Page 1
Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E1C E1K AVR-X2100W P P P AVR-S900W INTEGRATED NETWORK AV RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied.
TECHNICAL SPECIFICATIONS FOR AVR-X2100W n Audio section Network type (wireless LAN standard): Conforming to Wi-Fi®z1 • Power amplifier Security : WEP 64 bit, WEP 128 bit Rated output : WPA/WPA2-PSK (AES) Front : WPA/WPA2-PSK (TKIP) 95W+95W(8Ω, 20Hz - 20kHz with 0.08% T.H.D.) 125W+125W(6Ω, 1kHz with 0.7% T.H.D)
TECHNICAL SPECIFICATIONS FOR AVR-S900W n Audio section n Wireless LAN section • Power amplifier Network type Rated output : (wireless LAN standard): Conforming to Wi-Fi®z1 Front : Security : WEP 64 bit, WEP 128 bit 90W+90W(8Ω, 20Hz - 20kHz with 0.08% T.H.D.) WPA/WPA2-PSK (AES) 125W+125W(6Ω, 1kHz with 0.7% T.H.D) WPA/WPA2-PSK (TKIP)
Initialize this unit if you have replaced the microcomputer, one of the parts around the microcomputer, or the digital PCB. Press the power button to turn off the power. AVR-X2100W Hold down buttons "ZONE2 SOURCE" and "DIMMER" at the same time and press the power button to turn on the power.
DISASSEMBLY • Remove each part in the order of the arrows below. • Reassemble removed parts in the reverse order. • Read "Precautions During Work" before reassembling removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Page 13
Explanatory Photos for DISASSEMBLY • The angles from which the photos are taken are shown by "Photo angle: A, B, C, D". • See the diagram below about the shooting direction of each photograph. • Photographs with no shooting direction indicated were taken from the top of the unit. •...
1. FRONT PANEL ASSY TOP COVER → FRONT PANEL ASSY Proceeding : (1) Remove the screws. View from the bottom (2) Cut the wire clamp, then remove the connector wires and FFC. Remove the screws. Front side CP4400 STYLE PIN N7002 N7005...
3. HDMI PCB TOP COVER → BACK CHASSIS → Proceeding : HDMI PCB (1) Remove the screws. (2) Cut the wire clamp, then remove the connector wires and FFC. Front side STYLE PIN CON1 N1029 CON2 N7002 N7005 STYLE PIN (3) Remove the connector wire.
4. VIDEO PCB TOP COVER → BACK CHASSIS → → VIDEO PCB Proceeding : HDMI PCB (1) Remove the connector wire. Front side CN5004 CN5001 CN5000 CN5003 MAIN PCB TOP COVER → BACK CHASSIS → → VIDEO PCB → Proceeding : HDMI PCB MAIN PCB (1) Remove the screws.
↑ ↑ Mode Audio channel/video channel. (See page) If there are multiple DENON AV receivers in the same area, this mode stops the other AV receivers from being oper- Remote ID Setup Mode ↑ ↑ ↑ ated concurrently with this device.
↑ ↑ Mode channel/video channel. (See page) If there are multiple DENON AV receivers in the same area, this mode stops the other AV receivers from being oper- Remote ID Setup Mode ↑ ↑ ↑ ated concurrently with this device.
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up Hold down buttons "DIMMER" and "STATUS" at the same time and press the power button to turn on the power. Press the "STATUS"...
Page 22
o Ethernet 1st Boot Loader, Hardware ID : E t h e r n e t F B L Press the "STATUS" button. * * * * * * - b d Q0 Ethernet 2nd Boot Loader, Rhapsody Flag : E t h e r n e t S B L Press the "STATUS"...
1.4. Error display See the table below for descriptions of displayed errors and countermeasures for these. Display order is q , w , e , r . Condition States Display TROUBLE SHOOTING The model name, brand name and region F I R M E R R O R information written in the firmware are compared to the region settings in the...
Page 24
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware Version XXXX - XXXX - XXXX...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Turn the PANEL LOCK and REMOTE LOCK modes on and off. 2.2. Starting up Hold down buttons "TUNER PRESET CH+" and "ZONE2 SOURCE" at the same time and press the power button to turn on the power.
Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 3.2. Starting up AVR-X2100W Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
Page 28
The Video and Audio paths can be checked. The backup data is not rewritten. 3.4.2. Starting up AVR-X2100W Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power. AVR-S900W Hold down buttons "TUNER PRESET CH +", "TUNE -"...
Page 29
A 1 1 : A S S I G N - B i A M P (Amp Assign: Bi-Amp) Input Mode : Auto ・Check of Analog input ⇒ Speaker output. AVR-X2100W Only Sound mode: MULTI CH STEREO Surround Back L/R fig.13 Amp assign : Bi-Amp (※...
Page 34
fig.04b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 36
fig.06 ADV8195 TMDS IN FRONT HDMI BUFFER TMDS OUTPUT HDMI OUT1 TMDS IN HDMI2.0 HDMI1 HDMI2.0 Matix SW Matix SW MN8647781 MN8647781 HDMI2 MX25L12845EMI-10G 128M TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 TMDS OUT HDMI4 HDMI Rx HDMI2.0 HDMI i/p Scaler_TX_OSD HDMI5...
Page 37
fig.07 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 39
fig.08b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 41
fig.09b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 43
fig.10b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 45
fig.11b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 46
fig.12 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 47
fig.13 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 49
fig.14b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL Bypass DSP_FL Tone EXT_FL Tone+Mix ANALOG ANA_FR Tone+Mix SAT_CBL Tone DSP_FR INPUT EXT_FR Bypass DVR/VCR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR ONLY PREOUT DSP_SW TUNER EXT_SW ALL MODEL : FM/AM AVR_E900 / X2100 : 0.2ch...
Page 50
This mode records and displays an event in which the THERMAL, ASO or DC protection was activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.5.2. Starting up AVR-X2100W ·Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
Page 51
3.5.4. Clearing the Protection History There are two ways to clear the protection history. (1) Start Protection History Display Mode. Press the button "STATUS" to display the protection history. Press and hold the button "DIMMER" for 3 seconds. P R T : D C Press and hold the button "DIMMER"...
Page 52
This mode displays the accumulated operating time, power on count and each protection count. 3.6.2. Starting up AVR-X2100W ·Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
Page 53
This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.7.2. Starting up AVR-X2100W ·Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
4. Remote ID Setup Mode 4.1. Actions This function allows only the desired AV receiver to be operated if multiple DENON AV receivers are used in the same room. 4.2. Starting up AVR-X2100W ·Hold down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" at the same time and press the power button to turn on the power.
• This is the same as normal power-on, except that protections are not activated. 5.2. Operations AVR-X2100W · Hold down buttons "TUNER PRESET CH +", "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power.
(6) User ID (7) Resume Playback station 7.2. Operations AVR-X2100W ·Hold down buttons "ZONE2 SOURCE" and "DIMMER" for at least 3 seconds while the power is on. AVR-S900W ·Hold down buttons "TUNER PRESET CH +" and "TUNE -" for at least 3 seconds while the power is on.
JIG FOR SERVICING The following jigs (extension cable kit) are used when repairing the PCBs. Order the jigs from your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for HDMI PCB -Items to Be Prepared- 8U- 110084S EXTENSION UNIT KIT 1 Set...
Page 58
Front side CN5004 CN5001 CN5000 CN5003 (3) Remove the HDMI PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the HDMI PCB. Connect the earth of the PCB to the chassis using an earth wire, etc. PCB HDMI PCB VIDEO Insulation sheet...
Page 59
(4) Connect the expansion cables. PCB HDMI PCB FRONT CNT PCB HDMI PCB INPUT PCB VIDEO PCB FRONT CNT PCB VIDEO PCB INPUT Connection table of Board to Board Ref. No. Ref. No. 17pin CP3404 FRONT CNT N1018 HDMI 11pin CP3401 FRONT CNT N1033 HDMI 23pin CP4200...
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Proce- dure after PCB Name Ref. No. Description Remark Replace- ment U1018 R5F56108VNFP 32BIT SOFTWARE: Main HDMI U1020 R5F5210ABDFP SOFTWARE: Sub HDMI HDMI U1025 MX25L1606EM2I-12G 16M SOFTWARE: DSP ROM U1027 MX25L12835FMI-10G 128M SOFTWARE: GUI ROM HDMI U1041 5M80ZT100C5N TQFP100 SOFTWARE: AUDIO PLD...
Page 61
1.3. File structure on USB Memory Copy the update files to the USB memory with the following structure: USB memory root Model Name Model Area Product ID AVR-X2100WE3 North America (E3) 000100680100 AVR-X2100WE2/E1 Europe (E2) / Asia (E1) 000100680200 AVR-X2100WE1C China (E1C) 000100680500 AVR-X2100WK Japan (JP) 000100680400 AVR-S900WE3 North America (E3) 000100680700 + firmwares...
Page 62
1.5. Start the update. AVR-X2100W ·Hold down buttons "TUNER PRESET CH +" and "STATUS" at the same time and press the power button to turn on the power. AVR-S900W ·Hold down buttons "ZONE2 SOURCE" and "TUNE +" at the same time and press the power button to turn on the power.
Page 63
1.10. About the error code See the table below for error codes and details of faults when the firmware is updated through USB memory. Error Details of Error code Display Coping strategies Code Disconnect and connect the USB Unable to detect USB. C o n n e c t i o n F a i l 0 1 memory.
Page 64
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. BlockErase failed before rewriting If the FL display stops at the Error dis- E r a s e f a i l Main.
Page 65
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. TimeOut in USBCheck. If the FL display stops at the Error dis- C o n n e c t i o n F a i l 3 9 play, press and hold the "Power opera- tion"...
Page 66
Error Details of Error code Display Coping strategies Code This unit automatically retries several Abnormal data in UpdatePacket times. Wait until the FL display stops. received from CX870 (FormatEr- If the FL display stops at the Error dis- U p d a t i n g f a i l ror).
Page 67
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. Mismatched CheckSum in Check- If the FL display stops at the Error dis- U p d a t i n g f a i l Sum comparison after rewriting.
Page 68
1.11. Device display during firmware update Display of target device during firmware update. Target device Display Error code when an error occurs 08 - 0B 10 - 15 Main CPU 20 - 27 M a i n : * * % * * * m i n 36 - 3B 50 - 52 54 - 58 S u b : * * % * * * m i n...
2. Updating by DPMS Download the latest firmware from the internet and update the firmware. 2.1. Network Connection (1) System Requirements • A broadband internet connection • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Settings Internet Computer Modem ComputerLAN port / Ethernet connector...
Page 70
2.3. About the error code See the following table for details on the error code, details of the error code, display and coping strategies when updating the firmware from DPMS. (DPMS:Denon Product Management Server). Error Details of Error code Display...
Page 71
Error Details of Error code Display Coping strategies Code Main CPU failed to receive Turn on the power again. Update will firmware for rewriting sent from U p d a t i n g f a i l start automatically. CX870 (when an error occurred).
Page 72
Error Details of Error code Display Coping strategies Code Check the network connection. Update Connection to DPMS has timed in an environment where there is a C o n n e c t i o n F a i l 3 9 out when rewriting the Main CPU.
Page 73
Error Details of Error code Display Coping strategies Code DSP, PLD etc. failed to receive the Turn on the power again. Update will firmware for rewriting sent from U p d a t i n g f a i l start automatically.
Page 74
Error Details of Error code Display Coping strategies Code Notified that the access to the Check the network connection. Update DPMS is congested line, when in an environment where there is a S e r v e r b u s y A 3 rewriting the CX870 system (Ap- small network load.
Page 75
Device display during firmware update Display of target device during firmware update. Target device Display Error code when an error occurs 08 - 0C 10 - 15 Main M a i n : * * % * * * m i n 22 - 24 36 - 3E 50 - 52...
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DV voltmeter. (2) Place the unit in normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. (3) Settings of This Unit •...
SURROUND MODES AND PARAMETERS Contents Connections Playback Settings Tips Appendix Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. DThis indicates the audio output channels. The output channels depend on the settings of “Speaker Config.” (v p. 183). Channel output Sound mode (v p.
Page 78
Contents Connections Playback Settings Tips Appendix Surround Parameter (v p. 146) Neo: 6 Audyssey (v p. 152) Pro Logicg/gx Music mode only Music Restorer modes only Tone Control Sound mode (v p. 115) (v p. 111) Panorama Dimension Center Center Dynamic MultEQ Dynamic EQ...
Page 79
Contents Connections Playback Settings Tips Appendix Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. 2-channel signal Multi-channel signal Analog /PCM Dolby Digital DTS-HD DTS Express DTS Dolby TrueHD Dolby Digital Plus Dolby Digital EX Dolby Digital Sound mode (v p.
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator on Does the power indicator on the the front panel flash in green front panel flash in red when the or white when the power is power is turned on? turned on?
2. Analog video COMPONENT/HDMI OUT NG Input CVBS Input OMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI TO "3 HDMI/DVI" To A <HDMI PCB> test point HDMI PCB CLAMP1000 7020-07498-020-0S [MP] C2174 N1019 CLAMP1001 R1374 U1050 C1293 R1371...
Page 82
Input CVBS / COMPONENT Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the following points? HDMI PCB Check the connection between Input CVBS:Check B : R2092 the PCBs. Input COPONENT:Check C COMPONENT-Y : R2089 COMPONENT-Cb : R2091 COMPONENT-Cr : R2090...
Page 83
Input CVBS Check the set value of each IC. Are the voltage values as follows? HDMI PCB The HDMI PCB is faulty. N1018 - 3pin : Hi(3.3V) N1018 - 4pin : Hi(3.3V) N1018 - 5pin : Lo(0V) Use the jigs to extend the HDMI PCB.
Page 84
Input COMPONENT Check the set value of each IC. Are the voltage values as follows? The HDMI PCB is faulty. HDMI PCB N1018 - 2pin : Lo(0V) N1018 - 6pin : Hi(3.3V) Use the jigs to extend the HDMI PCB. Is the power supply voltage Check the connection between the being output correctly?
(6) Are the HDMI output settings of the Blu-ray/DVD player correct? and set the HDMI output correctly. (7) If using a DENON Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES if using a Blu-ray/DVD player from another com- pany.
Page 86
•Check the circuits around the IP SCALER (U1026, Is "IP SCALER NG" displayed? HDMI PCB) and DDR2 (U1028/1029). (See page) If there appear to be no problems, U1026 or U1028/1029 is faulty. See "AVR-X2100W-S900_HDMI Rx-Tx Failure Detection Procedure Manual ver_1.00" of SDI.
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO Legacy BLOCK Audio output OK? COAX or OPT Don't care (PCM or DolbyDigital or dts…) CHECK3...
Page 88
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuit- Replace the power transistor. 2SB1560/2SD2390 Is the emitter resistor of the power transistor open? Replace the emitter resistor. 0.47Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 89
4.3. Analog audio No audio output. Is a voltage of ±7V supplied to INPUT Repair the ±7V power supply. PCB CN4006? Is there an audio signal in INPUT Repair the power amplifier. PCB CN401? Connect the connectors correctly. Is electron volume serial data being Is the connector correctly connected sent to INPUT PCB CN4200? with HDMI PCB?
5. Network/Bluetooth/USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn Is the LAN cable correctly inserted? on the power again. Check the connection environment Set the IP address, etc. correctly. If the IP settings are fixed, check that no Are the network settings of this unit correct? other devices have the same IP address and...
Page 91
The circuit between the AC inlet and N1029 Can a voltage (5V) be confirmed between pin 2 and pin 5 of is faulty. Check the SMPS PCB. N1029? Can an output voltage (3.3V) to Is D5V_POWER (U1018 uCOM 85pin) The circuit of D5V_POWER between U1070(DC-DC Conv.) be confirmed? "Hi"...
Page 92
5.2. Cannot connect to the Bluetooth Can a voltage (5V) be confirmed between pin 1 and pin 4 of N1036 on The circuit between the AC inlet and N1036 is faulty. HDMI PCB? Check the SMPS PCB. The circuit between N1036 of the HDMI PCB and Can a voltage (5V) be confirmed pin 10 of CP6001 on Bluetooth CP6001 of the Bluetooth PCB are faulty of wire or PCB?
Page 93
5.3. A connected USB device is not recognized. Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16 and FAT32-formatted mass storage class, MTP- Is the USB device supported by this unit? compatible devices and iPods (with the exception of some models).
6. SMPS DC 5V is not output. Replace the IC4140 (TOP258MG) and Is IC4140 (TOP258MG) damaged? D4142 / D4143 / D4144 / D4145. Are there the damage in D4142 / Has a fuse (F4140) broken? Replace the damaged part(s). D4143 / D4144 / D4145 / IC4140? Are there any short circuits caused by Repair the short circuited area(s) by the the soldering of the PCB?
Page 96
Operation waveform for each part Primary drain After primary side rectification (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) OPTION OPTION OPTION After secondary rectifications OPTION T4140 ● OPTION ● ● ● TR4140 IC4140 OPTION SMPS unit (Unloaded)
Page 103
AVR-S900/X2100W LEVEL DIAGRAM ZONE2 R2A15218FP from F-ch from DA SB-ch SPEAKER + LINE IN + MAIN NET/USB DAC ZONE2 (AVRX2100 ONLY) +30dB SP OUT 0dBFS PCM5100 2.0Vrms MAX SIGNAL LEVEL 2.00Vrms +20dB +20dB 0dBFS +10dB -10dBFS +10dB -20dBFS(DIG.IN) -2.0dB LINE IN 200mV -20dBFS PREOUT...
POWER DIAGRAM AVR_S900 / X2100 / OTHER AVR1 VCC DIAGRAM S1(AMP +B) AC OUTLET S2(+8V,-8V) OTHER AVR1 ONLY MAIN TRANS AC CORD OTHER AVR1 ONLY NET3.3V(CX870/MFI341S2164) NET1.2V(CX870) MAIN PWR ON NET1.8V(CX870:OPEN) NET1.9V(CX870)
AVR-X2100 BT Mother B'D R6009 U6000 R6010 LDO_ON R6011 CLK_32K BT_3.3V IC6000 U6001 CP6001 CP6001 TO N7005 GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL VIDEO SIGNAL COMPONENT(Y) SCHEMATIC DIAGRAMS (4/30) 04-BlueTooth...
CPU LEVEL CHG TO 4B REMOTE3.3V SWM3.3V M3.3V TO 5B DGND OPEN SWM3.3V R1366 DGND 14 13 12 11 10 Q1032 RT1N141C SCPURXD SCPUTXD TO 7B TO 6B GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL VIDEO SIGNAL COMPONENT(Y) SCHEMATIC DIAGRAMS (5/30)
SUB CPU TO A4 TO A9 TO C6 SCPU5V SCPU3.3V DGND SBUBDOWN DSP1CLK DV_POWER2 DSP1MISO DV_POWER1 TO C7 DSP1MOSI CEC_POWER DSP1RST DA_POWER DSP1CS TO D5 DSP1FLAG0 TO D4 ADV7850_INT AVSDA AVSCL R1469 ADV7850_RST TX/RX TO 8F SCPURXD SCPUTXD TO B7 AVSDA AVSCL ADV8003_RST...
TO D6 TO 5D MP OPEN N1034 1.0-16-6PB-2 DSP1CS DSP1MISO DSP1MOSI DSP1CLK DGND DA3.3V MP OPEN R1562 OPEN N1027 1.0-16-10PB-2 DTCK DTDO R1566 OPEN R1567 DTMS TRST DTRST EMU0 DEMU0 R1568 EMU1 DTDI OPTION TABLE MODEL R1576 R1583 AVR-X2100 OPEN AVR-S900 OPEN R1574...
DIR/A.PLD TO F2 TO B1 TO 9E TO C5 TO 1D TO F1 *FILTER COMPONENTS VALUE TYPE TOLERANCE R1907 680 Ω METAL FILM OR CARBON 0 Ω ≤ 5% 0.068UF FILM OR CERAMIC (CH OR C0G) ≤ 5% C2065 0.0047UF C2067 FILM OR CERAMIC (CH OR C0G) ≤...
OPTION D CN4701 OPTION E TO N1014 TO N1015 CP4201 CP4205 TO CP4006 TO CP4007 TO N1013 TO N1016 OPTION A CN4006 CN4703 CP4203 CP4200 1.0-9-4PW AVR_X2100 E3 : 7P OTHER AVR1 : 11P OTHER : OPEN OPTION A OPTION B OPTION L U1047:A C2137...
CVBS INPUT SW NJM2595MTE1 INPUT OTHER OUT PUT AVR_S900/X2100 SW1 SW2 SW4 SW5 AVR1 MUTE MUTE VIN 3 CBL/SAT VIDEO / ZONE2 PART VIN 4 * MODEL / AREA OPTION VIN 2 NOT USED V.AUX MODEL AVR-S900 AVR-X2100 OTHER AVR1 E2/E1/E1C/JP U1B/N1B/K1B AREA...
FRONT_CNT PART CP3401 TO N1033 CP3404 TO N1018 CP3401 CP3404 AVR-S900 X2100 OTHER AVR1 CP5001 CP5004 CP5000 TO CN5004 CP5004 CP5000 TO CN5000 CP5001 TO CN5001 CP5003 CP3403 OPTION B OTHER AVR1 ONLY CN4002 CN4003 CP4605 CN4002 TO CP4002 OPTION B CN4003 TO CP4003 OTHER AVR1 ONLY...
RC-5 PART OTHER AVR1 ONLY JACK5005 CHASSISGND GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL VIDEO SIGNAL COMPONENT(Y) SCHEMATIC DIAGRAMS (23/30) 23-VIDEO_RC5...
TUNER / REG PART TO G3 CP4003 OPTION A CP4003 CP4002 IC4000 TO CN4003 CP4002 TO CN4002 IC4001 AVR_S900/X2100 : 4700UF/25V OPTION D OTHER AVR1 : 6800UF/25V IC4002 IC4003 OPTION C OPTION F CP4006 OPTION B CP4006 TO CN4006 * MODEL / AREA OPTION MODEL AVR-S900 AVR-X2100...
RS232 PART RS_CNT PART (AVR_X2100E3 / OTHER AVR1 ONLY) (AVR_X2100E3 / OTHER AVR1 ONLY) CP4700 TO CN4701 INPUT 1/1 C1 OTHER AVR1 ONLY IC4700 CP4700 JACK4700 AVR_X2100E3 : 7P OTHER AVR1 : 11P CP4703 CP4702 IC4701 JACK4702 OTHER AVR1 ONLY HDAM 1/1 A1 RS232 PART CN4702...
EXPLODED VIEW Please see the last chapter for the part list. J X3 K X3 29 X2 1차 부착 2차 부착 25X2 J X3 TOP COVER [SAME AS AVR13SERIES] A X5 A X2 A X6 21 X5 H X21 AVR-X2100SPE1C 41-1 G x4 I X2...
PACKING VIEW Please see the last chapter for the part list. *MANUAL POLYBAG ASSY* POLYBAG CODE : 6337-04006-201-0S UK plug ZIPPER BAG (A4size) (UK Only) Notes on RADIO ( ALL ) SAFETY INST. ( ALL ) S.S.LIST (JP Only) WARRANTY ( E3 Only ) INSERTION SHEET ( AVR-X2100WE3 Only ) SPK WIRE LABEL ( ALL ) FM ANTENNA ( ALL )
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F56108VNFP (HDMI : U1018) PE0/D8 PC4/A20 PD7/D7 PC5/A21/SCK5/CS5#-D PD6/D6 PC6/A22/RxD5/CS6#-D PD5/D5 PC7/A23/TxD5/CS4#-D/CS7#-D PD4/D4...
Page 147
Pin Name Symbol Pu/Pd STBY STOP Function STBY REMOTE POWER(232C) 232C POWER SUPPLY (REMOTE 3.3V) (X2100W(NA))/ 18 P85 control pin.(ON: H) NC(S900W/ X2100W(EU/CH/AP/ JP)) 19 RES# RESET Reset input (reset: L) 20 XTAL XTAL Oscillator connection 21 VSS 22 EXTAL EXTAL Oscillator connection 23 VCC...
Page 148
Pin Name Symbol Pu/Pd STBY STOP Function STBY 58 P82/TRCLK FL CE VFD control pin 59 VCC +3.3V 60 P81/TRSYNC FL RST VFD control pin ZVOL 61 P80 ZONE VOLUME control pin DATA(X2100W)/ NC(S900W) 62 BCLK/P53(input) ZVOL 63 P52/RD# CLK(X2100W)/ ZONE VOLUME control pin NC(S900W) ZVOL...
Page 149
Pin Name Symbol Pu/Pd STBY STOP Function STBY PA3/A3/PO19/ DAC(ETHER) DAC (ETHER) MUTE control pin (MUTE TIOCC6/TIOCD6/ MUTE ON="L") TCLKF PRE Z2 PA2/A2/PO18/ Z2 PRE OUT MUTE control pin MUTE(X2100W)/ TIOCC6/TCLKE NC(S900W) PA1/A1/PO17/ CLK MUTE A.PLD MUTE control pin (MUTE Active="H") TIOCA6/TIOCB6 PA0/A0/BC0#/PO16/ PRE MUTE...
Page 150
RX210 Group 1. Overview R5F5210ABDFP (HDMI : U1020) RX210 Group PLQP0100KB-A (100-pin LQFP) (Top view) VREFL0 VREFH0 AVCC0 AVSS0 R5F5210ABDFP Terminal Functions Note: • This figure indicates the power supply pins and I/O port pins. For the pin configuration, see the table “List of Pins and Pin Functions (100-Pin LQFP)”.
Page 151
Symbol Pin Name Pu/Pd STBY Function LvCnv STBY 34 P12/SCL/IRQ2 778_1_RST HDMI MN8647781(TX) RESET control pin ※ 35 PH3 HSDA HDMI I2C- MN8647781 3VPu 36 PH2/IRQ1 HSCL HDMI I2C- MN8647781 3VPu 37 PH1/IRQ0 778_1_HINT HDMI MN8647781(TX) HDMI INT input pin 38 PH0 778_2_RST HDMI MN8647781(RX) RESET control pin...
Page 152
Symbol Pin Name Pu/Pd STBY Function LvCnv STBY 85 PD1/IRQ1 DSP1CS DSP control pin (ADSP21487KSWZ-3B) 3VPu 86 PD0/IRQ0 DSP1FLAG0 DSP control pin (ADSP21487KSWZ-3B) 87 P47/AN007 88 P46/AN006 VIN A COMPOSITE VIDEO SELECT IC(NJM2595) 89 P45/AN005 VIN B COMPOSITE VIDEO SELECT IC(NJM2595) 90 P44/AN004 VIN C COMPOSITE VIDEO SELECT IC(NJM2595)
Page 155
DESCRIPTION NAME TOLERANT Reset Input, active low(2) (4) RXIN1 Biphase signal, input 1, built-in coaxial amplifier VDDRX – – Power supply, 3.3 V (typ.), for RXIN0 and RXIN1. RXIN0 Biphase signal, input 0, built-in coaxial amplifier GNDRX Ground, for RXIN Oscillation circuit input for crystal resonator or external XTI clock source input(5) Oscillation circuit output for crystal resonator AGND...
Page 156
ADSP21487KSWZ3B (HDMI : U1024) PIN 1 GND PAD (PIN 177) at BOTTOM TOP VIEW (PINS DOWN) ADSP21487KSWZ3B Terminal Function Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. SDDQM DAI_P10 DPI_P08 FLAG0 SDCKE DPI_P07 FLAG1 DAI_P20...
Page 157
W9864G6JH-6 (HDMI : U1023) W9864G2IH W9864G6JH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 158
W9864G6JH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 159
PCM1690 (HDMI : U1048) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 — —...
Page 160
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 PCM1690 RSV2 — — — Reserved, tied to analog ground AGND2 — — — Analog ground 2 VCC2 — — — Analog power supply 2, +5 V RSV2 —...
Page 161
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100 (HDMI:U1052) PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM Charge pump flying capacitor terminal for negative rail VNEG...
Page 163
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 11-Input selector And Tone control PIN DESCRIPTION R2A15218FP Pin Function PIN No. Function Name 23,21, FROUT,FLOUT, 17,15, COUT,SWOUT, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel 11,9, SROUT, SLOUT, SBROUT,SBLOUT 24,20, FRC,FLC, 18,14, CC,SWC, Connects capacitor for reducing click noise of 12,8, SRC,SLC, L/R/C/SW/SL/SR/SBL/SBR channel volume...
Page 164
I GENERAL DESCRIPTION I PACKAGE OUTLINE The NJM2595 is a 5-input 3-output video switch. Its switches select one from five signals received from VTR,TV,DVD, TV-GAME and others. BD3812F (INPUT:IC5202) The NJM2595 is designed for audio items, such as AV amplifier and others.
Page 167
MAIN MAIN PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 168
MAIN REF No. Part No. Part Name Remarks Q'ty New C4035 X7R)1000PF-K/50V-1608REEL E3/E1C/K D011102777160S C4035 C,CERAMIC CHIP HIK // X7R)0.1UF-K/50V-1608REEL E2/E1 D011104577160S C4038 X7R)1000PF-K/50V-1608REEL E3/E1C/K D011102777160S C4038 C,CERAMIC CHIP HIK // X7R)0.1UF-K/50V-1608REEL E2/E1 D011104577160S C4041 X7R)1000PF-K/50V-1608REEL E3/E1C/K D011102777160S C4041 C,CERAMIC CHIP HIK // X7R)0.1UF-K/50V-1608REEL E2/E1 D011104577160S C4044...
Page 169
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 171
VIDEO VIDEO PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 172
VIDEO REF No. Part No. Part Name Remarks Q'ty New CP3401 C125Z1-11 11P BtoB HEADER(MALE) P=1.25MM L109012511140S CP3404 C125Z1-17 17P BtoB HEADER(MALE) P=1.25MM L109012511740S CP5000 C125Z1-11 11P BtoB HEADER(MALE) P=1.25MM L109012511140S CP5001 C125Z1-13 13P BtoB HEADER(MALE) P=1.25MM L109012511340S CP5003 YMAW025-08R DIP RA L102025080010S CP5004 C125Z1-07 7P BtoB HEADER(MALE) P=1.25MM...
Page 173
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 174
INPUT REF No. Part No. Part Name Remarks Q'ty New C2139,2140 00D2570507976 CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C2141 00D9630333203 100UF-M/16V,5*11-5RE,SHL SY D040101083090S C2142 00D2570507976 CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C2145 00D9630333203 100UF-M/16V,5*11-5RE,SHL SY D040101083090S C2146 00D2570505910 CH)1500PF-J/50V-1608REEL GRM1882C1H152JA01D D010152167165S C2148 00D2570507976 CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C2151 00D2570505910 CH)1500PF-J/50V-1608REEL GRM1882C1H152JA01D...
Page 176
7CH_AMP 7CH_AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 177
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New R467,468 00D9630345903 RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R469 5.6K-J,1/16W-1608REEL C20005626M160S R471 1.2K-J,1/5W-52RE-AX C00001226P520S R473 33K-J,1/5W-52RE-AX C00003336P520S R474,475 00D9630345903 RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R476 2.7K-J,1/5W-52RE-AX C00002726P520S R478 3.3K-J,1W-R.REEL C060033265050S R479 560-J,1/5W-52RE-AX...
Page 178
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New R612 963125012630S 22-J,1W-5REEL C060022065050S R613 150-J,1/5W-52RE-AX C00001516P520S R614,615 1.2K-J,1W-5REEL C060012265050S R616 47-J,1W-R.REEL C060047065060S R617 1.2K-J,1/5W-52RE-AX C00001226P520S R618 100K-J,1/5W-52RE-AX C00001046P520S R620 RSD-R0-1WJ-4.7K P=5MM SMALL R.REEL N113135647230S R623 963252100140D DHPTHF1608 471P 105T SMD PTC THERMISTOR F320471001050S R624 RSD-R0-1WJ-4.7K...
Page 191
CX870_MIDDLE CX870_MIDDLE PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 192
EXPLODE EXPLODE ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 193
EXPLODE REF No. Part No. Part Name Remarks Q'ty New GASKET 4400210609000S SPRING KNOB 372021056600DS 963411103170D BUTTON 5KEY S900 5090215371000S 963411103180D BUTTON 4KEY S900 5090215361000S SPEAKER REAR SHEET 1217212349000S 963419100910S BUSH,WIFI ANT 2410210161000S 963419100920S HOLDER,WIFI ANT 4320211391000S 963419100930S SUPPORTER,WIFI ANT 4070212301000S 41-1 963116100530S...
Page 194
S900 5707000009150S 963549101000D MIC STAND ASSY 4148210170000S ┣ AVRX2100 PAPER WH A3/MIC BASE A 4140210170000S ┣ AVRX2100WBKE3(DENON) PAPER WH A3/MIC BASE B 4140210180000S ┣ AVRX2100WBKE3(DENON) PAPER WH A3/MIC BODY A 4140210190000S ┣ AVRX2100WBKE3(DENON) PAPER WH A3/MIC BODY B 4140210200000S ┣...
Need help?
Do you have a question about the AVR-X2100W and is the answer not in the manual?
Questions and answers