Lincoln 1999 Town Car Owner's Manual
  1. Manuals
  2. Brands
  3. Lincoln Manuals
  4. Automobile
  5. 1999 Town Car
  6. Owner's manual

Lincoln 1999 Town Car Owner's Manual

Ford motor company 1999 lincoln town car owner's guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Before driving
Starting and driving
Starting
Servicing
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright
1998 Ford Motor Company
Contents
2
3
21
80
105
109
123
141
181
187
199
200
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1999 Town Car and is the answer not in the manual?

Questions and answers

Related Manuals for Lincoln 1999 Town Car

Summary of Contents for Lincoln 1999 Town Car

  • Page 1 Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.

  • Page 2: Introduction

    Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.

  • Page 3: Instrumentation

    Instrumentation...
  • Page 4 Instrumentation Panel dimmer switch (pg. 21) Headlamp control (pg. 21) PANEL Turn signal and wiper/washer control (pg. 55) Instrument cluster (pg. 6) CHECK TRAC km/h SERVICE ENGINE SOON MIST RESUME SET ACCEL COAST Speed control Climate controls (pg. 55) Driver side air bag (pg.
  • Page 5 Electronic sound system (pg. 28) BASS TREB FADE TAPE SEEK TUNE SCAN AUTO SIDE 1 2 COMP SHUFF SELECT RESET FRONT REAR AUTO Climate control systems (pg. 22) Instrumentation Clock* (pg. 52) Passenger side air bag Traction control switch* (pg. 111) (pg.

  • Page 6: Warning Lights And Chimes

    Instrumentation WARNING LIGHTS AND CHIMES TRUNK AJAR DOOR AJAR CIRCLE TRAC OFF AIR SUSPENSION SLOWLY O/D OFF TRAC ACTIVE SPEED CONTROL COMPASS SERVICE ENGINE SOON Service engine soon Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II).
  • Page 7 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap.
  • Page 8 Instrumentation Brake system warning Momentarily illuminates when the ignition is turned to the ON BRAKE position, the engine is off and the parking brake is engaged. If the brake warning lamp does not illuminate at this time, seek service immediately. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately.
  • Page 9 Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service. Engine oil pressure Momentarily illuminates when the ignition is turned to the ON position and the engine is off.

  • Page 10: Air Suspension

    Instrumentation Trunk ajar If the trunk is not completely closed, this light comes on when you turn the ignition to ON. With the ignition ON, this light will flash five times and sound a tone for one second, then remain on. Door ajar Illuminates when one of the doors is not completely shut and the ignition...

  • Page 11: Speed Control

    O/D off Illuminates when the transmission control switch (TCS) has been pushed. When the light is on, the transmission does not shift into overdrive. If the light does not come on when the TCS is depressed or if the light flashes when you are driving, have your vehicle serviced.

  • Page 12: Headlamps On Warning Chime

    Instrumentation Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter.
  • Page 13 Odometer Registers the total kilometers (miles) of the vehicle. Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
  • Page 14 Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
  • Page 15 see how many kilometers/miles you can drive before running out of fuel. see how many liters/gallons of fuel remain in the fuel tank. monitor the average fuel economy. monitor the instantaneous fuel economy. monitor the average speed. check the distance traveled during a trip on either Trip A or Trip B. You can select different features for the message center to display by using the message center controls located in the center of the instrument panel.
  • Page 16 Instrumentation Compass display (if equipped) The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions.
  • Page 17 Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. 2.
  • Page 18 Instrumentation Checking your highway fuel economy using the electronic message center display The following procedure will allow you to accurately monitor your actual highway fuel economy. Since this procedure requires the vehicle speed control system to be set to highway speeds, it must be run only on suitable roadways where long distance speed control can be safely maintained.
  • Page 19 DIST TO EMPTY (DTE) This function estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few kilometers (miles).
  • Page 20 Instrumentation When this function is displayed, FUEL ECON AVG press the RESET control to change FUEL REMAIN the message center display from DIST TO EMPTY metric to English units or from AVG SPEED English to metric units. TRIP A B...

  • Page 21: Controls And Features

    PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. Push up to brighten. Push down to dim. AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
  • Page 22 Controls and features the headlamp system is not turned on by another feature such as using the headlamp control or Autolamp. The Daytime Running Light (DRL) system will automatically illuminate the tail lamps and parking lamps at dusk (when the headlamp control is in the OFF position).
  • Page 23 Turning the EATC on Press AUTO, any of the override controls or the fan speed control. The EATC will only operate when the ignition is in the ON position. Turning the EATC off Press OFF. The Outside Temperature (EXT) function will continue to operate until the ignition is turned off.
  • Page 24 Controls and features Temperature selection The display window indicates the ˚ selected temperature, function (AUTO or one of the override controls) and manual control of fan AUTO speed ( ) if automatic fan speed is not desired. To control the temperature, select any temperature between 18°C FRONT (65°F) and 29°C (85°F) by pressing...
  • Page 25 Controls and features Fan speed ( When AUTO is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, press the fan control to cancel automatic fan speed operation or use the steering AUTO wheel fan speed control.
  • Page 26 Controls and features MAX A/C-Uses recirculated air to cool the vehicle. The temperature display will remain unchanged and air will be cooled based on the selected temperature. To exit, press AUTO or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster.
  • Page 27 Displaying outside temperature Press EXT to display the outside air temperature. It will be displayed until EXT is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
  • Page 28 Controls and features If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle.
  • Page 29 Controls and features Volume/power control Press the control to turn the audio VOL - PUSH ON system on or off. Turn the control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
  • Page 30 Controls and features Tune adjust The tune control works in radio mode. Tune adjust in radio mode Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
  • Page 31 Controls and features Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
  • Page 32 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Tape select To enter tape mode while in radio mode, press the TAPE AMS control.
  • Page 33 selection). The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape. In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least 4 seconds duration between programs. Rewind The rewind control works in tape mode.
  • Page 34 Controls and features The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode. To set the hour, press and hold the CLK control and press: to decrease hours and to increase hours.
  • Page 35 The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.), the media information will again display for ten seconds before reverting back to the clock.
  • Page 36 Controls and features Alpine Audio System with Premium AM/FM Stereo Cassette (CD Changer Compatible) PUSH ON TAPE MUTE Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
  • Page 37 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
  • Page 38 Controls and features to increase volume compensation to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
  • Page 39 Tune adjust for CD changer Press to select the previous disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs.
  • Page 40 Controls and features Scan function The scan function works in radio, tape or CD mode (if equipped). SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
  • Page 41 Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2.
  • Page 42 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
  • Page 43 In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in tape and CD modes (if equipped). In the tape mode, tape direction will automatically reverse when the end of the tape is reached.
  • Page 44 Controls and features Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. The effect of the feature varies with the music content. Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the...
  • Page 45 Use the SEL control to select ON or OFF. With the feature on, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data). Program type Press the RDS control until the FIND program type is displayed.
  • Page 46 Controls and features Use the SEL control to select TYPE, NAME or NONE. RDS clock feature Refer to Setting the clock for information. Phone mode This feature allows you to control the factory-installed cellular phone (if equipped) through the radio controls.
  • Page 47 JAZZ CLUB—jazz club with clearly reflected sounds. HALL—rectangular concert hall capacity of about 2 000 CHURCH—church with a high vault. STADIUM—outdoor stadium with a capacity of about 30 000. NEWS—“voice-only” type of sound with a limited audio band. Press the DSP control until one of the following appears: ALL SEATS DRIVER SEAT...
  • Page 48 Controls and features CD changer (if equipped) The CD changer is located in one of the following locations: in the trunk in the center console under the driver’s seat 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine.
  • Page 49 Controls and features If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder.
  • Page 50 Controls and features The CD magazine may be inserted or ejected with the radio power off. ONLY use the magazine supplied with the CD changer, other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty.
  • Page 51 Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care Use only cassettes that are 90 minutes long or less. Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold.
  • Page 52 Controls and features Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.
  • Page 53 Press the left control to decrease the time displayed. AUXILIARY POWER POINT The auxiliary power point is located under the instrument panel. This outlet should be used in place of the cigarette lighter for optional electrical accessories. POSITIONS OF THE IGNITION 1.
  • Page 54 Controls and features KEY SYSTEM The vehicle is equipped with a master key and valet key lock system. The master key will actuate doors, trunk, glove box, ignition and remote trunk release. The valet key (marked “valet”) will actuate doors and ignition only.
  • Page 55 WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
  • Page 56 Controls and features Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off Press OFF or Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased.
  • Page 57 Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To set a higher set speed Press and hold SET/SET ACC/ SET ACCEL. Release the control when the desired vehicle speed is reached or Press and release SET/SET ACC/ SET ACCEL.
  • Page 58 Controls and features To disengage speed control Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
  • Page 59 STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Radio control features Press BAND/MODE to select AM, FM1, FM2, TAPE or CD (if equipped). In Radio mode: Press MEM/NEXT to select a preset station from memory.
  • Page 60 Controls and features Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of the gearshift lever. The Transmission Control Indicator Light (TCIL) will illuminate on the instrument cluster. The transmission will operate in gears one through three. To return to normal overdrive mode, press the Transmission Control Switch again.
  • Page 61 Controls and features Programming 1. Prepare for programming the HomeLink Universal Transceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLink Universal Transceiver surface (located on your visor) while keeping the red light in...
  • Page 62 Controls and features To program your hand-held transmitters: continue to hold the button on the HomeLink Universal Transceiver. press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. Operating the HomeLink Universal Transceiver Once programmed, the HomeLink Universal Transceiver can be used in...
  • Page 63 Controls and features 3. Press and release the programmed HomeLink button. Press and release the HomeLink button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door.
  • Page 64 Controls and features MOON ROOF (IF EQUIPPED) To open the moon roof: Press and release the control. For one-touch operation, press and release the rear portion of the control; this will fully open the moon roof. To stop one-touch operation at the desired position, press and release the forward portion of the control.
  • Page 65 Controls and features Do not block the sensor on the backside of the mirror since this may impair proper mirror performance. Press the control to turn the mirror on or off. The mirror will automatically return to the normal state whenever the COMP MIRROR vehicle is placed in R (Reverse)
  • Page 66 Controls and features Fuel filler door override release If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk to open the fuel filler door. POWER WINDOWS Express down To make the driver window open WINDOW LOCK fully without holding the window control, press the driver window...
  • Page 67 Accessory delay (if equipped) With accessory delay, the window switches, radio, and moonroof may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened. POWER DOOR LOCKS Press control to unlock or lock all doors.
  • Page 68 Controls and features Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
  • Page 69 To program position one, move the driver seat to the desired position using the seat controls. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1. To program position two, repeat the previous procedure using control 2. A position can only be set or recalled when the transmission gearshift is in Park or Neutral.
  • Page 70 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. The horn will chirp and the parklamps/taillamps will flash to confirm that the control was...
  • Page 71 Controls and features Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view.
  • Page 72 Controls and features nearby radio towers structures around the vehicle other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART.
  • Page 73 The system automatically turns off after 25 seconds or when the ignition is turned to the START or ACC position. The inside lights will not turn off if: they have been turned on with the dimmer control or any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed.
  • Page 74 Controls and features Memory seat/mirrors feature (if equipped) The remote keyless entry system can also control the memory seats/mirrors feature. With this feature, the first two programmed transmitters will recall a different memory position. Press the control once to unlock the driver’s door and move the memory features to the corresponding memory position, just as if you had...
  • Page 75 KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, you can: lock or unlock the vehicle doors without using the key. Your vehicle has a factory-set 5–digit code that operates the keyless entry system. You can also program your own 5–digit personal entry code.
  • Page 76 Controls and features You can program up to three personal codes to unlock your vehicle. These codes do not replace the permanent code that the dealership gave you. Erasing personal code To erase all of the personal entry codes programmed to a vehicle: 1.
  • Page 77 Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. To lock the doors: 1. Press 7/8 and 9/0 at the same time. SECURILOCK PASSIVE ANTI-THEFT SYSTEM Your vehicle is equipped with a coded-key anti-theft system. Only the correct key will be able to start your vehicle.
  • Page 78 Controls and features Spare SecuriLock keys can be purchased from your dealership and programmed to your SecuriLock Programming spare SecuriLock If one or both of your SecuriLock to ensure the lost or stolen key will not operate your vehicle, bring your vehicle and all available SecuriLock reinitialization.
  • Page 79 Controls and features Procedure to program spare SecuriLock keys to your vehicle New SecuriLock keys must have the correct mechanical key cut for your vehicle. Conventional (non-SecuriLock ) keys cannot be programmed to your vehicle. You will need to have two previously programmed SecuriLock keys and the new unprogrammed SecuriLock key readily accessible for timely...

  • Page 80: Seating And Safety Restraints

    Seating and safety restraints SEATING Head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
  • Page 81 Seating and safety restraints Press the control to recline the seatback forward or backward. Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down.
  • Page 82 Seating and safety restraints Adjusting the power seats – seat mounted controls Never adjust the driver’s seat or seatback when the vehicle is moving. The power seat controls are located on the side of the driver’s seat. Press to raise or lower the seat, or to move the seat forward or backward.
  • Page 83 Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness. Using the manual recline function (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
  • Page 84 Seating and safety restraints Memory seats (if equipped) This system allows automatic positioning of the driver seat and outside rearview mirrors to two programmable positions. The memory seat control is located on the driver door. To program position one, move the driver seat to the desired position using the seat controls.
  • Page 85 All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
  • Page 86 Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free...
  • Page 87 How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
  • Page 88 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height control down.
  • Page 89 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
  • Page 90 Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
  • Page 91 AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) CHECK TRAC km/h SERVICE ENGINE SOON PANEL MIST Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
  • Page 92 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
  • Page 93 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the...
  • Page 94 Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
  • Page 95 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
  • Page 96 Seating and safety restraints How does the side air bag system work? The side air bag system consists of the following: An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.
  • Page 97 Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual.
  • Page 98 Seating and safety restraints Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
  • Page 99 If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.
  • Page 100 Seating and safety restraints When installing a child safety seat: Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. Use the correct safety belt buckle for that seating position. Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
  • Page 101 Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back.
  • Page 102 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
  • Page 103 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
  • Page 104 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit.

  • Page 105: Starting

    PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 106 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. Turn the key to 4 (ON) without turning the key to 5 (START). TRUNK AJAR DOOR AJAR CIRCLE...
  • Page 107 Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the light ( illuminate. STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
  • Page 108 Starting To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately.

  • Page 109: Driving

    Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 110 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
  • Page 111 The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle.
  • Page 112 Driving your vehicle. It is especially useful on slippery and/or hilly road surfaces. The system operates by detecting and controlling wheel spin. The system borrows many of the electronic and mechanical elements already present in the anti-lock braking system (ABS). Wheel-speed sensors allow excess rear wheel spin to be detected by the Traction Control portion of the ABS computer.
  • Page 113 STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.

  • Page 114: Transmission Operation

    Driving The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not operate. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
  • Page 115 Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle.
  • Page 116 Driving R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll.
  • Page 117 towing a trailer up or down steep hills additional engine braking is desired. If towing a trailer, refer to Driving while you tow in the Trailer Towing chapter. To return to Overdrive mode, press the transmission control switch. The O/D OFF indicator light will no longer be illuminated. Each time the vehicle is started, the transmission will automatically return to normal Overdrive mode.
  • Page 118 Driving VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: Base Curb Weight : Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. Payload : Combined maximum allowable weight of cargo, passengers and optional equipment.
  • Page 119 Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations.
  • Page 120 Driving Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle.
  • Page 121 Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer. Speed control may shut off if you are towing on long, steep grades. When towing a trailer: Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling.
  • Page 122 Driving Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper. Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability, emissions, reliability and causing internal transmission damage. Replace the rear axle lubricant anytime the axle has been submerged in water.

  • Page 123: Roadside Emergencies

    HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on top of the steering column. Depress hazard lights control to activate all hazard flashers simultaneously.
  • Page 124 Roadside emergencies Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button.
  • Page 125 Standard fuse amperage rating and color Fuse Mini Rating Fuses Grey Violet Pink 7.5A Brown Blue Yellow Natural Green — — — — — Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal.
  • Page 126 Roadside emergencies The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 7.5A 7.5A Lighting Control Module (LCM), Left-Hand Low Beam Headlamp EATC Blower Motor Lighting Control Module (LCM), Right-Hand Low Beam Headlamp Instrument Cluster Lighting Control Module (LCM), Park/Tail Lamps EATC, Heated Seats Lighting Control Module (LCM), Day/Night...
  • Page 127 Fuse/Relay Fuse Amp Location Rating 7.5A 7.5A 7.5A Roadside emergencies Description Electronic Crash Sensor (Airbag) Instrument Cluster, Anti-Theft, Ignition Switch, Ignition Coils Anti-Lock Brake Module, Traction Control Switch Transmission Control Switch, Lighting Control Module (LCM) Multi-Function Switch, Turn Signals Wiper Control Module (WCM), Windshield Wiper Motor Digital Transmission Range (DTR) Sensor, Back-Up Lamps, EC Mirrors...
  • Page 128 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 7.5A 7.5A Relay 1 — Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
  • Page 129 The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 50A** 40A** 50A** 30A** 40A** 30A** 50A** 30A** 50A** 40A** 40A** Roadside emergencies DIODE Ignition Switch Ignition Switch Cooling Fan-High Speed PCM Power Relay I/P Fuse Panel, Fuses 10, 19, 21, 23, 25, 27 Starting System I/P Fuse Panel, Fuses 1, 3, 5, 7, 9, 31 Driver Power Seat, I/P Fuse Panel, Fuse 30...
  • Page 130 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 30A** 15A* 20A* — 30A* 10A* 15A* 30A* 15A* 15A* — — 20A* 30A** 30A CB — Relay 1 — Relay 2 — Relay 3 — Relay 4 — Relay 5 — * Mini Fuses ** Maxi Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.
  • Page 131 Temporary spare tire information Your vehicle may have a temporary or full-size spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only. Replace this tire with a full-size tire as soon as possible.
  • Page 132 Roadside emergencies 3. Remove the spare tire, jack and lug wrench. 4. Remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle. Insert and twist the handle, then pry against the wheel.
  • Page 133 6. Locate the jack notch next to the door closest to the tire you are changing, then place the jack on the frame rail directly behind the notch. Turn the jack handle clockwise until the wheel is completely off the ground.
  • Page 134 (not the dealer) to get a replacement key. If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
  • Page 135 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
  • Page 136 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
  • Page 137 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
  • Page 138 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
  • Page 139 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
  • Page 140 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.

  • Page 141: Maintenance And Care

    SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
  • Page 142 Maintenance and care Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on 1.
  • Page 143 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Engine oil filler cap 4. Air filter assembly 5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8.
  • Page 144 Maintenance and care ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
  • Page 145 If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
  • Page 146 Maintenance and care Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide.
  • Page 147 If you use DOT 5 or any other brake fluid that is not DOT 3 or DOT 4, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry, this may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever...
  • Page 148 Maintenance and care Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid.
  • Page 149 The use of an improper coolant may void the warranty of your vehicle’s engine cooling system. Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine...
  • Page 150 Maintenance and care What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
  • Page 151 When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1.
  • Page 152 Maintenance and care 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines.
  • Page 153 Maintenance and care 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature (H) or ambient temperature (C). Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F).
  • Page 154 Maintenance and care Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and/or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter.
  • Page 155 If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.
  • Page 156 Maintenance and care 4. The relearning process will automatically complete as you drive the vehicle. The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
  • Page 157 Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the...
  • Page 158 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
  • Page 159 SERVICING YOUR TIRES Checking the tire pressure Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
  • Page 160 Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
  • Page 161 wheels (of the same size and specifications) be used as chains may chip aluminum wheels. Follow these guidelines when using snow tires and chains: Use only SAE Class S chains. Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines.
  • Page 162 Maintenance and care Observe the following guidelines when handling automotive fuel: Extinguish all smoking materials and any open flames before fueling your vehicle. Always turn off the vehicle before fueling. Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
  • Page 163 Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops.
  • Page 164 Maintenance and care Vehicles certified to meet California emission standards (indicated on the underhood Vehicle Emissions Control Information label) are designed to operate on California cleaner-burning, low-sulfur gasolines. If you have a California-certified vehicle and California cleaner-burning gasoline is not available when you refuel, your engine should perform adequately.
  • Page 165 if “Regular” unleaded gasoline is recommended because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel.
  • Page 166 Maintenance and care taking fuel economy measurements during the first 1 600 km (1 000 miles) of driving (engine break-in period). You will get a more accurate measurement after 3 000 km–5 000 km (2 000 miles-3 000 miles). Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities chart in this “Owner Guide.”...
  • Page 167 Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy.
  • Page 168 Maintenance and care Maintenance Keep tires properly inflated and use only recommended size. Operating a vehicle with the wheels out of alignment will reduce fuel economy. Use recommended engine oil. Refer to Lubricant Specifications. Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide.
  • Page 169 EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: Use only unleaded fuel.
  • Page 170 Maintenance and care engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your “Warranty Guide” for complete emission warranty information. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system.
  • Page 171 Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach.
  • Page 172 Maintenance and care 4. Remove headlamp by taking the retainer pins out. Pull headlamp forward to access bulb connector. 5. Release clip and disconnect the electrical connector from the bulb. 6. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base.
  • Page 173 Maintenance and care 4. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. 5. Carefully insert the headlamp assembly into the vehicle making sure the retainer pins are inserted into the proper holes and into the guides.
  • Page 174 Maintenance and care Replacing tail lamp/backup bulbs For bulb replacement, see a dealer or qualified technician. Replacing license plate lamp bulbs For bulb replacement, see a dealer or qualified technician. Replacing the interior bulbs Check the operation of the following interior bulbs frequently: interior overhead lamp map lamp Using the right bulbs...
  • Page 175 Maintenance and care A bubble (vertical indicator) that is not centered between the two red lines does not necessarily indicate out-of-aim headlamps. If your vehicle is not positioned on a level surface, the slope will be included in the vertical indication. Therefore, vertical and horizontal headlamp adjustment should be performed only when the beam direction appears to be incorrect.
  • Page 176 Maintenance and care Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, remove protective cover, then locate the bubble level and the vertical adjustment screw. The adjustment screw is located on the outboard side of the headlamp.
  • Page 177 Maintenance and care During winter months, it is especially important to wash the vehicle on a regular basis. Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle. Remove any exterior accessories, such as antennas, before entering a car wash.
  • Page 178 Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage.
  • Page 179 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades and windshield If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent.
  • Page 180 Maintenance and care Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary.

  • Page 181: Capacities And Specifications

    MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery (standard) Battery (optional) Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Engine oil (includes filter change) Brake fluid Power steering fluid Motorcraft MERCON Transmission fluid...
  • Page 182 Capacities and specifications Rear axles are considered lubricated for life when the vehicle is used for normal service. See your Scheduled Maintenance Guide for Severe Duty requirements. Traction-Lok axles use 2.2–2.4L (4.75–5.0 pints) of rear axle lubricant. Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok rear axle.
  • Page 183 Item Ford part name Hinges, Multi-Purpose latches, Grease striker plates, fuel filler door hinge and seat tracks Lock Penetrating and cylinders Lock Lubricant Power Motorcraft steering fluid MERCON ATF Automatic Motorcraft transmission MERCON V ATF (4R70W) Rear axle Motorcraft SAE lubricant 80W90 Premium Rear Axle Lubricant...
  • Page 184 Capacities and specifications ENGINE DATA Engine Cubic inches Horsepower-single exhaust Horsepower-single exhaust Horsepower-dual exhaust Horsepower-dual exhaust Torque-single exhaust Torque-single exhaust Torque-dual exhaust Torque-dual exhaust Required fuel Firing order Spark plug gap Ignition system Compression ratio Vehicles sold in California, New York, Massachusetts and Connecticut only.
  • Page 185 Capacities and specifications...

  • Page 186: Certification Label

    Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.

  • Page 187: Customer Assistance

    In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, it’s found in the Roadside Assistance book in the glove compartment.
  • Page 188 You may purchase Ford ESP from any participating Ford or Lincoln-Mercury or Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage.
  • Page 189 Customer assistance Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs.
  • Page 190 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford, Mercury and Lincoln cars and Ford or Mercury light trucks which are within the terms of any applicable written new vehicle...
  • Page 191 Ford or Lincoln/Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln-Mercury dealership management, recognized for their business leadership qualities. What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form.
  • Page 192 Customer assistance Your dealership and a Ford Motor Company representative are asked to submit statements at this time. To properly review your case, the Board needs the following information: legible copies of all documents and maintenance or repair orders relevant to the case the year, make, model, and Vehicle Identification Number (VIN) listed on your vehicle ownership license the date of repair(s) and mileage at the time of occurrence(s)
  • Page 193 Customer assistance After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
  • Page 194 Customer assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3...
  • Page 195 * May be sold with the Motorcraft name A wide selection of accessories is available through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
  • Page 196 Customer assistance Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running boards...
  • Page 197 Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates...
  • Page 198 Customer assistance theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician. Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use or are not properly installed.

  • Page 199: Reporting Safety Defects

    Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.

  • Page 200: Index

    Index Accessory delay ...67 Air bag supplemental restraint system ...91,95 and child safety seats ...92 description ...91,95 disposal ...98 driver air bag ...93,96 indicator light ...7,94,97 operation ...93,96 passenger air bag ...93,96 Air cleaner filter ...181 Air conditioning ...22 automatic temperature control system ...22 Air suspension ...113 air leveling disabled warning,...
  • Page 201 Coolant ...147,149 checking and adding ...148 refill capacities ...149,181 specifications ...182,184 Customer Assistance ...187 Ford accessories for your vehicle ...194 Ford Extended Service Plan ...188 Getting assistance outside the U.S. and Canada ...193 Getting roadside assistance ...187 Getting the service you need ...189 Ordering additional owner’s literature ...198...
  • Page 202 Index GAWR (Gross Axle Weight Rating) ...118 definition ...118 driving with a heavy load ...118 location ...118 GVWR (Gross Vehicle Weight Rating) ...118 calculating ...118 definition ...118 driving with a heavy load ...118 location ...118 Hazard flashers ...123 Head restraints ...80 Headlamps ...21 aiming ...174,175,176 autolamp system ...21...
  • Page 203 Mirrors automatic dimming rearview mirror ...64 cleaning ...180 heated ...68 programmable memory ...74 side view mirrors (power) ...67 Moon roof ...64 Motorcraft parts ...165,181 Octane rating ...164 Odometer ...13 Overdrive ...59 Panic alarm feature, remote entry system ...71 Parking brake ...110 Parts (see Motorcraft parts) ...181 Power distribution box (see Fuses) ...128...
  • Page 204 Index Transmission ...114 fluid, checking and adding (automatic) ...152 fluid, refill capacities ...181 lubricant specifications ...184 Trunk remote release ...65,71 Turn signal ...8,54 Vehicle dimensions ...184 Vehicle Identification Number (VIN) ...186 Vehicle loading ...118 Ventilating your vehicle ...108 Warning chimes ...12 Warning lights (see Lights) ...6 Washer fluid ...147 Water, Driving through ...122...

  • Page 208: Filling Station Information

    Filling station information Required fuel Fuel tank capacity Engine oil capacity (includes filter change) Tire pressure and size Hood release Coolant capacity Power steering fluid capacity Transmission fluid capacity Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color).

This manual is also suitable for:

Town car 1999

Table of Contents

Save PDF