Troubleshooting - Panasonic KX-TGE260 Operating Instructions Manual
Hide thumbs
Also See for KX-TGE260:
- Quick manual (11 pages) ,
- Operating instructions manual (96 pages) ,
- Quick manual (10 pages)
Table of Contents
Advertisement
Useful Information
Display message
Requires
subscription
to Caller ID.
Use
rechargeable
battery.
Troubleshooting
If you still have difficulties after following the instructions in this section, disconnect the base unit's
AC adaptor, then reconnect the base unit's AC adaptor. Remove the batteries from the handset,
and then insert the batteries into the handset again.
General use
Problem
The handset does not turn on
even after installing charged
batteries.
The unit does not work.
I cannot pair a cellular phone to
the base unit.
68
Cause/solution
R You must subscribe to a Caller ID service. Once you
R A wrong type of battery such as Alkaline or
Cause/solution
R Place the handset on the base unit or charger to turn on
the handset.
R Make sure the batteries are installed correctly (page 11).
R Fully charge the batteries (page 12).
R Check the connections (page 11).
R Unplug the base unit's AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset has not been registered to the base unit.
Register the handset (page 48).
R Depending on the compatibility of the cellular phone, you
may not be able to pair it to the base unit. Confirm that
your cellular phone supports the hands-free profile (HFP)
specification.
R Confirm that the Bluetooth feature of your cellular phone
is turned on. You may need to turn this feature on
depending on your cellular phone.
R The Bluetooth technology on your cellular phone may not
be functioning normally. Turn off and on your cellular
phone.
R If your cellular phone is already connected to another
Bluetooth device such as a Bluetooth headset, turn it off
or disconnect it from your cellular phone.
R Some cellular phones may require you to enter the
Bluetooth PIN to pairing. Confirm that you entered the
correct PIN.
For assistance, please visit http://www.panasonic.com/help
receive caller information after subscribing to a Caller
ID service, this message will not be displayed.
Manganese was inserted. Use only the rechargeable
Ni-MH batteries noted on page 4, 8.
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the KX-TGE260 and is the answer not in the manual?
Questions and answers
I have the model KX-TGE260. I have been using the remote access feature with my cell phone, but lately the code I send does not get the unit to respond. I checked the code and it hasn't changed. It's like the base station doesn't hear the tone numbers. Did something get turned off or is the unit toast?
The Panasonic KX-TGE260 base station may not respond to remote access codes sent from a cell phone due to the following reasons:
1. The remote access code is not set. Set the code remotely (refer to page 60).
2. The wrong remote access code is being entered. Check the current code setting (refer to page 60).
3. The answering system is turned off. Turn it on (refer to page 61).
4. Remote access is not possible when calling from a cellular phone paired to the base unit.
This answer is automatically generated
Base no power show up on the handset. I have tried unplugging the base to reset it, but that didn't work. I try to register the phone and fhe word registering comes. Then it goes back to the message base no power and the word charging underneath that message, but it never charges.
If the Panasonic KX-TGE260 handset displays "Base no power" and does not charge, follow these steps:
1. Move the handset closer to the base unit and try again.
2. Unplug the base unit’s AC adaptor, then reconnect it to reset the unit.
3. Check if the handset’s registration has been canceled. If so, re-register the handset (refer to page 48 of the manual).
4. If the message appears during a power failure, place a handset on the base unit to supply power to it.
These steps should help restore functionality.
This answer is automatically generated