1. Manuals
  2. Brands
  3. Meraki Manuals
  4. Wireless Access Point
  5. MR62
  6. Hardware installation manual

Meraki MR62 Hardware Installation Manual

802.11n access point
Hide thumbs Also See for MR62:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Setup Manual
Meraki MR 62/66
Hardware Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MR62 and is the answer not in the manual?

Questions and answers

Related Manuals for Meraki MR62

Summary of Contents for Meraki MR62

  • Page 1 Meraki MR 62/66 Hardware Installation Guide...
  • Page 2 Meraki, Meraki MR62, MR66, and Meraki Cloud Controller are trademarks of Meraki, Inc. Other brand and product names are registered trademarks or trademarks of their respective holders. Warranty Meraki, Inc. provides a one year warranty on this product. Warranty details may be found at www.meraki.com/support.

  • Page 3: Table Of Contents

    4.2.3 Mount the MR66 4.2.3.1 Attach Antennas 4.2.3.2 Aim Antennas 4.2.3.3 Powering the MR66 with Meraki 802.3af Power over Ethernet Injector 4.2.3.4 Powering the MR66 with an 802.3af Power over Ethernet Switch 4.2.3.5 Attach Power over Ethernet to the MR66 4.2.3.6 Attach Grounding Strap...

  • Page 4: Scope Of Document And Related Publications

    Scope of Document and Related Publications The MR62/66 Hardware Installation Guide describes the installation procedure for the MR62 and MR66 access points. Note: All instructions in this hardware installation guide reference the MR66 but apply equally to the MR62, except where noted.

  • Page 5: Mr66 Overview

    The Meraki MR66 is an enterprise-class, 802.11n access point designed for rugged environments. When connected to the Meraki Cloud Controller, the MR66 enables the creation of high-speed and reliable net works that cover large outdoor and industrial areas quickly, easily, and cost-effectively.

  • Page 6: Understanding The Mr66

    2.2 Understanding the MR66 Your Meraki MR66 has the following features: Accessory antenna attachment holes Mount attachment LED indicators posts (4x) Grounding post 5 GHz Mount 5 GHz Factory reset button Vent Vent The vent allows pressure and humidity equalization between the interior and the enviroment. This prevents internal condensation and maintains a water proof seal.
  • Page 7 Your MR66 mount plate has the following features: Mounting holes (4x) Mount plate attachment slots (4x) Vertical orientation mounting strap slots (2x) Horizontal orientation mounting strap slots (2x) Mount plate attachment screw Release tab Mount plate ground attachment...

  • Page 8: Antennas And Ports

    2.3 Antennas and Ports The Meraki MR66 has two 802.11n radios (the MR62 has one radio). Each radio has two external antenna connectors; both connectors for a particular radio should be attached to the same type of antenna. The 5 GHz radio is used for mesh or client communication.

  • Page 9: Power Source Options

    Error state. May indicate bad gateway or other routing fault The MR66 may be operated in “Run Dark” mode for additional security and to reduce the visibility of the access point. In this mode, the LEDs will not be illuminated. This mode may be enabled through Meraki Dashboard.

  • Page 10: Pre-Install Preparation

    2. Find the network to which you plan to add your nodes or create a new network. 3. Add your nodes to your network. You will need your Meraki order number (found on your invoice if you ordered directly from Meraki) or the serial number of each node, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit.

  • Page 11: Assigning Ip Addresses To Mr66S

    AP) or over a wired connection. If using a wired connection, connect the client machine to the MR66 either through a PoE switch or a Meraki PoE Injector. If using a PoE switch, plug an Ethernet cable into the MR66’s Ethernet jack, and the other end into a PoE switch.

  • Page 12: Collect Tools

    Network cables with RJ45 connectors long enough for your particular mounting location 802.3af PoE power source (either PoE switch or Meraki 802.3af PoE Injector) Connection to the internet (if you are setting up your MR66 as a gateway to the internet) Appropriately sized metal straps (if mounting to a pole larger than 3.9”...

  • Page 13: Installation Instructions

    2. Power over Ethernet supports a maximum cable length of 300 ft (100 m). 3. If being used in a mesh deployment, the MR66 should have line of sight to at least two other Meraki devices. For more detailed instructions regarding access point location selection, reference the Meraki Network Design Guide (meraki.com/support/#documentation).

  • Page 14: Attach The Mount Plate

    4.2.1 Remove the Mount Plate from the Access Point Before installing the mount plate, you must remove it from the back of the access point. 1. Unscrew the mount plate attachment screw. 2. Lift the mount plate release tab upwards. 3.

  • Page 15: Wall Or Solid Ceiling Mount Using Mount Plate

    4.2.2 Attach the Mount Plate The MR66 mount plate can be used to install your access point in a wide range of scenarios. 4.2.2.1 Wall or Solid Ceiling Mount Using Mount Plate Using included wall anchors and screws, attach the mount plate to your mounting wall or ceiling. It is recommended that the MR66 be mounted to a wall or solid ceiling using the mount plate for physical security reasons.

  • Page 16: Mount The Mr66

    4.2.3 Mount the MR66 Insert the posts on the back of the access point into the attachment slots on the mount plate.

  • Page 17: Attach Antennas

    4.2.3.1 Attach Antennas Remove protective plastic covers from all four N-type RF connectors. Attach appropriate antennas (and protective boots if included). 4.2.3.2 Aim Antennas If you are using directional antennas, aim them appropriately to ensure optimal performance for your specific network topography. Omnidirectional antennas perform best in a mesh network when oriented vertically.

  • Page 18: Powering The Mr66 With Meraki 802.3Af Power Over Ethernet Injector

    4.2.3.3 Powering the MR66 with the Meraki 802.3af Power over Ethernet Injector (sold separately) 1. Plug the power cord into the PoE Injector and the other end into wall power. 2. Plug an Ethernet cable that is connected to an active Ethernet connection into the “IN“ port on the injector.

  • Page 19: Attach Power Over Ethernet To The Mr66

    4.2.3.5 Attach Power over Ethernet to the MR66 1. Remove the dust cover from the Ethernet port of the MR66. Unscrew it with a coin or flathead screwdriver. 2. Route the Ethernet cable from the PoE Injector “OUT” port to the MR66. 3.

  • Page 20: Attach Grounding Strap

    4. Plug the Ethernet cable into the Ethernet port of the Meraki MR66. a. Connect the cable to the Ethernet port on the MR66. b. Screw the gland body into the threaded hole of the port. Use an adjustable wrench to make sure the gland body is fully seated in the hole.

  • Page 21: Verify Device Functionality And Test Network Coverage

    Ethernet LED will not be illuminated and the number of green Signal Strength LEDs will show the signal strength to the nearest Meraki device. See section 2.6 for further details about information conveyed by the LEDs. Note: Your MR66 must have an active route to the Internet to check and upgrade its firmware.

  • Page 22: Regulatory Information

    Regulatory Information for MR62 U.S. Regulatory Wireless Notice Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 23 Canadian Regulatory Wireless Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
  • Page 26 Regulatory Information for MR66 U.S. Regulatory Wireless Notice Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 27 The device may not be used in the 5 GHz spectrum unless the 5.725 - 5.875 GHz has been disabled. This can be done through the Meraki Dashboard.
  • Page 30 Copyright © 2011 Meraki, Inc. All rights reserved. Trademarks Meraki® is a registered trademark of Meraki, Inc.
  • Page 31 660 Alabama St. San Francisco, California 94110 Phone: +1 415 632 5800 Fax: +1 415 632 5890...
  • Page 32 © Meraki, Inc. 2011 280-09100-A...

This manual is also suitable for:

Mr66

Table of Contents