Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Durapac PAT-1114
Summary of Contents for Durapac PAT-1114
-
Page 1: Instruction Manual
Instruction Manual Air Torque Wrench Power Unit Model – PAT-1114 Maximum Operating Pressure – 700 bar ABSOLUTE EQUIPMENT PTY LTD – 2/186 Granite Street, GEEBUNG QLD 4034 – Australia sales@absoluteequipment.com.au – Phone: +61 7 3865 4006 – Fax: +61 7 3102 6288... -
Page 2: Product Information
The user must ultimately make the decision regarding suitability of the product for any given task and assume the responsibility of safety for all in the work area. Contact a Durapac representative if you are unsure of your power unit’s suitability for a particular application. - Page 3 Hydraulic equipment must only be serviced by a qualified hydraulic technician. For repair service, contact the Durapac authorised service centre in your area. To protect your warranty, use only high quality hydraulic oil CAUTION: ...
-
Page 4: Installation
Do NOT subject the power unit and its components to shock loads Use only Durapac approved accessories and components Ensure that the chosen application is stable to work on and around Do NOT connect to an application which can return more oil to the reservoir than the power unit reservoir can hold ... -
Page 5: Operation
4.1 Familiarise yourself with the specifications and illustrations in this owner’s manual. Know your power unit, its limitations and how it operates before attempting to use. Refer to the specification chart below or if in doubt, contact a Durapac representative. Flow (Lpm) - Page 6 Durapac Air Torque Wrench Power Units have been specifically designed to integrate seamlessly with Durapac TW and LPC-Series Torque Wrenches. There is a 2-way, 4 position air control valve on the pump. Port A is a high pressure port - it delivers the oil at a high pressure.
-
Page 7: Maintenance
Damage to hydraulic hoses may not be detected during visual inspections. For this reason, Durapac recommends that hydraulic hoses be replaced on a regular basis Ensure that the air source of the pump is shut off before beginning any maintenance or repairs Dirt, sand, etc. -
Page 8: Bleeding Air From The System
Wipe clean thoroughly and store in a clean, dry environment. Avoid temperature extremes. 6.4.3 For transportation or long storage, replace the air vent plug with shipping plug. 6.4.4 Shield pump with a protective cover. PAT-1114 Power Units - V1.1 www.durapac.com Page 8 of 15... -
Page 9: Troubleshooting
Refer to 6.1 – Adding Hydraulic Fluid Oil too cold Control the temperature to at least -10°C Dirt in pump or filter is Replace filter and clean tank clogged PAT-1114 Power Units - V1.1 www.durapac.com Page 9 of 15... -
Page 10: Parts Breakdowns And Lists
Air motor 11 Regulating valve Oil/water seperator 12 Oil gauge Air input valve 13 Oil drain plug Radiator 14 Screw Air valve 15 Metal plate Pressure gauge 16 Oil filling port PAT-1114 Power Units - V1.1 www.durapac.com Page 10 of 15... -
Page 11: Power Unit
Oil return pipe 10 Male elbow Petrol pipe 11 Nylon tube (500mm long) Oil return pipe 12 Air supply bracket Cooling pipe 13 Female bulkhead fitting Oil/water separator 14 Reservoir gasket PAT-1114 Power Units - V1.1 www.durapac.com Page 11 of 15... - Page 12 19 Low Pressure Piston 20 High Pressure Piston 2 21 High Pressure Piston 2 22 Pin 23 Bearing end plate 24 Elastic washer 25 Screw 26 Connector 27 Screw 28 Filter PAT-1114 Power Units - V1.1 www.durapac.com Page 12 of 15...
-
Page 13: Valve System
7.2 Pressure meter joint 13 Sealing ring 3.8 O-ring 7.3 O-ring 14 Elastic washer Check valve assy Regulating valve assy 15 Washer 4.1 Check valve body 8.1 Valve body 16 Screw 4.2 Ring PAT-1114 Power Units - V1.1 www.durapac.com Page 13 of 15... -
Page 14: Remote Control
Remote case ZAW1578 1 Air valve ZAW1579 1 Button ZAW1580 1 Circlip ZAW1581 1 Complete Assembly ZAW1577 1 Serial, model and part numbers need to be quoted when ordering parts. PAT-1114 Power Units - V1.1 www.durapac.com Page 14 of 15... -
Page 15: Hydraulic Schematic
Instruction Manual 9.0 Hydraulic Schematic PAT-1114 Power Units - V1.1 www.durapac.com Page 15 of 15...
Need help?
Do you have a question about the PAT-1114 and is the answer not in the manual?
Questions and answers