connect to TV, use Audio IN terminals located at the rear of the sound bar. ● Refer the operation manual of the equipment to be connected. ●... -
Page 8: Ac Power Connection
AC power connection After checking all the connections have Make sure to unplug the AC power been made correctly, connect the AC cord before making any connections. power cord to the AC power input jack, then to the AC outlet. AC/DC Adaptor Using with the AC/DC adaptor ■... -
Page 9: Remote Control
Remote control battery holder, insert the new bat- Battery installation ■ tery and then slide the battery hold- er back into the remote control. WARNING Positive (+) Battery holder side up Polarity DO NOT INGEST BATTERY, (+) symbol CHEMICAL BURN HAZARD Battery type The remote control supplied with this ●... -
Page 10: General Control
Press the desired sound mode button Note: on the remote control. If the power does not turn on, check whether HT-SB20 the power cord is plugged in properly. The VOLUME indicator: blinks once To set the sound bar to stand-by mode: Press the ON/STAND-BY button again. - Page 11 Listening to Bluetooth enabled devices (for HT-SB30) Audio stream About Bluetooth technology ■ ON/STAND-BY SOURCE PAIRING SURROUND VOLUME Bluetooth wireless technology is a short-range radio SOUND BAR HOME THEATER SYSTEM HT-SB30 technology that enables wireless communication Bluetooth mobile phone or other Bluetooth Stereo audio source device between various types of digital devices, such as mobile phone or computer.
- Page 12 Repeat Perform pairing procedure on the source step 1 onwards to start pairing again. device to detect this sound bar. “SHARP To pair with other devices, repeat steps 1 - 5 HT-SB30” will appear in the detected de- ●...
-
Page 13: Listening To The Sound
Listening to Bluetooth enabled devices (for HT-SB30) (continued) Listening to the sound To finish listening ■ ■ Check that: Perform any of the followings. The source device Bluetooth functionality is ON. - Disconnect the Bluetooth connection on the audio ● Pairing of this sound bar and the source device source device. -
Page 14: Troubleshooting Chart
(Refer to If something is wrong with this product, check the page 7.) following before calling your authorized SHARP The protection circuit ● dealer or service center. may be activated. Unplug and plug in the... -
Page 15: Error Indicators And Warnings
. During Stand-by mode. HT-SB20 Press and hold SURROUND button and the ON/STAND-BY button. HT-SB30 Press and hold PAIRING button and the ON/STAND-BY button. -
Page 16: Maintenance
Specifications Cleaning the cabinet ■ As part of our policy of continuous improvement, SHARP reserves the right to make design and Periodically wipe the cabinet with a soft cloth. specification changes for product improve- ment without prior notice. The performance...