Controls; About The Standby Indicator - Kenwood KRF-V5010 Service Manual

QQ
3 7 63 1515 0
For VR-205, VR-255,
KRF-V5010
Speaker indicator
MUTE indicator
1
STANDBY STANDBY
POWER
ON / STANDBY ON / STANDBY
POWER
- ON
PHONES
For U.S.A.
and Canada
TE
L 13942296513
9
1 POWER key
(For U.S.A. and Canada)
Use to turn the power ON/OFF.
STANDBY indicator
1 ON/STANDBY (
(Except for U.S.A. and Canada)
Use to switch the power ON/STANDBY
when the POWER is turned ON.
STANDBY indicator
2 POWER key
(Except for U.S.A. and Canada)
3 DIMMER key
Use to adjust the brightness of the display.
4 P.CALL keys (Except for VR-257)
Use to call up previously registered radio
stations.
5 BAND key
Use to select the broadcast band.
www
6 AUTO key
Use to select the auto tuning mode.
.

About the STANDBY indicator

This unit has a STANDBY indicator. When the STANDBY indicator is lit, the unit consumes a small amount of power to preserve the memory. This is called
STANDBY mode. This mode also lets you turn the power ON using the remote control.
KRF-V5010/V6010/V7010/VR-205/206/207/255/257
Frequency display,
Input display,
Preset channel display,
Surround mode display
SP
SP A B TI.VOL
* **** **
MUTE
RDS EON PTY
TP TA NEWS
Speaker selection indicators
Output channel indicators
2
For VR-257
SAP SIGNAL
AV SURROUND RECEIVER
MAIN
SAP
SPEAKERS
VIDEO 2/
A B BASS BOOST MONITOR
– OFF
0 ! @ #
SPEAKERS MUTE
For VR-205, VR-255 and KRF-V5010
7 MEMORY key
Use to store radio stations in the preset
memory.
8 VOLUME CONTROL knob
9 PHONES jack
) key
Use for headphone listening.
0 SPEAKERS A key
Use to turn speaker system A on and off.
SPEAKERS key
(VR-205, VR-255, KRF-V5010)
Use to turn the speakers on and off.
! SPEAKERS B key
Use to turn speaker system B on and off.
MUTE key
(VR-205, VR-255, KRF-V5010)
Use to temporarily mute the sound.
@ BASS BOOST key
Use to select the maximum adjustment
setting for the low frequency range.
x ao
y
i
8

CONTROLS

AUTO SOUND indicator
(VR-257)
Band indicators
FM
* ;
AM
MHz
kHz
Display
For VR-257, please refer to
separate booklet for SAP function.
3 4 5 6
DIMMER P.CALL P.CALL BAND AUTO
MULTI CONTROL
SOURCE
DIRECT LISTEN MODE SOUND SETUP
Q Q
3 6 7 1 3
$ % ^ & *
u163
.
2 9 9 4 2 8
PRO LOGIC
indicator
S.DIRECT indicator
AUTO indicator
AUTO SOUND AUTO
MEMO. indicator
PRO LOGIC
S.DIRECT MEMO.
ST. indicator
3 STEREO
MONITOR ST.
DOWNMIX DSP TUNED
TUNED indicator
MONITOR indicator
DSP indicator
3 STEREO indicator
STEREO indicator
7 8
VOLUME CONTROL
MEMORY
INPUT SELECTOR
DOWN
1 5 0 5 8 2 9 9 4
(
# VIDEO 2/MONITOR key
$ SOURCE DIRECT key
% LISTEN MODE key
Use to select the listening mode.
^ SOUND key
Use to adjust the sound quality and ambi-
ence effects.
& SETUP key
Use to select the surround sound settings.
* MULTI CONTROL knob
Used to make a variety of settings.
( INPUT SELECTOR knob
Use to select the input sources.
m
co
9 9
UP
2 8 9 9
3