Page 2
Nota Compatibilidad: USB (2.0) de alta velocidad Clases: UMS (clase de almacenamiento masivo USB) Video Sistema de señal: PAL/NTSC Salida de video compuesto: 1 Vpp ~ 75 ohmios Salida de video por componentes: 0,7 Vpp ~ 75 ohmios Salida HDMI: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Audio Salida estéreo analógica...
Safety instruction, Warning & Notes Safety instruction 1. General safety 2.Laser safety Safety regulations require that during a repair: This unit employs a laser. Only qualified service personnel . Connect the unit to the mains via an isolation transformer. may remove the cover, or attempt to service this device .
Page 4
Warning 1.General 2. Laser . All ICs and many other semiconductors are susceptible to . The use of optical instruments with this product, will electrostatic discharges (ESD). Careless handing during increase eye hazard. repair can reduce life drastically. Make sure that, during .
Page 5
- lead free BGA-ICs will be delivered in so-called respected by the workshop during a repair: ‘dry-packaging’ (sealed pack including a silica gel Use only lead-free solder alloy Philips SAC305 with pack) to protect the IC against moisture. After order code 0622 149 00106. If lead-free solder-paste is...
Page 6
QSG for DVP3560K/55: Register your product and get support at DVP3560K www.philips.com/welcome DVD PLAYER DVP3560K HDMI HDMI OUT & AUDIO OUT...
Enciende la unidad o pasa al modo de espera. Unidad principal Abre o cierra la bandeja de discos. c DISC MENU DVD PLAYER DVP3560K Accede o sale del menú del disco. Pasa al modo de disco. Durante la reproducción de una c d ef g...
Mechanical and Dismantling Instructions Dismantling Instruction Detailed information please refer to the model set. The following guidelines show how to dismantle the player. Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1). Figure 1 Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first.
Page 10
Mechanical and Dismantling Instructions Detailed information please refer to the model set. Dismantling Instruction Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3). Note: Make sure to operate gently otherwise the guider would be damaged. Figure 3 Step4: Dismantling Front Panel, disconnect the connectors (XP80 , XP7, XP476), need release 3 snaps of Front Panel &...
Page 11
Mechanical and Dismantling Instructions Dismantling Instruction Detailed information please refer to the model set. Step5: Dismantling Loader, disconnect the 3 connectors (XP2, XP3, XP4) aiming in the below figure, and remove 1 screw that connects the loader and the bottom cabinet. (Figure 5) Figure 5 Step6: Dismantling Main Board, first disconnect the connector (XP1), and then remove 4 screws.
Softeware upgrade and region code change Preparation to upgrade software 1) Power on the set and open the tray, then press "5""5" B. Read out the software versions to confirm upgrading on remote control to check the SW File Name. 2) Start the CD Burning software and create a new CD Power on the set and press "Setup"...
Trouble shooting chart Spindle motor does not move Motor no move Check the FFC connection Correct connection between 24P and the loader. Check the MO_VCC power Check whether “MO_VCC” voltage is normal. supply (+5V) Check whether laser voltage Check/Replace Q5,Q6,Q7,Q8. (1.9V for CD &...
Page 14
Trouble shooting chart The power can not be on or off The power can’t be on or off Check the power supply Repair the power board on the power board is normal. Check if the XS301 on the front board to XP5 on the Check/Correct connection decoder board is in good contact.
Page 15
Trouble shooting chart All output voltages on the power board is 0V or deviated. All output voltages on the power board is 0V or deviated Check whether Replace F1 F1 is blown Replace C1&C2 if D1, D2, D3, D4 are Check whether there is normal.
Page 16
Trouble shooting chart Disc cannot be read . Disc cannot be read. Check the FFC connection Check the loaded circuit between 24P and the loader. 1.Check voltage on pin 15 of U20 varies between 0 and 3.3V: Check whether there is laser 3.3V for CD voltage (1.9V for CD and 2.4V for 0V for DVD...
Page 17
Trouble shooting chart Only DVD disc or only disc except DVD can be played Only DVD disc, or only disc except DVD can be Played. Check Check the loaded circuit connection between 24pin and the loader. Check laser voltage (2.4V) Check the solder status on U20 and output on L10, if pin10 of U20 is peripheral components...
Page 18
Trouble shooting chart No display on LED, and buttons do not work No display on LED, and buttons do not work Check whether there is correct contact between Correct connection XS301 and XP5 Fix power supply board top a Check VCC(+5v) voltage power supply should...
Page 19
Trouble shooting chart Distorted audio and loud noise Distorted audio and loud noise Check the power supply voltages +12V Check Q3 operation amplifying Q3 is normal. Check whether the muting Replace R167 R152 transistor R167 R152 are normal Check whether the muting transistor Q48,Q50, Replace Q48,Q50,...
Page 20
Trouble shooting chart Abnormal color of video picture Abnormal color of video picture Check whether Check Y2, R20,R27,C22 and C23 27MHz output signal Check whether the 3.3V Check other of power supply electric and 1.8V power supply circuit voltages on the decoder board are normal.
Page 21
Trouble shooting chart Remote reception is insensitive or fails. Remote reception is insensitive or fails. Check if the remote Check battery control works properly. Check if the power supply Check R315 C315 voltage to the remote censor is normal Use an oscilloscope to check if there is output waveform from the first pin REM301(PIN1 - RC waveform) IR of the remote censor after pressing...
Page 22
Trouble shooting chart 5-10 No video picture, no sound. No video picture, no sound. Check whether all the voltages Check the loaded circuit from the power board to the CVBS(R21 point) waveform decoder board are normal. Check if the reset circuit consisting ofCE7, D2 is normal (at a low level Change CE7, D2.
Page 27
Power Board Circuit Diagram: * CAUTION : THE PARTS MARKED WITH ARE IMPORTANT PARTS ON THE SAFETY. PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL. F501 F501 TR501 TR501 T2AL/250ac T2AL/250ac NTC 10 NTC 10 P501 P501 D501 D501 D502...
Page 28
TO POWER BOARD Main Board Circuit Diagram: POWER SUPPLY 5pin/2.5mm 5pin/2.5mm MO_VCC +5VD FB AXIAL FB AXIAL DV33 960mA +5VP NC/0 NC/0 +P12V C112 C112 0.1uF 0.1uF SS8550 SS8550 0.1uF 0.1uF DV33 TO FRONT PANEL R113 R113 R120 R120 R115 R115 R118 R118...
Page 35
7-12 7-12 OK Board and USB Board Print-layout (Top and Bottom side):...
Page 36
7-13 7-13 Power Board Print-layout (Bottom side):...
Page 37
7-14 7-14 Main Board Print-layout (Top side):...
Page 38
7-15 7-15 Main Board Print-layout (Bottom side):...
Page 39
Exploded view for DVP3560K/55: It is a general mechanical exploded view for DVP3560K/55, pls refer to the model set for detailed information. ASSY1 includes components:1.3.4.5.21...